1. Press the button and select "".

2. Press the button and set the temperature to 32 ° C.

3. Click the button.

· The airflow rate will be set automatically.

· This operation should be carried out when the air temperature in the room does not exceed 28 ° C.

2. Clean the air filters and replace them.

3. Remove the batteries from the remote remote control.

4. Turn off the air conditioner.

Regular air conditioner maintenance

Under some conditions, the internal surfaces of the air conditioner may become heavily soiled as a result of operating the air conditioner for several seasons, which leads to a deterioration in its performance. Therefore, in addition to regular maintenance of the air conditioner, we recommend that you call in a specialist from time to time to have it checked. For this purpose, it is necessary to contact the representatives of the company from which the air conditioner was purchased.

FAULT DIAGNOSTICS

Signs not indicative of breakage

The situations listed below are not related to a malfunction or breakdown of the air conditioner, but have other reasons. Therefore, in these cases, the operation of the air conditioner can be continued.

Symptom

Cause

The air conditioner does not start working immediately.

· The power button was pressed shortly after the air conditioner was turned off.

· A new operating mode has been selected.

· The start-up delay serves to protect the air conditioner. Wait about 3 minutes.

The air conditioner does not start heating immediately after switching on warm air into the room.

· The heat exchanger of the air conditioner is warming up. Wait 1 to 4 minutes. (Air supply to the room starts only after it reaches a certain temperature.)

Heating operation stops, and the sound of liquid flowing from the air conditioner is heard.

· The system has automatically entered the defrosting mode of the outdoor unit. Wait 3 to 8 minutes.

Water dripping or steam escaping from the outdoor unit

n In Heating Mode:

· When defrosting, ice melts and forms water or steam.

n In Cooling or Drying mode:

Light mist comes out of the indoor unit.

· In cooling mode, moisture contained in the air condenses and is carried out in the form of a mist from the air conditioner by the cold air flow.

You smell from the indoor unit.

· Smells from furniture, tobacco smoke, etc. are absorbed by the indoor unit and then blown into the room. (In such cases, it is recommended to contact a specialist who will wash the interior surfaces of the air conditioner.

The fan of the outdoor unit rotates although the air conditioner does not operate

n Immediately after turning off the air conditioner:

· The fan of the outdoor unit must rotate within 30 seconds after being turned off.

n When the air conditioner was not working long time:

· When the air temperature is high, the fan of the outdoor unit will start automatically to avoid damage to the system.

The air conditioner operation stops suddenly (but the OPERATION lamp is on)

· The system may automatically shut down when the supply voltage fluctuates greatly. It will turn on again after about 3 minutes.

Checks prior to calling a specialist

Before contacting an air conditioner repair and maintenance technician, perform the following checks again.

Symptom

Examination

The air conditioner does not work (the OPERATION lamp is off)

· Is the circuit breaker tripped? Is the fuse blown?

· Is there a power outage?

· Are batteries inserted in the remote control?

· Is the address switch of the remote controller set to the correct position? (See section Preparing the air conditioner for work.)

Is the timer time set correctly?

Cooling or heating is insufficient

· Are the room temperature set from the keypad correct?

· Are windows and doors closed?

Are the airflow speed and direction adjusted correctly?

Air conditioner operation stops suddenly (OPERATION lamp blinks)

· Are the air filters dirty?

· Are there any obstructions for air entering or leaving the outdoor and indoor units?

Clean air filters or remove obstructions. Turn off the power at the circuit breaker and then turn it back on. Then try starting the air conditioner with the remote control. If the OPERATION lamp continues to flash, call the specialist from the company that sold you the air conditioner.

Air conditioner malfunctions

Air conditioner malfunctions may be caused by lightning strikes or strong radio waves. Turn off the power and then turn it back on. Then try starting the air conditioner with the remote control.

Cases requiring an immediate call of a specialist

Dangerous!

n If anything suspicious happens to the operating air conditioner, such as a burning smell, turn off the air conditioner and turn off the power.

Continued operation of the air conditioner in such cases may lead to serious consequences - electric shock or fire.

n Do not attempt to repair or alter the air conditioner yourself.

Otherwise, this may result in electric shock or fire.

Contact the representative of the company that sold you the air conditioner.

In the following cases, call an air conditioning specialist immediately.

n The power cable is overheating or damaged.

n Unusual sounds are heard from the air conditioner.

n Circuit breaker trips frequently, blown fuse or earth leakage device trips.

n Switches or control buttons do not work.

n The smell of burning is felt.

n Water flows out of the indoor unit.

Press the OFF button and call the service department

n After a power failure:

wait for about 3 minutes and the air conditioner will automatically resume operation.

n During a thunderstorm:

If there is a possibility of lightning strike, turn off the air conditioner and turn off the power. This will protect the device from damage.

qualified specialists.

Under some conditions, using the air conditioner for several seasons may cause the inside surfaces of the air conditioner to become heavily soiled, resulting in a deterioration in the performance of the unit. Therefore, in addition to regular maintenance of the air conditioner, we recommend that you call a specialist from time to time to have it checked. For this purpose, it is necessary to contact the representatives of the company from which the air conditioner was purchased. In this case, the owner shall bear the costs of servicing the air conditioner.

Diagnostics of malfunctions by the control panel.

Description

Description

Siste- ma

Fine

Outdoor unit

Compressor overload

Low system pressure

Blocking, overloading the compressor motor

Low mains voltage

Input voltage sensor blocked

Switching error between blocks

Outdoor temperature sensor failure

Inside- renny block

Heat exchanger malfunction

Heat exchanger does not work (Th2 - thermo sensor)

Motor blocking due to overload

Gas pipe thermistor defective

C4 0R C5

Heat exchanger does not work

Increasing the temperature of the radiator of the power transistor

Intake air thermistor does not work

Power transistor radiator thermistor malfunction

Instructions on the following model:

Daikin FTX20JV / RX20JV

Air conditioner Daikin FTX20JV / RX20JV

Table of contents
Disposal
Name of each part
Preparation before starting work
Selection of operating modes
Additional modes and settings
Useful Tips
Cleaning your air conditioner
If you think there is a problem
When will not be used for a long time (At the end of the season of use)
Installation site and electrical work
Precautionary measures

Disposal
Recyclable materials have been used to make this device. Therefore, check with your local authority on how to properly dispose of it in your area.

Name of each part
Outdoor unit

1 - Air intake is carried out on the rear and side surfaces.
2 - Air outlet on the front surface, behind the grill there is a fan and a heat exchanger.

Indoor unit

1 - Air intake to the indoor unit.
2 - Window for receiving commands, indicator lights.
3 - Air discharge from the indoor unit.

Remote control

1 - Start power saving mode.
2 - TURBO fan mode.
3 - Setting the desired temperature.
4 - Selection of the operating mode.
5 - Switching fan operating modes.
6 - Switching on / off the device.
7 - Position of the partition.
8 - Start the comfort mode.
9 - Timer control buttons (on-off, setting the time, resetting the timer, resetting all settings).

Preparation before starting work
The installation and connection of the device must be carried out by specialists with experience in the relevant work.
Install batteries in the remote control.
Connect the air conditioner to the power supply through a socket of the required rating, with grounding.
Make sure there are no obstacles to air movement around the indoor and outdoor units.

Selection of operating modes
The Daikin FTX20JV / RX20JV air conditioner model supports the following operating modes:
auto selection;
heating;
cooling;
drainage;
ventilation.
In auto select mode, the air conditioner maintains the temperature within the limits you specified. If it gets colder, heating turns on, if it gets warmer, cooling.
Heating mode is suitable during cooler seasons. Keep in mind that in this mode freezing of the outdoor unit is possible, so the operation will periodically pause (no more than 10 minutes) to defrost the outdoor unit. In addition, the fan may not start immediately after pressing a button on the remote control. This is how the protection against blowing cold air works - first the heat exchanger heats up, and only then the fan turns on.
In cooling mode, the air conditioner cools the air and dehumidifies. The temperature is maintained at the level you specified.
In dehumidification mode, the electronics work in such a way as to remove moisture from the air while minimally affecting the room temperature.
In ventilation mode, air circulation throughout the room is maintained.

Additional modes and settings
For more efficient cooling and heating of the room, you can use the TURBO fan operation.
For work at night, the Sleep mode is provided. The air conditioner is quieter in it.
To save energy, the Econocool mode is provided. In this mode, the air conditioner consumes less energy.
Automatic restart. If the air conditioner worked in any mode and there was a power outage, then after the appearance of energy in the network, the operation will automatically continue in the same mode.
Timer - to start and stop the operation of the air conditioner on a schedule, it is possible to configure the start and stop at a specific time.

Useful Tips
Do not overcool the room. This leads to waste of energy and can harm your health.
Close blinds and curtains in the room to prevent sunlight from heating objects.
A large number of people and working heating devices can also complicate the operation of the air conditioner.
It is necessary to monitor the position of the vertical damper. It should be vertical when heated, and horizontal when cooled.
Keep the air filter clean. A dirty filter will interfere with the operation of the air conditioner.
Keep windows and doors closed during cooling. Do not forget to periodically ventilate the room - the air conditioner cools, but does not renew the air.
At the beginning of work, in order to cool the room faster, it is recommended to turn on the TURBO fan operation mode.
Cleaning your air conditioner
Do not touch metal parts with bare hands. Unplug the air conditioner with dry and clean hands before cleaning.
Use only detergents previously dissolved in water.
Do not use abrasive detergents, gasoline, thinners, hot water. All this can hurt appearance plastic.

If you think there is a problem
The air conditioner does not work. Check if the plug is connected to the outlet. Is there power on the network. Has the shutdown timer turned off the air conditioner?
Cannot turn on the air conditioner for 3 minutes after turning it off. This is protection against frequent launches. Wait 3 minutes and try again.
During drying, the indoor fan turns off. During operation in this mode, the electronics ensures that the minimum cooling of the air occurs when the room is dehumidified. Also, it is necessary to drain condensate from the core.
During heating operation, the indoor unit stops (maximum 10 minutes). This is necessary to defrost the outdoor unit, which is covered with ice in this mode.
When heating mode is started, the indoor unit does not start working immediately. First, the heat exchanger warms up, and then the fan turns on - this protects you from being blown over by cold air.
After the appearance of power in the mains, the air conditioner began to work, although no one controlled it from the remote control. If the air conditioner was operating in any mode before the emergency power cut, then after the power supply appears, it will automatically resume operation in the same mode.
Water flows from the outdoor unit. During cooling and heating, the air conditioner contains elements colder than the environment. Condensation may form on them. If ice appears on the outdoor unit while heating the room, water will appear during defrosting.
White smoke is coming out of the outdoor unit. During heating, the air conditioner removes cold air outside, around which fog can form.
The image on the remote control has become worse, disappeared, the remote control does not work. Check the presence and correct installation of batteries. Replace them if necessary.
The room cannot be heated / cooled properly. This can be due to a number of reasons. Check if the operating mode is selected correctly, the power of the fan. Are the windows and doors in the room closed, are there any heating devices working? If there are a lot of people in the room, the cooling work will be slower. Is there dirt on the air filters?
The air coming out of the air conditioner has a strange smell. Are the air filters clean? Is there any contamination inside the air cavity? The smell may be drawn in from the outside, such as from a carpet or wall. This is especially possible when condensation gets on them and mold growth.
A crackling sound is heard when the air conditioner is operating. Fluctuations in temperature cause the plastic to resize and crackle.
A splash, gurgling is heard. This is possible with the movement of refrigerant, condensate. If the air conditioner is turned off, and there are sounds, then it is possible that this is due to the operation of the exhaust ventilation - air will flow into the room through the condensate drain hose.

When the air conditioner will not be used for a long time
If you plan on not using the conditioner for a while, it is recommended to prepare it for this.
Turn it on in heating mode. This will dry out the indoor unit and stop the growth of fungi and bacteria.
Disconnect the plug from the outlet.
Remove the batteries from the remote control.
For use after a long period of non-use it is necessary:
make sure that there are no obstacles to air movement around both blocks;
install batteries in the remote control;
connect the plug to an outlet of the appropriate rating;
check for grounding;

Installation site and electrical work
Installation work should be carried out by specialists with experience in this work.
Do not install the device in places where there is a lot of engine oil, salty humid climate, hydrogen sulfide or flammable gases in the atmosphere.
Do not place the air conditioner near high frequency equipment.
Do not place the device where the air outlet will be blocked.

Precautionary measures
Do not connect the device to a carrier, extension cord, or an outlet with an inadequate capacity.
It is forbidden to modify, change, repair the power wire, etc.
Do not place heavy, hard, hot objects on the power cord, do not place foreign objects on the indoor and outdoor units.
Do not pull out the plug from the outlet while the air conditioner is running. Disconnect it with the remote first.
Do not expose people, animals and plants to long-term exposure to the flow of cold air - this can harm your health.
Do not insert fingers, pencils or other objects into the technological openings of the air conditioner cabinet. This is fraught with injury.
If during the operation of the air conditioner an abnormality is detected, such as unusual noise, smell of burning, stop its operation, disconnect the plug from the outlet and call for technical assistance.
If the air conditioner stops heating and cooling, then you need to make sure that there is no refrigerant leakage. Call specialists.
Do not spray flammable substances on the indoor and outdoor units, as this may cause a fire.
Do not place electrical appliances and furniture under the indoor unit - condensation may form, which will damage the property.
Always clean the appliance with the plug unplugged.
Ventilate the room regularly as the air conditioner does not renew the air, but only cools / heats it.
Unplug the air conditioner during thunderstorms.
Ground the device properly.

Daikin FTX20JV / RX20JV

Table of contents
Disposal
Name of each part

Selection of operating modes

Useful Tips
Cleaning your air conditioner

When the air conditioner will not be used for a long time (At the end of the season of use)

Precautionary measures

Disposal
Recyclable materials have been used to make this device. Therefore, check with your local authority on how to properly dispose of it in your area.

Name of each part
Outdoor unit

1 - Air intake is carried out on the rear and side surfaces.
2 - Air outlet on the front surface, behind the grill there is a fan and a heat exchanger.

Indoor unit

1 - Air intake to the indoor unit.
2 - Window for receiving commands, indicator lights.
3 - Air discharge from the indoor unit.

Remote control

1 - Start power saving mode.
2 - TURBO fan mode.
3 - Setting the desired temperature.
4 - Selection of the operating mode.
5 - Switching fan operating modes.
6 - Switching on / off the device.
7 - Position of the partition.
8 - Start the comfort mode.
9 - Timer control buttons (on-off, setting the time, resetting the timer, resetting all settings).

Preparation before starting work
The installation and connection of the device must be carried out by specialists with experience in the relevant work.
Install batteries in the remote control.
Connect the air conditioner to the power supply through a socket of the required rating, with grounding.
Make sure there are no obstacles to air movement around the indoor and outdoor units.

Selection of operating modes
The Daikin FTX20JV / RX20JV air conditioner model supports the following operating modes:
... auto selection;
... heating;
... cooling;
... drainage;
... ventilation.
In auto select mode, the air conditioner maintains the temperature within the limits you specified. If it gets colder, heating turns on, if it gets warmer, cooling.
Heating mode is suitable during cooler seasons. Keep in mind that freezing of the outdoor unit is possible in this mode, so the operation will periodically pause (no more than 10 minutes) to defrost the outdoor unit. In addition, the fan may not start immediately after pressing a button on the remote control. This is how the protection against blowing cold air works - first the heat exchanger heats up, and only then the fan turns on.
In cooling mode, the air conditioner cools the air and dehumidifies. The temperature is maintained at the level you specified.
In dehumidification mode, the electronics work in such a way as to remove moisture from the air while minimally affecting the room temperature.
In ventilation mode, air circulation throughout the room is maintained.

Additional modes and settings
For more efficient cooling and heating of the room, you can use the TURBO fan operation.
For work at night, the Sleep mode is provided. The air conditioner is quieter in it.
To save energy, the Econocool mode is provided. In this mode, the air conditioner consumes less energy.
Automatic restart. If the air conditioner worked in any mode and there was a power outage, then after the appearance of energy in the network, the operation will automatically continue in the same mode.
Timer - to start and stop the operation of the air conditioner on a schedule, it is possible to configure the start and stop at a specific time.

Useful Tips
Do not overcool the room. This leads to waste of energy and can harm your health.
Close blinds and curtains in the room to prevent sunlight from heating objects.
A large number of people and working heating devices can also complicate the operation of the air conditioner.
It is necessary to monitor the position of the vertical damper. It should be vertical when heated, and horizontal when cooled.
Keep the air filter clean. A dirty filter will interfere with the operation of the air conditioner.
Keep windows and doors closed during cooling. Do not forget to periodically ventilate the room - the air conditioner cools, but does not renew the air.
At the beginning of work, in order to cool the room faster, it is recommended to turn on the TURBO fan operation mode.
Cleaning your air conditioner
Do not touch metal parts with bare hands. Unplug the air conditioner with dry and clean hands before cleaning.
Use only detergents previously dissolved in water.
Do not use abrasive detergents, gasoline, thinners, hot water. All of these can damage the appearance of the plastic.

If you think there is a problem
The air conditioner does not work. Check if the plug is connected to the outlet. Is there power on the network. Has the shutdown timer turned off the air conditioner?
Cannot turn on the air conditioner for 3 minutes after turning it off. This is protection against frequent launches. Wait 3 minutes and try again.
During drying, the indoor fan turns off. During operation in this mode, the electronics ensures that the minimum cooling of the air occurs when the room is dehumidified. Also, it is necessary to drain condensate from the core.
During heating operation, the indoor unit stops (maximum 10 minutes). This is necessary to defrost the outdoor unit, which is covered with ice in this mode.
When heating mode is started, the indoor unit does not start working immediately. First, the heat exchanger warms up, and then the fan turns on - this protects you from being blown over by cold air.
After the appearance of power in the mains, the air conditioner began to work, although no one controlled it from the remote control. If the air conditioner was operating in any mode before the emergency power cut, then after the power supply appears, it will automatically resume operation in the same mode.
Water flows from the outdoor unit. During cooling and heating, the air conditioner contains elements colder than the environment. Condensation may form on them. If ice appears on the outdoor unit while heating the room, water will appear during defrosting.
White smoke is coming out of the outdoor unit. During heating, the air conditioner removes cold air outside, around which fog can form.
The image on the remote control has become worse, disappeared, the remote control does not work. Check the presence and correct installation of batteries. Replace them if necessary.
The room cannot be heated / cooled properly. This can be due to a number of reasons. Check if the operating mode is selected correctly, the power of the fan. Are the windows and doors in the room closed, are there any heating devices working? If there are a lot of people in the room, the cooling work will be slower. Is there dirt on the air filters?
The air coming out of the air conditioner has a strange smell. Are the air filters clean? Is there any contamination inside the air cavity? The smell may be drawn in from the outside, such as from a carpet or wall. This is especially possible when condensation gets on them and mold growth.
A crackling sound is heard when the air conditioner is operating. Fluctuations in temperature cause the plastic to resize and crackle.
A splash, gurgling is heard. This is possible with the movement of refrigerant, condensate. If the air conditioner is turned off, and there are sounds, then it is possible that this is due to the operation of the exhaust ventilation - air will flow into the room through the condensate drain hose.

When the air conditioner will not be used for a long time
If you plan on not using the conditioner for a while, it is recommended to prepare it for this.
Turn it on in heating mode. This will dry out the indoor unit and stop the growth of fungi and bacteria.
Disconnect the plug from the outlet.
Remove the batteries from the remote control.
For use after a long period of non-use it is necessary:
... make sure that there are no obstacles to air movement around both blocks;
... install batteries in the remote control;
... connect the plug to an outlet of the appropriate rating;
... check for grounding;

Installation site and electrical work
Installation work should be carried out by specialists with experience in this work.
Do not install the device in places where there is a lot of engine oil, salty humid climate, hydrogen sulfide or flammable gases in the atmosphere.
Do not place the air conditioner near high frequency equipment.
Do not place the device where the air outlet will be blocked.

Precautionary measures
Do not connect the device to a carrier, extension cord, or an outlet with an inadequate capacity.
It is forbidden to modify, change, repair the power cable and air conditioner units.
Do not place heavy, hard, hot objects on the power cord, do not place foreign objects on the indoor and outdoor units.
Do not pull out the plug from the outlet while the air conditioner is running. Disconnect it with the remote first.
Do not expose people, animals and plants to long-term exposure to the flow of cold air - this can harm your health.
Do not insert fingers, pencils or other objects into the technological openings of the air conditioner cabinet. This is fraught with injury.
If during the operation of the air conditioner an abnormality is detected, such as unusual noise, smell of burning, stop its operation, disconnect the plug from the outlet and call for technical assistance.
If the air conditioner stops heating and cooling, then you need to make sure that there is no refrigerant leakage. Call specialists.
Do not spray flammable substances on the indoor and outdoor units, as this may cause a fire.
Do not place electrical appliances and furniture under the indoor unit - condensation may form, which will damage the property.
Always clean the appliance with the plug unplugged.
Ventilate the room regularly as the air conditioner does not renew the air, but only cools / heats it.
Unplug the air conditioner during thunderstorms.
Ground the device properly.