What heating element is better in the washing machine. TEN for a washing machine: how to choose a new one and independently replace

From the very beginning of SMA was created with the calculation that they would be able to do all cases associated with the washing and drying - to do themselves. And therefore, it is clearly the fact that without a heating element it did not cost it. Because, if not he, then who could organize water heating to the desired temperature? And the drying of the linen as without it possible would be? And that's why Ten is necessarily present in the automatic machines - one of the most important details of washing machinery.

Ten of washing machines and their device

From the very beginning it must be said that if SM "knows" and warm water, and drying the linen, it means that it has two heating elements. TEN, which is designed to heat water - is installed at the bottom of the tank, whereas for the organization of drying - a TEN is used in the so-called "drying chamber".

TEN for washing machine - This is a tubular heater (electro) capable of converting electrical energy into thermal. Once the washing machine is connected to the power grid, it is in its heating device (or rather along the electrical spiral inside the device pressed into the stainless tube together with quartz sand) passes electricity, heating water to the desired temperature. And the connection of the Tan itself occurs at the expense of the terminals performed by the type of plates under contact clips. There are still terminals and threads - it all depends on the model of the washing machine.

By the way, the electric spiral, arranged, inside the stainless tube, is made of thermoelectric alloy, which makes it possible to carry out not only long-term load, but also short overload time (this may be due to electric voltage jumps). If we talk about the place of fastening the heating device, it turns out that there is necessarily the presence of a sealing plastic gasket.

Constructive features of Tan machine machines

It will not hurt to know that the beans for heating water are similar in their design, but may have differences from different factors: power, length, heating element bending angle, terminal location, presence / position of the hole for temperature sensor. Here are all these parameters and wonder.

If you start a comparison with power, then we learn what: the most economical heating devices consume power within 800 W, and the most voracious - up to 3000 watts. Speaking about the length of the Tan, then we must specify that they can be long, short and medium in length. So a short TEN is a heating part, ranging from 15 cm, and the longest - within 30 cm. As mentioned above, the tens of washing machine machines and the bending of the heating element differ. If the form, as a rule, everyone has a spiral-shaped, then the angle of their bending can range from 15 to 45 degrees (there are separate species that have even exceeding the specified parameter).

There is a difference and terminals: standard models have on each side by one terminal, and in such mothers, as, for example, Bosch - two for each side.

It is worth indicating that there is such a difference as a TEN for a metal tank and a tan for plastic. For iron tags, heating devices are made with a rubber band in length about 1.5 cm (or even less), and for a tank of plastic - more than the specified parameter. And all because the plastic tank has thicker walls.

Do not go through such distinctive featureCooney is special. Hole for the sensor. If it is provided, then located in the metal base of the Tan. It should be understood that if you suddenly need to purchase a new heating element, it is necessary to take into account this feature - buy only a tan with a hole under the sensor.

Water as the main factor against the Tan Teni are in contact with water - it goes without saying, therefore it is not surprising that their breakdown happens primarily due to the appearance of scale. It is akin to scale in the kettle, only here everything is more serious and in a larger volume, because it is a "bouquet" from different unwanted impurities. When the limit of "tolerance" of the heating device comes, then he reports this to its owners like this: the heating ability decreases, the electricity and powder and powder takes place, the laundry does not shine perfect cleanliness. In general, everything becomes not as it was before.

If all these signals are disregarding and continuing operation, then huge global closures are possible - the breakdown of other important parts of the machine machine and its full failure. So that this is not happening, try to turn to the masters in a timely manner, the repair service of which is at the highest level for the knowledge of the problems not only by CM, but also other household appliances.

SMA heater service life

Under normal operation, the service life of the TEN can be from 5 to 10 years. But if you create adverse moments, it will fail before the first period of the first term. And what can provoke such an output? It:

• Production quality of the smart and details to it;
• The frequency and temperature of washing;
• Hardness of water.

But more nevertheless, the "life" machine machine, as well as its parts depends on the quality. And if you want to always be confident that any appliances Only from a recognized manufacturer, then not be lazy to acquire it in specialized centers. Such stores can provide all guarantees on their products, as well as help with the choice of any spare parts, accessories and installation fittings.

TEN - tubular electric heater. In the washing machine is responsible for heating water. Works "paired" with a thermal sensor, which is most often installed in the heater itself. If the washing machine ceased to warm the water - one of the reasons may be the failure of the heating element. In the catalog of our online store there is more than 50 models of Tan on all brands of automatic washing machines (Bosch, Indesit, Ariston, Zanussi, Electrolux, Beko, LG, Candy and others). All products of European brands production: CEBI, THERMOWATT, IRCA, BLECKMANN. Prices from 590 rubles.

How to choose a TEN.

The main criteria for choosing a Tan washing machine are:

• power: from 1500 to 3000 watts. The most common are the models per 1800-2000 watts. When replacing it is allowed to install a heater with a power of +/- 100 watts from the original.
• tan Length: from 160 to 300 mm. Most washing machines are installed heaters for 200 or 240 millimeters.
• the presence of a hole for the thermal sensor: The temperature sensor can be installed directly in the tane (in this case, a hole with a diameter of 12 mm is made on the floor of the TEN), or in the washing machine tank.

Replacing the heating element of the washing machine

How to choose a TEN (heating element) for washing machines s on a brand of technology ...

1. Landing place

The main thing in the selection of Tan - to fit the seat. Fortunately, almost everyone TENobsite this place is the same. And amounts to: the width of the gum is about - 7cm, the height (thickness) is about 1.5-2Cm. (Depends on the thickness of the gum). The exceptions are Tan on the old washing machines ah, which are more than 12 - 13 years old ...

2. Availability of rubber on a rubber band

The presence of a fifth on the rubber band - preferably consider. If instead of a Tan, who has there was no side, put a tan with a boom, but maybe not to get a rubber band - up to fasteners ... as a result - Ten can fly out of the tank during washing. In principle, you can put a tan without a boil, in place of the Tan with a boom, but not desirable ... Although the masters are doing, but they are also replaced by a coin) and so focus on the length of the gum itself (after the side).

3. Hole under the sensor in the flange

On some tanks there is a special hole for the sensor. On all thenesses running with the sensor, this sensor can always be pulled out, even if it seems that it is smeared. (As far as I know except Tanov - Kawai)
Instead of a tan without a hole, you can put a tan with a hole using a special plug. (Well or coin - 50kop. or 1 ruble)
(On the washing machines, Ah LG-SAMSUNG there are models on which there are tannes with a sensor, but nothing connects to the sensor. In this case, you can put a tan without a hole.)

4. Length of Tan

After there is a difference in length. Tanes are short, medium and long. It is advisable to consider the length, but if the new tan is a little longer or shorter than the old one, then nothing terrible. You can also put a short Ten instead of a long, but long TEN is not suitable for a short place (may not fit).

5. Power of Tan in Watt (W)

Then there is power. The power value does not have. And it happens from 800 to 3000 W. If the Ten is more powerful, then it will heat the water, it will be a little faster, and if less powerful, then heated will be a little longer. The difference will not be noticeable. But it is desirable that the power of the Tan did not differ over 150-200 W

6. Form of Tan

Another point in the selection of Tan is his The formand Bend. Almost all the fan are straight, but sometimes curved are encountered. Usually, the bending is exactly necessary to take into account.

7. Tan coating

On some models of washing machines are tagged with ceramic or other coating. It does not have a fundamental value, it may be a little longer.

8. Manufacturers of Tanov

THERMOWATT (best in quality, on these lanes knocked out "Made in Italy")
IRCA (second quality, but these fuses go with the fuse)
Blackmann (more worse thans, found very rarely)
The manufacturer does not matter, the main TEN to suit other parameters.

The process of selection by brands

Samsung, Indesit, Ariston - Short Tanes with a hole, without a boil. In some Samsunga, ceramic tanes are put. Instead, it is possible to put ordinary short tans with a hole.
LG - short tanes without hole. Some models come with Tanni with sensors.
Bosch, Siemens - medium tanks with boom, with hole.
Candy - Long Tanes without a hole, with boom.
Electrolux, Zanussi - Long Tanes with a hole, with a burt.
Ardo - Sometimes there are curved lands with a hole or without it.
On the old models of the above stamps can be other lanes. Basically, long lands were put on. There may also be or not to be a hole under the sensor.
This list is approximate. Possible discrepancies!

We offer to buy original Italian tans for the washing machines of Thermowatt and IRCA on the best prices. A large assortment that is constantly increasing high quality, proven by time and satisfied buyers. We can offer both the original and analogue in the absence of the latter.

Tanners of our catalog will suit almost all models of firms produced washing machines, such as: Candy, Ardo, Indesit, Samsung, LG, Ariston, Beko, Siltal, Bosch, Electrolux, Whirlpool, Kaiser, Gorenje, Siemens, Zanussi, Aeg, Miele.

Features and Description of the Tan for washing machines

TEN - a tubular electric heater serves to heat the water in the washing machine. Tanes for washing machines differ in power, shape, width of the flange, the presence of a hole for the thermal sensor. Mostly flanges have a length of 80 mm and a width of 25 mm, but there are beans with flanges with a width of 28 mm. Tennes with a wide rubber band (more than 1.5 cm) are suitable for plastic tanks, because Their walls are thicker. Tenny with a rubber band up to 1.5 cm - for metal tanks. The main thing when choosing a heating element take into account the size. You can take a smaller tank, it may not come true. You can take a greater or less power, just water will be faster or slower to heat.

Tanes in the washer are consumable. And accept the fact that the replacement of the heating element in the washing machine is often frequent and irreversible. In this article we will respond to three Fa questions: what is the reason for the heater breakdown in washing machineHow to understand that the TEN is damaged, how to choose the heating element correctly.

The reasons for the failure of the Tan in the washing machine

Teni break, because they are throwing out. Did you look into the kettle? We noticed how the metal bottom is covered with reddish-gray solid sediments? The same thing happens with the heater in the washing machine. The heating element is working in aggressive conditions and performs thousands of heating cycles. It is quite natural its wear. And you do not need to kick producers, since water from the water pipeline. Although S. toit notice: even distilled water issues a precipitate after boiling.

Symptoms of the heater breakdown in the washer

Once the Ten overheats and fails. What happens at the external level? A person with a susceptible nose is learning the smell of Gary. And the one whose nose is not so sensitive, putting a hand to the "Illuminator", notes that the glass is cold, although the washing mode with a high temperature is set.

Tan selection rules for washing machine

• Power

Where to see the power of the heater? - on the landing place of the Tan next to the connector for the temperature sensor.

Some experts believe that the power during the selection of the Tan in the washing machine does not matter much. The tan with higher power rates warm the water is slightly faster, and the one who has a W indicator below is slower. There is no significant difference.

• Planting

In some models of eraklok, there is a special hole for a temperature sensor, there is no one in others. If the car was stood with a heater without a hole, then it can be replaced with a similar element with a hole. "Pull up" the unsuitable hole can be a special plug.

In the washing machines of the LG trading brand there are models on which there are beans with a sensor. But the sensor is not connected to the contact group. In this case, you can take the heater without a hole.

• Length of Tan

Teni can be divided into small, medium and long.

The size of the heater is important to consider. Make a larger TEN - and the spare part will touch the walls of the tank during operation. But instead of a long tan, you can put short.

• Heater shape and coating

Among the diversity of direct shades, you will be stumbled upon curved heating elements. Therefore, we take into account this parameter.

Typically, the part is covered with a layer of stainless steel. But there are beans with a ceramic shell, which longer opposes the destructive power of scale.

• Manufacturers

Most often there are heaters from thermowatt. These are leaders in quality. "Made in Italy" are knocked on them. Heaters K. washing machines Thermowatt can be ordered in the catalog.

The second quality is the heaters from IRCA.

Blackmann - Tanni from these manufacturers should not be purchased (enjoying bad glory).

Choosing a Tan on the trading brand

SAMSUNG, INDESIIT, ARISTON, usually go to the temperature sensor with a hole under the temperature sensor.

A short heaters with a hole or without it are suitable for LG.

Bosch machines, Siemens - elements of medium length with a hole.

For Candy serve long lane without a hole.

The ELECTROLUX, Zanussi will be perfectly in size with a place for a temperature sensor.

For ARDO washing - in the models of this brand there are curved lands with a hole or without it.