entranceHow to fold your headphones to tangle. Headphones get confused? Simple and effective solution
Instructions
There are special storage containers. Everything is provided for your convenience: you carefully wind the headphone wires on a special base, and they no longer have any possibility of tangling. Also handbags (cases) for storing headphones, sometimes they come with. But even in them, the wires often manage to get tangled. You can choose a container or cover convenient for you in any hardware store, contacting a sales consultant for help.
You can fold them neatly by wrapping them around the player. At first glance, this method may seem complicated, but in reality it is not. Take the wire 5-10 centimeters before the plug and fold a regular medium-sized loop out of it, press it against the player. Keeping the shape of the loop, wrap the headphones tightly around the player.
Stack the speakers together. From those going, make a small loop, stepping back from the speakers 5-7 cm. Put the small loop into the big one - the one you created at the beginning, press the small loop with your finger to the player. In this case, pull on - will be tightly wound on. To "" this design, you just need to pull the speakers.
If you store the headphones separately from the player, fold them as follows: spread the fingers of your left hand (if you are right-handed, and on your right hand if you are left-handed) and carefully wrap the headphones around your palm, leaving the end of the wire 10-15 centimeters. Remove the headphones from your hand, and with the remaining end of the wire, start wrapping the resulting “ring” of the headphones. You will get two symmetrical eyelets. When the wire is almost empty, thread the plug through one of the loops. Pull it to one side (towards the loop through which it is threaded) and the speakers to the other. The headphones are folded comfortably.
Sources:
- how to make headphones wirelessly
All mp3 player users have to deal with the problem of tangled headphones. Even if the process of unraveling them is not too long, it annoys many. Therefore, it is worth learning how to wind up the headphones so that you can use them immediately, without unnecessary body movements.
Instructions
It is necessary to rewind correctly, first of all, in order to increase their service life. Headphone breakage is primarily due to cable breaks inside the rubber winding. This is that they do not have external manifestations of breakage, but the sound will not be all the same, or it will be, but only in one of the earbuds. Currently, the most expensive headphone models have additional fabric wrapping over the inner rubber. This reduces the voltage of the wire.
Lately, many headphones began to have a built-in reeling system, which is similar to the one used in fishing spinning rods when reeling in the fishing line. Produce such headphones the first were Koss and Gembird. If in the hands of the usual headphones-, then it's worth about how to quickly rewind headphones.
It is necessary to take headphones- inserts in the hand so that the mini-jack (the connector that is inserted into the player) lies in the palm of your hand. Now you need to start wrapping around the palm, namely around four fingers, starting with the index and ending with the little finger.
As soon as only half the length of the wire remains free, you need to remove the already wound loops from the fingers and rewind them around the remaining length of the wire.
At the end of this procedure, a pair of earbuds is inserted into either of the loops. Now to unwind headphones, you just need to remove the earbuds from the loop.
This method is far from the only one. If you have a player at hand, you can remove the mini-jack from it, and then wrap the wire around the player and put it in a bag or table, depending on the situation.
For any headphones, moisture is also the worst enemy. Under no circumstances should the headphones be used in rain or snow. It is known from the school physics course that the colder, the smaller the distance between the molecules of matter. Frost increases the internal tension on the wire, which significantly shortens the life of the audio headset.
Tip 3: How to fold portable headphones so they don't get tangled
There is no dispute about tastes - a golden rule that applies in many areas of life. In order not to argue about music and not to impose listening to your favorite songs on people around you, you should use individual headphones.
Instructions
The modern music and technology industry offers a wide variety of gadgets for listening to music - from bulky professional equipment to amateur small mp3s. For a mobile and busy person, portable players are great, accompanied by small headphones that, when rolled up, easily fit into a pocket.
Headphones "droplets" and "", for all their ease of use, have perhaps the only significant drawback: sometimes their wires get tangled so much that a lot of time and effort is spent on straightening. The best way to keep the headphone wires straight and intact is with a small purse. Choose an accessory slightly larger than your player.
A zip-fastened case works well. Now, before you put the player in your bag, wrap the headphone wires around it and place the device in the case. A comfortable, sturdy bag will not only prevent the earbuds from getting tangled, but will also protect the gadget from possible damage.
You can quickly and neatly roll up the headphones without the help of additional items. Take both "droplets" in your left hand perpendicular to the palm so that the wires are directed upward (in the direction of the extended thumb). Use four fingers to grip the headphones into a fist. With your right hand, moving clockwise, wrap the wires around your palm. Make the loops tight and hold them with your fingers so that the new layers of wire overlap, but not. Gently attach the resulting "ring" to the player and put it in a small pocket - if it is not too loose, the headphones will not get tangled.
The next method is suitable for long-term and neat storage of headphones without a player. Extend the index finger and little finger of your right hand, while clamping the middle and ring fingers near the palm. Disconnect the headphones from the player and hang them on your index finger so that the "droplets" hang down to the outside of your palm. Run the wires by the little finger to the side of the nail, make a "ring" around the finger and lift the wires up to the index finger.
Wrap the wires in and around it in the same way, then "go down" down. Twist the wires around your fingers in a figure-eight pattern, moving from your index finger to your little finger. Support the wires with your thumb to prevent them from sliding or getting tangled. Wrap the free end of the wire around the thinnest part of the figure eight - the one that remains between the fingers. Remove the headphones from your fingers, thread the wire through one of the rings of the figure eight - this will fix the composition.
note
Follow your personal hygiene and regularly clean your headphones with antibacterial wipes, because germs can get into your ear with the dirty surface of the gadget.
Your headphones are tucked away in the bag in the most neat way possible, they still end up tangled anyway. In order not to waste time untangling the wires, you need to learn how to fold them correctly.
Try simply winding the headphone wires around the player. So that they do not slide off it, do not get tangled even more, they must be properly fixed. Stack the headphone speakers together. From the wires that come from them, roll up a small loop. Take the end from the plug and make the loop larger. Slip the first eyelet into the second. Pull the plug while pressing the small loop against the player. Your headphones will be firmly attached to the player. To disassemble the structure, just pull on the speakers.
You can store the neatly folded headphones separately from your player or phone. To do this, wrap the wires around your palm. The ring of them will then need to be removed, so do not wrap tightly. Leave the wire from the plug free. Carefully remove your winding from the palm of your hand with your free hand. With the left end, begin to pull the resulting ring, holding it between your thumb and forefinger. You should have two symmetrical stitches. Insert the plug into the middle of the wires wrapped around the ring and pull it to the side. In this case, the speakers must be well pinched with your fingers. When folded in this way, the wires will no longer get tangled.
Try another method. Fold the middle and ring fingers of either hand towards the base of the palm. Press down on the speakers with these fingers. Wind the wires from the earbuds around your index and pinky fingers in a figure-eight shape, leaving a small end extending from the plug. Let go of the speakers, which until now have been trapped between two fingers and the palm of your hand. Wrap the end of the wire from the speakers, and at the same time the middle of the figure eight with a wire starting from the plug. Slide the plug into this middle and pull it out to the side. That's it, your headphones are stowed securely.
If all manipulations are difficult for you, buy a special container for portable headphones. Everything is foreseen in it. You just have to wind the wires from the headphones on a special base and carefully put the container in the bag. You can also use soft headphone cases. They can be leather or sewn from dense fabric. Choose the option convenient for you in the audio equipment store. Contact the consultant of this store for help if you are at a loss with a choice.
Related Videos
Tangled headphone wires are a perennial problem for most people who use them. Hurriedly tossing your headphones into your bag or backpack, the rest of the way home, you untangle the wires like a garland. We will tell you about a couple of tricks that will help you avoid this.
Important: to avoid mechanical damage, do not pull the headphone cable too tight.
Roll the wire into a figure eight
1. Fold your hand as if you were throwing a "goat" at a rock concert.
2. Press down on the headphones with your thumb.
3. Wrap the wire around your little finger on the outside of your hand, then around your index finger on the inside.
4. Roll the headphones in this way, leaving a small piece of wire.
5. Tie the coiled headphones in the middle with it.
6. Plug the plug into the loop formed from below.
7. Pull on opposite ends of the earbuds to unwind them.
Wrap the wire around your fingers
The method is not so elegant, but simpler and faster. It was shared by Dieter Bohn of The Verge. Wrap the headphones around three fingers, then tie the rest of the wire in the middle and remove the plug into the loop. In this way, you can wind up not only headphones, but also other cables.
Do you know other convenient ways? Share them in the comments.
There is no modern person in the world who would never take a kitten ball out of his pocket or bag instead of headphones. This Gordian knot is the cause of hundreds of domestic troubles and work procrastination. This knot is a real headache that everyone dreams of getting rid of.
Do you think this is a trivial task? No matter how it is! According to legend, a hero who can untangle this knot will become the ruler of all Asia! But I want to cut it. And here we come to the rescue with a selection of 7 ways to securely and neatly fold the headphones.
1. Special devices
Let's start with the obvious and simple, that is, unworthy of the Russian Kulibins' method - special fasteners for wired earbuds. They can be made in various forms, but the main thing here is the content, that is, in fact, the fasteners. Typically, these devices have a coil and clip for the edge of the headphones.
2. Player or phone
This option is especially useful for athletes who have not yet acquired a Velcro-fastener for a phone on the shoulder or waist. You just need to put the headphones to the back wall, then wind the headphones on the player or phone from which you are listening to music and thread the plug through the loop.
3. Office paper clip-binder
A paper clip is a truly versatile item that can serve as a stand for a smartphone, keyboard, or even beer bottles in the refrigerator. And with a paper clip, you can securely fix the headphones. To do this, you need to insert the headphones into the clip, wind the wire and thread the remaining edge through the rings. An important note: the design is extremely reliable, but not suitable for carrying in a pocket.
4. "Goat"
The goat method dates back to ancient rites of ancient metalworkers who helped keep headphones intact in any pocket. The method has come down to our times in its original form. The method is extremely simple and does not require any foreign objects, but it does take practice. The headphones themselves should be pressed with the ring and middle fingers to the palm of your hand, spread your index finger and little finger and wind the wire from the headphones with a figure eight around them. The remaining end should be threaded through the resulting loop.
5. Boy scout method
We found this method in a note by Medusa, and the original belongs to the editorial staff of The Verve. Take the long end, fold three fingers, wrap the wire around them. When about 25 cm remains, make a loop and fold the rest of the wire in the opposite direction. Finally, thread the droplets themselves through the hole where the fingers were - and voila! It takes 10 seconds to fold the headphones and only two to unravel them. In general, watch and learn!
6. Wine stopper
Finally, we offer the most original way for aesthetes. To prevent the headphones from getting tangled in your pocket, we suggest wrapping them around a wine cork! Firstly, it is budgetary - if you are not an ardent collector-connoisseur, you will most likely throw out the cork from an empty wine bottle. Secondly, it is practical - the cork has no sharp corners and will fit perfectly in your pocket.
7. Buy wireless headphones
Yes, yes, you can choose and purchase them in our online store - there is more than a choice. By the way, we are preparing an article on how to choose the right wireless headphones - don't miss it. This method is guaranteed to save you the trouble of tangled wires!
Choose the appropriate method, and may this be with you, for example!
The age-old problem of modern man is confused headphones. Do you agree? As often happens, you leave the house and listen to your favorite music, then you enter the subway or somewhere else, neatly putting your headphones in your pocket. And when you want to listen to music again, you get a tangled thing out of your pocket. Until now, many people sincerely do not understand how this misunderstanding in the form of cleverly tangled wires turns out. Let's try together to figure out how to fold the headphones so that they do not break or get confused.
A popular way to roll headphones
For those who are tired of endlessly untangling their headphones, there is an excellent and simple folding technique. Follow the instructions and you will learn how to fold the headphones correctly.
1. Fold the fingers of one hand into a "goat", bending the middle and ring. Stretch the earbuds along your palm, pressing down on the earplugs with your thumb.
2. From the outside of your hand, wrap the wires around your little finger. Then again around the index finger from the inside.
3. Wind like this until the entire length runs out. Leave a small piece from the headphones.
4. With the remaining end, wrap the headphones in the middle of the loops. The loose plug can be hidden in one of the hinges.
5. It is very easy to untie such a knot. Pull the earplugs away from the earbuds and they come loose with ease.
Method number two
If you often wonder how to fold your headphones so they don't break and last longer, follow our instructions. Here is the second winding method:
1. Fold three fingers together tightly.
2. When straightened, start wrapping the headphones around them. Make sure that the wires are not too tight. Otherwise, you run the risk of messing up the connections.
3. When you wind the entire length of the headphones, as in the previous version, wrap them in the middle and hide the plug inside.
Maybe this method is not as aesthetic as the previous one, but it is also quite suitable.
You can wind up any wires in the same way. This will save you space and, well, the time it usually takes to unravel them.
Headphone cases
If you like to keep things in their place, then take a closer look at the headphone cases. At first glance, it seems that this thing is absolutely unnecessary. But only those who know the importance of the issue will be interested in this accessory. In fact, everything is simple and banal. The case is a small wallet made of leather or rubber with a zipper. Thanks to storage in such a case, the headphones do not get confused and are always close at hand.
In addition, a common problem when one earphone does not work is most often associated with improper storage. Wires become tangled, clinging to items in your bag or backpack, and you pull on them to reach them. And this is absolutely impossible to do. By using one of the methods of folding or storing in a case, your headphones will last a long time and will delight you with good sound.
Headphone cases are sold at any store with mobile phones in the cases department. And there is also a huge selection on Chinese sites, where you can always choose exactly what you like.
Now you have learned how to fold the headphones. Good luck!
Tangled headphone wires are a perennial problem for most people who use them. Hurriedly tossing your headphones into your bag or backpack, the rest of the way home, you untangle the wires like a garland. We will tell you about a couple of tricks that will help you avoid this.
Important: to avoid mechanical damage, do not pull the headphone cable too tight.
Roll the wire into a figure eight
1. Fold your hand as if you were throwing a "goat" at a rock concert.
2. Press down on the headphones with your thumb.
3. Wrap the wire around your little finger on the outside of your hand, then around your index finger on the inside.
4. Roll the headphones in this way, leaving a small piece of wire.
5. Tie the coiled headphones in the middle with it.
6. Plug the plug into the loop formed from below.
7. Pull on opposite ends of the earbuds to unwind them.
Wrap the wire around your fingers
The method is not so elegant, but simpler and faster. It was shared by Dieter Bohn of The Verge. Wrap the headphones around three fingers, then tie the rest of the wire in the middle and remove the plug into the loop. In this way, you can wind up not only headphones, but also other cables.
Do you know other convenient ways? Share them in the comments.