How to refill a Brother toner cartridge. How to refill laser cartridges? Working with a printer with a toner cap

Remove the cover. Add toner. Close the lid. Insert back into the device. I must say that refueling the laser is not difficult at all. If you adhere to certain rules and the words "screwdriver" and "pliers" do not lose consciousness. Because it is these tools that are needed in order to self-refill a laser printer cartridge.

Laser printers are filled with a special powder called toner.

Toners are different for all printers. The manufacturer on the toner bottles usually indicates a list of models for which this or that powder is intended.

Toner is chemically very hazardous and should be used with care.

It is important to know if there is a special chip on the cartridge that blocks the operation of the device after the consumable is used up. If so, it's best to take it to a gas station.

Security measures

All components of toner for printing devices are highly toxic. To avoid poisoning, you should wear rubber gloves, a dressing gown or other clothing that you do not mind before refueling the laser printer cartridge.

Replace toner in a well-ventilated area. Since fine particles of toner dust can even pass through a special gas mask. You can arm yourself with a respirator or gauze bandage. But they are unlikely to help, even if the gas mask allows dust particles to pass through.

The table on which the refueling of the laser printer cartridge will be carried out should be covered with a newspaper or something similar.

What the cartridges are made of

There are two types of laser cartridges. Some have a special hole for filling powder into the hopper, others do not. You will have to tinker with such a model in order to get to the toner compartment.

The print device cartridge has two parts. The first is the dye hopper. The second is a container for collecting garbage and powder residues.

Replacing the toner in the cartridge is carried out in two stages: first, cleaning the waste container, then refilling.

How to clean a laser printer cartridge

Now you need to disassemble and clean out the dirt from the garbage container. To do this, use a screwdriver to unscrew the screws that fix the side plugs of the case. Then carefully take out the light-sensitive drum. It is important not to take it with your fingers on the main surface, but try to hold it on the sides or by the gear, otherwise the drum will deteriorate and will be unusable for later use. After the photo is taken out of the case, it is advisable to put it away from the main workspace, covering it with a newspaper or a sheet of paper so that light and dust do not get in.

Then you need to remove the charging roller (rubberized part), which is located under the photosensitive drum. At the same time, remember that all parts must be taken by the side parts. Damage to the surface of these parts will result in poor print quality.

Now we unscrew the cleaning blade called the squeegee. And carefully, so that the remnants of powder and debris do not scatter on the sides, turn over and shake out the container. We thoroughly clean all the parts from paint residues and put them back together. In filling workshops, a special vacuum cleaner is used, with the help of which the entire body of the printing device is cleaned.

Refueling the printer

The toner hopper is located in the second half of the printing unit. Most often, the access to the filling hole is located on the side under the plastic cap. But there are cartridges, the design of which does not provide holes for filling paint. In this case, you have to completely unscrew the cartridge and pour the toner into the slot through which it enters the magnetic roller. Sometimes a hole is made in the hopper, and in this way the cartridges are refilled. Avoiding complete disassembly and cleaning of the entire cartridge.

Having opened the plug of the magnetic hopper, they take the toner purchased in advance from the office equipment store, and with the help of a funnel or A4 sheet rolled into it, pour the powder into the hopper. Do not fill the hopper completely, this may jam the cartridge. It is necessary that one and a half to two centimeters remain to the edge. Then we close the lid, collect both parts and insert the filled cartridge into the device.

Nuances that you need to pay attention to when refilling toners yourself.

It often happens that laser printer cartridges are equipped with a print counter chip. To refuel them, you should contact a specialist to reset the data in the memory of the chip or to replace it. Even if you manage to do all the dirty work at home, the printer will simply refuse to work, because "according to his calculations, the resource has already been used up."

An important question - "How many times can you refill the cartridge?" It all depends on the cartridge itself. On average, this number ranges from 5 to 15 times. Moreover, during every 3–6 refueling, it is necessary to carry out a restoration. This is a procedure for replacing consumables that need to be replaced as they wear out.

In general, refueling is not such a difficult task. But it is worth taking on this business only when there is confidence that everything will work out. Otherwise, you will have to buy a new cartridge, and its cost is often comparable to the cost of the device itself. And all the expected savings from "self-service" will come to naught. If you still have questions about how to refill a laser cartridge, we recommend that you familiarize yourself with the refueling instructions for your particular model. To do this, go to the section.

Instructions
refilling cartridges Brother LC-980, LC-1100

for Brother MFP: DCP-145C, 163C, 165C, 167C, 185C, 383C, 385C, 387C, 585CW

DCP-6690CW MFC-250C, 290C, 297C, 490CW, 790CW, 990CW,

MFC-5490CN, 5890CN, 6490CW

Attention!!! Avoid prolonged printer downtime with empty cartridges! Doing so can dry out ink residues in the print head and block the nozzles. In this case, the printer will not print until you clean the print head!

Use only the correct ink to refill cartridges.

1.Prepare the necessary tools and materials for refueling: ink, small screwdriver, syringe without a needle with a capacity of 10 ml, napkins, rubber gloves.
2.To refill the cartridge, you will need to remove the cap. To do this, use the tip of a screwdriver to pry off the cover from both sides (photo 1).

3. Remove the cover by moving it parallel to the body (photo 2).

Attention! At the same time, 2 metal springs are released and fall out. Don't lose them, they will come in handy when assembling the cartridge.

4. Set the cover and springs aside (photo 3).

5. Put on rubber gloves. Draw ink of the required type and color into the syringe, remove the needle.
6. Press your left index finger on the air vent valve pin when refilling the cartridge.
7. Insert the tip of the ink syringe into the outlet of the cartridge and slowly inject ink while holding down the air valve pin (photo 4).
8. Refill ink until a drop of ink exits through the vent valve.
9.Squeeze the valve (remove your finger) and pull the syringe out of the outlet.
10.To assemble the cartridge, install the springs on the special pins inside the cover (photo 5). Holding the spring cap vertically, slide the rest of the ink tank onto it, making sure that the springs snap into place (Photo 6).

11. Connect both parts of the cartridge until you hear a click. Check the correct fit of the cover on the body: press the cover - it should spring. If the cover does not spring, then it is installed incorrectly - remove it as described above and reinstall it.
12. Install the cartridge in the printer and perform the initial check cycle according to the printer's service manual.
Note: The cartridge has an ink level float sensor, so the printer must detect that the cartridge is full.

Brother printers are renowned all over the world, and those who choose to buy a printer from this brand have made a wise decision in favor of the best value for money. After using Brother office equipment, after a while, it becomes necessary to refill with toner. This procedure can be done with your own hands. For those who decided to find out how Brother TN-1075 self-refilling cartridge, this article will help.

Attention! Do not risk the operation of printing devices, refill the cartridge TN-1075 for printers HL 1110/1112/1210/1212 DCP 1510/1512/1610/1612/1615/1616 MFC 1810/1815/1910/1911/1912/1915/1916 total

This printer is quite easy to maintain, but to start the procedure for replacing the cartridge, you need to follow the detailed instructions, which will be described in detail below. If you are not confident in your own abilities, then the best solution would be to take the consumable to a refueling workshop and deprive yourself of responsibility for costly repair of components or the printing device itself. Let's consider a specific example in which refilling the Brother TN cartridge-1075 .

To start performing the steps step by step, you should prepare the workplace and the necessary tool in advance. We will need:

• compatible toner analog;
• cotton lint-free fabric;
• conductive lubricant;
• vacuum cleaner;
• screwdriwer set.

Step by step instructions for refilling the Brother TN-1075 toner cartridge

We will pre-prepare the workplace, we will follow the points and perform the actions.

Item # 1: unscrew the two screws from the end panel of the cartridge, then pry on the latch and remove it.

Item number 2: remove the magnetic shaft sleeve, and then pull out the gears.

Item number 3: take a flat screwdriver and pry on the magnetic shaft fixing washer. We remove it and put it aside. Next, we pry on two latches that are attached to the base of the gear. The end panel of the part can now be removed.

Panel 4: turn the cartridge over to the other side and unscrew the screw that fixes the side panel next to the filling hole. Using a flat screwdriver, carefully detach the bushings of the magnetizing shaft and remove the socket with gentle movements.

Item number 5: in the same way, we unlock the fasteners of the end panel of the cartridge, after which we remove it, freeing the axis of the magnetization shaft, and proceed to the next paragraph of our instruction. We take out the shaft, after which we proceed to cleaning it with a dry, lint-free cloth.

Item number 6: unscrew the two screws of the metering blade, which is also attached to the body with glued foam rubber. After removing the blade, you need to clean the hopper from the remaining ink. This can be done using a vacuum cleaner.

Item number 7: The blade should be cleaned with gentle movements using a dry cloth and isopropyl alcohol. Let's start cleaning the magnetization shaft with a dry cloth (wipe the contacts and its sleeve with alcohol).

Item number 8: if you have retained the printer's warranty, fill the camera with the required amount of toner. This can be done in the open hole of the magnetizing shaft. If the warranty period has expired, then we assemble the body of the consumable in the reverse order and fall asleep toner for Brother cartridges into a special hole on the bunker itself.

Item number 9: put the metering blade in place and secure it with screws on both sides. Now you can install the magnetic shaft and treat its contacts and feed roller with a special conductive grease.

Item number 10: we mount the shaft sleeves, fixing them with screws on the side where the filling hole is, after which we fix the magnetic shaft with a washer.

Item No. 11: install the gears in the sequence shown in the picture. If you are refilling the starter cartridge, you need to check the new reset box and side panel, because the old cover does not fit due to the lack of a slot for this box. If in your case there is no checkbox, you should reset the counter manually, for this see point 13 of this manual.

Item number 12: install the last gear, then close it with the end panel and fasten it with two screws.

Item No. 13: the consumable is ready for testing. If you have not replaced the flag and cartridge cover, we recommend that you perform the manual reset of the toner counter. After that, let's start testing and turn on the printer. We remove the sheets of paper from the feed tray and stick our hand through it. Click on the sensor lever, it is on the left.

Item number 14: hold the sensor, then close the top cover of the printer and wait for the motor to rotate. We release the sensor and after 1-2 seconds we clamp it until the motor stops completely. When the green LED is on, it means the reset was successful. If it is lit red - the procedure is repeated.

If refilling the Brother TN-1075 cartridge seemed too difficult for you, you should contact Miraxprint specialists for help, who will replace the toner in 10-20 minutes, while taking full responsibility for the operation of the office equipment.

Refilling a cartridge for a brother printer is not as easy as it seems at first glance. We suggest that you familiarize yourself with the stages of refueling and its features.

In addition to the high quality of printing, users appreciated Brother cartridges for the fact that they are not chip-based, and this greatly facilitates the process of refilling them. Instead, a refilled cartridge sensor is used, which is located on the side of its cap. Therefore, after the device is refueled, it is necessary to return the sensor flag to its previous position. But for the refueling itself, you need to open the compartment where the toner is located and shake out the rest of the material.

To safely refill your brother cartridge, you need to:

1. Remove tape on the toner box cover, then open the cover itself using a flat-blade screwdriver.
2. To shake out the remains of the old toner, you must use a special vacuum cleaner or a plastic bag. This manipulation must be done with extreme caution.
3. After that you need remove the magnetic roller holder, for which the screws are unscrewed.
4. Then with the same flat screwdriver carefully locks are removed.
5. Now you need remove the magnetic shaft.
6. And again you need eliminate toner residues vacuum cleaner from the shaft and blade.
7. After that the shaft is installed in place, the locks are put on, then the levers are installed, for which the screws are screwed back.
8. Now into the storage bin new toner is filled... After completing this procedure, you must close the cover and turn the shaft slightly so that the filled toner is evenly distributed over it.

From now on, the cartridge is tucked... But if a starting device was used before, then a pendulum must also be installed. To do this, you need to remove the starting tooth from the cover, after which, with a drill, very carefully and with slow rotation, make a hole in which the pendulum will be mounted. It is important that the lower gear is level, otherwise the page counter will not work correctly. Then a pendulum is attached under the spring and small slots are made in the cover of the device with a clerical knife. The cover can now be placed back onto the cartridge to ensure the correct tooth alignment. From this moment on, the starter cartridge becomes not only filled, but also full.

It is also worth noting that Brother cartridges the quality of the printing performed does not differ from the models of such manufacturers as HP or Samsung, but the absence of chipping significantly reduces the initial cost of document prints. Remember that the cartridge must be installed in the printer when the printer is powered on.

We have described the entire refilling algorithm for the brother tn 1075 cartridge and other models, but it is worth remembering that only professionals can do this job efficiently without damaging the cartridge and its components. By ordering services for refilling Brother cartridges from us, you save nerves, time and money spent on repairing your favorite printer!

Brother Toner Cartridge TN-2080 refills like most Brother Toner Cartridges
The appearance of the cartridge assembled with a drum unit.

The capacity of the TN-2080 cartridge is small. Holds about 60 grams of toner
Thus, the Brother TN-2080 can print from 500 to 700 pages - this is the volume of his refueling.

To refill this cartridge, you need to unscrew the three side cover screws and remove the cover.
The starter cartridge (the one that comes with the printer) will not have a large gear for zeroing the counter. In the photo, it has a newer look than the others, because was installed later and did not have time to "grow old"
Detaching the plastic holder
To remove it, pry it open with a flat screwdriver.
Then you need to pry with a screwdriver, as shown in the photo below, the magnetic roller holder.

The magnetic roller can now be removed
Unscrew the two screws to remove the dosing ruler.
We clean the toner cartridge from the remains of old toner and dust. Wipe the dosing ruler and magnetic roller with acetone and a cloth.
Fill the cartridge with new toner through the bore of the magnetic roller. And then the cartridge can be reassembled in reverse order.