Menu
Is free
check in
the main  /  Advice / How to transfer the operating system to another computer. Is it possible to transfer the installed Windows to another computer? We use Acronis True Image WD Edition

How to transfer the operating system to another computer. Is it possible to transfer the installed Windows to another computer? We use Acronis True Image WD Edition

Imagine the situation: you change your motherboard or endure a hard drive with the installed system to a new computer. And of course, on the new hardware, the system does not start. What do many do in such a situation? Reinstall the system. However, there is another way: pre-prepare the system to transfer using the SYSPREP utility.

Starting with Windows Vista Sysprep is part of the operating system.

With SYSPREP, all unique information about the installed system is cleared. Including the information about the installed drivers. At the same time, the programs and user settings are not affected.

Yes, I immediately want to warn - among other things, the activation information is also cleared. After transfer, activate the system will have to re-on. Special attention to those whose Windows has been pre-installed along with the computer (OEM version), after transferring to a new iron to activate the system automatically via the Internet will not work, only by phone. And then may refuse, because OEM license is rigidly tied to the equipment of the computer sold to you.

So, launch Sysprep on the system that is going to transfer. Make it necessary Before transfer. You must use only the version of the SYSPREP, which is installed with Windows.

In the command prompt, open on behalf of the administrator, we perform:

% WINDIR% \\ SYSTEM32 \\ SYSPREP \\ SYSPREP

In the window that opens, we make the following settings:

  • in "System Clearing Action" Select the option "Go to the System Greeting Window (Oobe)" and note the option "Preparation for use";
  • in the "Operating Service" options, select "Completing work". You can select "Restart" if you want to immediately remove the image of an already prepared system disk by booting with DVD or USB. The main thing is not to get boot from the prepared system disk, otherwise the whole process will have to begin again.

After pressing OK, the process of cleaning the system is started, after its end, the computer turns off. Now you can transfer a hard disk to a new system, change your motherboard, etc.

At the beginning of the download, you will see the inscription "Preparation of the system to use", then "Installation of devices is running":


The system can reboot and continue the installation is normal.

In the end, you should see the Regional Settings window (the appearance of this window already indicates that the transfer was successful):


Enter the name of the new user. In order not to confuse the settings of existing users enter a name that has not previously been used (for example, a test). This user can then be removed.


Next, we carry out the standard date and time settings, automatic update, etc. As a result, you will get the test desk test. Now you can make a way out of the system and go under your usual account. Latest barcode - Driver Update.

That's all right. The transfer is carried out quite simple and quickly.

How wide can I change the parameters of the equipment?

Microsoft advises using this technology only for computers with similar configurations (seemingly). Those. This method can not always work. For example, it is completely incomprehensible, what will happen if the image is made on the system from Intel and moved to AMD and vice versa (who will try, write off, please). On the other hand, I created an image on a virtual machine (Virtaul PC 2007) and successfully transferred it to computes with the most different configuration. True, it was all with Intel on Intel.

When buying a new PC, users often ask how to transfer Windows 7 to another computer. This is very relevant, because I really do not want to deprive yourself of all installed programs, accounts and personal files.The fundamental ability to make this operation will help the SYSPREP system utility. It will help prepare the image of the entire system to transfer the new PC. .

That everything came out, it is advisable to make transfer to a compatible architecture. Those. To transfer Windows from the AMD platform to Intel and vice versa may not work. When you transfer the transfer, it is desirable to create a backup image of your system so that in case of unsuccessful transfer to be able to recover from it. Before creating an image, you need to remove all virtual hard disk emulators (Ultraiso, Daemon Tools, etc.)

To begin with, you need to start the command on the command prompt. sLMGR / DLV..

After that, a window will open where you can see the number of Windows transfers to other PCs.

Next step need to enter a command C: \\ Windows \\ System32 \\ sysprep \\ sysprep.exe. This command will open the system utility that will begin to prepare Windows 7 to "deportation" to the new iron.


It is necessary to set everything exactly as in the screenshot from above.

It is necessary to translate the system to mode Oobe.What will ensure the activation of the transfer mode upon subsequent startup system already on new equipment.

You need to put a mark in the field " Preparation for use" This means that the system will remove all the information that the utility will not use to copy, namely (information about activation, security identifiers). All programs must be transferred in full. Next, a window appears on the screen in which the Windows 7 preparation process for transferring to a new computer will appear. This operation will continue for a few minutes, after which the PC will turn off.

The next step should be removed the hard disk from your old PC, carefully dismantling it. After the disk is fixed and connected to a new computer, the PC must be turned on. After that, Windows 7 will start updating the registry configuration and run service. If an error got out, then you need to restart the PC so that the setting starts up again. As a rule, errors occur if there are emulators or antiviruses in the operating system that needs to be transferred. If everything is fine, the system will start installing the devices and apply the configuration parameters.

Next will follow the usual reboot and configure account settings. It is very important to enter a new username. For example, on the old PC was the name Sergey. To avoid conflict in the system when transferring, you need to enter any other name, because This account will be temporary. Next, standard system setup operations are password, time zone, accept license terms. In the window " setting up windows»Select item" postpone the decision" When you first download the system to offer start from multiple accounts. If the old PC was, for example, two accounts, then Windows suggest running from three, including a new one, which was created in the previous paragraph. After downloading, this account can be deleted.

This article describes a proven way to transfer a hard drive with Windows to another computer / laptop in a healthy state and without errors without using any additional software.

If you have acquired a new computer or received a new laptop instead of morally obsolete (a, maybe I have probably had an idea to postpone Windows. That is, transfer a hard drive with Windows to a new assembly. Bypassing the long installing of the Windows itself and the drivers to it, re-install programs, restore accounts and passwords. As it, sometimes, Mouorno ...

If it was Linux, there would be nothing easier. These systems are used to uploading all installed drivers right while the computer is turned on and downloading: That's why they love to put on portable devices so much. Windows does never do it: after installing the system, the drivers are tightly tied to the devices installed in the computer. So, if you try to transfer a hard drive with Windows to an updated assembly just rearring the disc itself, You may encounter a number of problems.

What are the options or proceed to move.

Why can not transfer Windows just like that?

  • First Cause - hal.dll.. He same hardware abstraction level. It is wrong drivers and call BSOD on a computer when you are just going to download the system in new conditions. Windows downloads drivers for old motherboard and chipset. You have already defined the characteristics of the controller of the main storage of the system (then the test of the hard disk). This is also about the graphics processor, they did not mention: when "shift" ATI on the nVIDIA Problems with starting are guaranteed.

You turn on Windows ... And it does not understand what is happening.

Guaranteed options how to transfer windows

They do not exist: 9 chances of 10, which will not work somewhere. It is always dancing with a tambourine. Microsoft itself does not frankly encourage. Although she supplied some opportunities for this corporate client. About this later. So, if the problem of key transfer is not careful, go further.

The most important thing:

While everything works - create and save to another disk standby image image

The first way is "on the ball": removed the disk from the old computer - put on a new

And why not try something? On the old laptop there is a Windows 10, which is no longer pulling. And transfer Windows along with the disk to a new computer. Pull out and fasten to a new place 3.5 inch HDDs can, I think, everything. Once I "repaired" the consequences of such an operation on the example of Windows XP, so all the details are described in the article "". But remember that this method has too many "but". Like that:

  • on both machines CPUs stood from the same office
  • video cards on both assemblies integrated
  • the interface of the connections of hard drives (in principle, this is not a problem, but ...) would be the same
  • etc. etc.

Guarantees, in general, no. Most likely, you will see a bsod or a circular Windows reboot. The item with updating drivers to the hard disk before dismantling in the article is key. Do not miss it.

Method Second - System Preparation Tool

But this is quite the official option. Sysprep. - Powerful tool in Windows, allowing you to prepare a hard disk to move to a new assembly. Yes, so that all programs installed in addition to Windows worked. This option is recommended when:

  • hard disk from the old computer is transferred to a new assembly
  • the old computer changes the motherboard and / or processor (or even together, including graphic GPUs)

In this case, the installed Windows, programs for it and user profiles will remain in their places. However, this method has small assumptions (more - in the link under the article about the utility):

  • in fact, this is a new installation of Windows; The initial setting process will need to be updated under the name of the new user.
  • windows activation flies in any case; If you value her, the output is one - the call to the activation service
  • the method on RAID arrays of the combined disks does not roll (I never succeeded)
  • updated Windows via the network (for example, with Windows 7 on Windows 10, with Home on the Maximum) It is also often not amenable to moving: sysprep. it's not gonna go
  • if used - sysprep. It will not help

How to transfer a hard disk with Windows: Disc leave, the rest is changed

This situation can be represented as:

  • we are changing the motherboard, probably a video card (I do not take the bar of operational memory permissive, the power supply will not affect the change)
  • on the contrary, remove the hard disk and put on another computer

Nothing will change and will remain as it was?

Not. Here is a list of changes that you will encounter.

  • all the dots of the system restore are rubbing - they will disappear and sysprep. not working with them
  • logs of events are deleted
  • disable (if activated)
  • all special personalization settings are disconnected, including in the taskbar, etc.

We start moving. This paragraph moves the disk with the installed Windows 10.

% Windir% \\ System32 \\ sysprep \\ sysprep.exe
  • in the window Preparation programs systems Set the parameters and prepare the computer to tripping:

  • run the utility button OK (No other programs run!)

  • if you have not seen, the computer must turn off. This means that it is time to take a scolder and remove the hard drive.
  • We collect a new configuration (and again - only input devices: no flash drives or additional disks). Our task is to boot the system on the "new" disk to but) BIOS "used to" to new equipment and b) The system was determined with new parameters. Now you will see the window (did not see the error again? - You are on the link with errors Sysprep.), in which the system is as if setting the system (as for the first time); And everything is honest - with passwords, new username (former your account will remain untouched)

  • You will see the desktop, check the device manager for properly installed hardware. , if required. After this turn off the computer:

device dispatchers: On the left on the old assembly, on the right - on the new one; You only have to "set up" a video card

  • Install the desired devices in the ports and connect additional disks if necessary. Turn on the computer and check if necessary repeating the procedure for installing drivers.
  • If after installing Windows on the screen welcome you meet you only a new accountmake it display everything Accounts. To do this, use Article "".

to the former user 1 After the transfer joined 123

From myself I will add that this way to transfer a hard disk with Windows I was tested many times and the failures almost did not give. However, sometimes it makes sense to make the installation of Windows completely.

In case of replacing or buying a new computer or laptop, when replacing your motherboard, you will have to either install the system from scratch or use the method of transferring all data and installed programs using the utility Sysprep.. This is a built-in Microsoft utility to help the user prepare your system to transfer to a new iron without rearranging the operating system.

When starting sysprep. Your operating system clears all the information about the installed, also resets the unique information about the installed OS. The main thing is that you are interested in users in this method that all data and installed programs will remain not touched. That is, you will not have to make backup, and on the new install all the software on the computer. Microsoft warns that in addition to information about drivers and devices, information about activating your Windows will be lost, so you have to activate your licensed Winodos 7 or by phone, or via the Internet (OEM exception). OEM version binds activation to the gland, so it can be made only by phone.

We begin to prepare our OS to transfer.
To do this, launch (already installed) utility sysprep. On the computer using the command (on the command line on behalf of the administrator, we enter a string (Start - Run - CMD)):

% WINDIR% \\ SYSTEM32 \\ SYSPREP \\ SYSPREP

A window must open with the settings of the utility with the following items and settings:

In point System cleaning action Choose Switching to System Welcome Window (Oobe) And put a tick Preparation with use.
In parameter completion of work Select item Completion of work. You can choose and restart the system if you want to remove the image of this system booting with a DVD or flash drive.
Do not load after the SYSPREP procedure on the same computer, because it will have to reinstall this procedure before transferring to a new PC.

Press OK. And we wait until the system is shown in the initial view. After the process is completed, the computer will turn off. Now you can change the motherboard on the computer, or transfer to a new computer.

When you start the Windows 7 operating system, you will install and define devices.


It may be possible to restart the system (this is a normal phenomenon) Well, at the end of the installation, you will need to select a language and configure regional parameters.


Introduce the dates, standard settings, automatic system update mode, etc.
At the end of the installation, enter the system under the user, complete the session and you can go under your account under which you have always worked. It remains to adjust the new drivers and work in normal mode on the computer.


Transferring Windows 7 with installed programs is not such a complex procedure that is carried out using the SYSPREP utility much faster than the complete setting from scratch. But there are also their nuances in this method. Microsoft does not guarantee 100% of the operation of this method when transferring, for example, different chipsets, such as Intel on AMD or vice versa. But in practice there were cases that the system was raised and worked without failures. If you transfer with similar models and chipsets, most likely there should be no problems and conflicts.

Good afternoon, please tell mehow to transfer Windows to another hard drive Without reinstalling the operating system. I explain my situation: My Windows 8 is located on the 250 GB-divided "Badast" Winchester section of 250 GB, is it possible to move the system with all the installed programs to a new hard disk with a volume of 400 GB, but it is unfortunately not empty, it is already alone on it The section with the volume of 100 GB and with them nothing should happen. Alexander.

Hi friends. Let's help our reader and at the same time! I also have an old rigid diskMaxstor Volume 250 GB with installed Windows 8.1 and I have long wanted to transfer it to another hard driveSamsung (400 GB volume), there are also files on this Winchester. By the way, if you transfer the operating system, then it is better for, that's where everything will earn it faster.

We will work with Acronis True Image with you and you will need Acronis Disk Director. The operating system in our case can be any, for example Windows 7, 8, 8.1, 10. The entire transfer process is described in our article step by step and I think you will succeed.

You may be useful to you and our other articles on this topic:

  1. Similar article, only the tool is applied - cloning. .
  2. Very simple article, where we are also doing the same with the help of a free program Aomei Partition Assistant, i recommend it to all novice users -
  3. If you have a laptop, you may use articles .
  4. If you are interested in an article, visit the special section where they are collected from one information drive to another.

Window Disc Controls

So, we have two hard drives:

Disc 0. Hard disk samsung (400 GB) with one section. With this disk everything is clear, there is one section on it and there are 100 GB data, with which nothing should happen. It will be transferred to it from the operating system from the MaxTor hard disk or disk 1.

Disk 1. Hard disk Maxtor The volume of 250 GB with three sections.

The first section is hidden and has no letters, called System Reserved (reserved by the system), the amount of 350 MB, the main purpose of the hidden partition is to store Windows 7 or Windows 8 downloads. We will carry it.When transferring operating systems, this section with Windows loading files must be included in the backup.

The second section under the letter (C :) Volume 105.00 GB installed Windows 8.1 operating system on it. We will carry too.

The third section under the letter (D :) Volume of 127.00 GB with user data. We will not carry.

Acronis Disk Director.

First of all, load from the boot disk or boot flash driveAcronis Disk Director and separated from a hard disk Samsung (400 GB volume) 130 GB space specifically forWindows 8.1, which will be transferred to it withMaxtor.

Select the left mouse with the WinchesterSUsung Space (400 GB) and choose Resize Toma

We cling to the mouse of the delimiter and pull it from left to right, thereby "biting" from the SAMSUNG Winchester space 130 GB for the future operating system.

we release unoccupied space 130 GB necessarily at the beginning Toma . At the bottom of the window, we see the future state of sections on the hard disk. Click OK.

Program Acronis Disk Director.works in a deferred operation mode. So that we have come true, you need to press the button Apply

Proceed

The first task is made. On the Samsung disk using the Acronis Disk Director program, we have created a unallocated space of 130 GB for the future Windows 8.1.

Acronis True Image.

Creation of backup

Now we work with the Acronis True Image program. In this program, we need to create a Windows 8.1 operating system backup located on the Maxtor rigid disk and deploy this backup to the unallocated SAMSUNG disk space.

Also load the computer from the boot disk Acronis True Image. In the initial program window, choose

Backup. Disks.

Window archived sections.

In this window we need to choose Disk 1. Sections for archiving.

In the window that appears, you see three disks:

Disk 1.. Boot flash drive With Acronis True Image.

Disc 2.. Hard disk samsung400 GB which will carry Windows 8.1.

Disc 3.. Hard disk MAXTOR.250 GB (from which to transfer Windows 8.1). To turn on the backup, mark the hidden section System Reserved (reserved by the system), the volume of 350 MB, the main purpose of the hidden partition is to store Windows 7 or Windows load files. When transferring operating systems, this section with Windows download files must be included in the backup. Acronis assigned to him a disk (G :), in the operating system itself, this section does not have and see it only in drive control.

I also celebrate the section with the Windows 8.1 operating system itself, here it has a letter (C :). You may have another letter. Weiently focus on volume volume. Further.

Overview

Here, we select the Samsung disc for the storage of the future backup under the letter (F :) the volume of 400 GB in the left part of the window, the files are displayed on it.

Proceed

Windows 8.1 backup occurs, on the only existing section of the samsung hard disk.

Turn off the computer and disconnect the old hard driveMaxstor The volume of 250 GB and leave one hard drive in the systemSamsung, make it necessary! After transferring the operating system, the MAXSTOR rigid disk can be connected back.

Acronis True Image.

Deploy backup with Windows 8.1 on hard diskSamsung

Now there is one SAMSUNG hard disk in the system unit (volume of 400 GB), on this Winchester is one section with data and it is on this section that there is a backup with Windows 8.1, also at the beginning of this section created a unallocated space, it is for this space that we will unfold Bacup with the operating system.

Again, load from the boot disk of the Acronis True Image and choose Restoration. Disks. Files and folders.

We find our backup on the section (C :) SAMSUNG hard disk. We highlight it with the left mouse once and click OK

Click on the button New storage

Celebrate Unmounted space On our samsung hard disk and click on the Accept button

I click on the button New storage

We click on Unmounted space and To accept

Select the target disk to restore MBR. We mark the SAMSUNG disk 2 (400 GB). We celebrate the checkbox Restore disc signature and Further.

Proceed

Program Acronis True Image unfolds Windows 8.1 operating system backup to a predetermined samsung hard disk space created by us. In essence, the operating system is transferred to another hard drive.

OK and reboot the computer.

Friends if you have in the system unit there are still connected hard drives, but you need to enter your computer's boot menu and select the hard drive to which you transferred Windows, in my case, this is a samsung hard disk.

After downloading, we go to drive control and see such a picture.

1. The hidden section of the System Reserved hidden section was transferred to the SMSUsung hard disk (reserved by the system), 350 MB with Windows 8.1 download files.

2. Also transferred to Windows 8.1 itself and is under the letter (C :).

3. With the 100 GB files, nothing bad happened, only from this section.

4. There is still a unallocated area and we will connect it to the disk (C :).

That's all

Now you can connect the old hard disk to the computer.Maxstor and you will use our article -