What is digital crown. What is the Digital Crown in Apple Watch? Apple Watch button replacement as a process of replacing one of the main mechanisms

During daily use Apple Watch dirt, dust, etc. may enter the opening between the Digital Crown and the body of the device. Because of this, the wheel of the smart watch can jam or just spin tightly.

Since both generations have varying degrees of water resistance, Apple recommends spinning the wheel under a gentle stream of warm water for 10-15 seconds. This way you can wash out all the dirt from there.

How to clean Apple Watch and Apple Watch Series 2

Step 1... Turn off Apple Watch and disconnect it from the charger.

Step 2... Remove strap if made of leather.

Step 3... Run Apple Watch gently with warm, fresh water from a tap for 10-15 seconds. Do not use soap or other detergents.

Step 4... Rotate and press the digital crown while the water flows between it and the watch case.

Step 5... Dry Apple Watch with a non-abrasive, lint-free cloth.

Rate:

(No votes)

The Digital Crown in Apple Watch is such a basic control tool visually reminiscent of a crown mechanical watch, and technically performing a colossal number of functions in the downloadable from the App Store apps and directly when interacting with the WatchOS operating system.

Call Siri

Branded voice assistant Apple helps with finding the right route, sends messages, reads recent news in instant messengers, and even searches for music at the first request. There are two options to call Siri - using the phrase "Hey Siri" or by long pressing the Digital Crown. If you have problems with calling the assistant, then you should look into the settings in the Apple Watch app on the iPhone and in the "Siri" section, select the appropriate response modes.

Swimming mode

Even the first version " smart watch"Is protected from dust and moisture and calmly survives" dishwashing "or" dirty work "in the backyard. But starting with the second and third series, Apple Watch learned to switch to the "Swimming" mode, and then - to return back to operation, by removing excess moisture trapped in the case.

A similar procedure works as follows - scroll the wheel to move the watch to the active position (the dial and some system information will appear), then swipe across the display to display the control point, and then select "Water blocking". The last step is to put the watch on its side and turn the Digital Crown again to remove moisture from the speaker. The result is visible in 10 seconds!

Changing the dial

Customizing the "appearance" of the interface for WatchOS is associated with the choice of the dial: available options there are plenty - and sci-fi menus with colorful notifications, and unpretentious "cartoons" and stylish classic add-ons designed for serious businessmen and professionals.

Regardless of the choice, access to the dials is opened only when using the Digital Crown: press once, then move your finger to the screen and hold it on an available dial, and then scroll through the menu to the right or left to find a suitable setting. Optionally, you can choose and Extra options- set new activity indicators, add events or the current date.

Take a screenshot from the screen

A similar feature is available on the iPhone and iPad and on iPod Touch and, as in the case of a watch, it works by pressing two buttons at the same time. On smartphones, tablets and players, you need to press the lock button and the volume rocker. On Apple Watch - Digital Crown and a button located just below. To find out if the procedure ended as it should, a dim flash will help. The result will be added to the "Gallery", and from there - to iCloud, if installed correct settings sync and pair with iPhone.

Navigation

If, when working with two applications, it became necessary to quickly switch between them, then the Digital Crown must be pressed twice (quickly, without delay). Eventually, operating system WatchOS will allow, for example, to view recent physical activity, and at the same time - to study the data available in the browser or GPS-navigator.

If you don't need to switch, but wanted to return to main screen, then clicking on the Digital Crown costs once.

Universal access

The developers dedicated a whole section of the interface to the Voice Over function, which speaks information and events on the screen of a mobile watch with voice commands. The function is vital for people with low vision and, thus, Cupertinians diligently help to enjoy a full life even for those who are not able to see the interface.

To activate Voice Over, you need to click on the Digital Crown three times (if activation has not occurred, you will have to look into the settings of the Apple Watch application on the iPhone and in the tab "My Watch" - "Accessibility", move the slider to the active position, and at the same time set the volume parameters and the playback speed of voice prompts).

When the Voice Over function is active, each action from Apple Watch will not be displayed on the screen and within the interface, but will be spoken by voice commands (which menu is selected, current location on the map, recent events and upcoming events, dates, addressed text messages, training status, etc. recent calls). And yet - during Voice Over, as on the iPhone, iPad or iPod Touch, the way of interacting with the interface changes - the usual "one-time" clicks will become double: first for voice playback, and then - to confirm the transition.

To cancel the Voice Over action, simply tap the screen with two fingers.

You can control it in different ways - both with gestures and mechanical buttons. While everything is generally clear with the former, the capabilities of the latter are not known to everyone. The most valuable functions in real life are shown below.

Basic purpose Digital crown- scrolling up and down lists, photos and maps, as well as control of sliders (for example, decrease / increase sound, font, etc.). The side button brings up a list of contacts, which you can then call, dictate a message and even send your own heartbeat (if, of course, the addressee has Apple Watch).

And now - some useful life hacks.

Siri activation

There are two ways to call the Apple Voice Assistant - say "Hey Siri" or press and hold Digital crown until the screen displays "What can I help you with?" ("How can I help you?"). You will also feel a touch on your wrist, so the Watch will let you know that it is listening to you.

Enable Apple Pay

Press the side button twice next to a compatible terminal. The screen will display information about your credit card... Bring your watch to the terminal to pay for a product or service.

Return to Home Screen

Digital crown on  Watch- it's like a physical button. It doesn't matter which application you are in - one click on the digital analogue of the crown, and you will immediately be taken to the home screen of the watch.

Go to watch faces

After returning to the Home screen with Digital crown you can press the button again (only once, not twice). There will be a transition to the central application - and this, as you know, is the program for working with the clock. To change from one Watch Face to another, rotate Digital crown... Then press the button again.

Return to the last used application

Fast switching between programs (for example, between calendar and mail) is possible by double-clicking on Digital crown.

Opening the application

From the home screen, rotate Digital crown in order to open the desired program... This will help prevent accidentally tapping an unnecessary icon with your finger - they are all very small, so it's easy to miss.

Screenshot

The principle is the same as on the iPhone - "screen" is done by pressing two buttons at the same time. On Apple Watch this, as you might guess, Digital crown and a side button. If you can't take a screenshot, try first pressing and holding the side button and then pressing and releasing DK. If the screenshot is taken successfully, the Watch screen will illuminate with a white flash, a specific sound will be heard; you will also feel a light touch on your wrist.

Activating VoiceOver

Apple Watch can be used by people with low vision - and everyone who wants to hear what is happening on the screen right now. Activating VoiceOver mode is performed by triple clicking on Digital crown... You will hear a ringtone and Siri will tell you that VoiceOver is on. Then you can tap anywhere on the Watch screen - the announcer will read out everything that is there. After activating this mode, some functions will have to be called with other gestures, but a person already familiar with VoiceOver on iPhone will not feel any discomfort - everything will be familiar.

Turning Apple Watch on and off

If for any reason you need to restart your watch, press and hold the side button until a dedicated power saving dialog box appears on the screen. Swipe right on the desired option(to turn off, select the first one). To turn on Apple Watch press and hold the side button.

Exit a frozen application

On Watch - albeit very rarely - there are situations when this or that program "freezes". To exit it, hold down the side button and hold it until the above-mentioned energy saving dialog box appears. Then press and hold the same button again until the app closes.

As you can see Digital crown and the side button can do a lot more useful things than meets the eye. Use these features in real life to make your Apple smartwatch even more enjoyable.

The Apple Watch, starting with the second version, has, as you know, a very interesting "feature" called the "Water Lock" mode. I mean, Apple Watch Series 2 and later models can really be immersed in water without much fear.

So that in the water and under water, accidental pressing of the buttons and the dial does not cause any damage to the smart watch, in the " Water blocking»They completely disable all external physical control buttons, as well as the touch panel display.

Everything is extremely simple. However, there are a couple of interesting points too. But first, let's clarify ..

How to enable Water Lock on Apple Watch Series 2 and newer:

• go to the main watch face and swipe from the bottom to open “ «;
• in it we find and tap the button " Water blocking »(There is a droplet-shaped icon on it);
• that's it, the mode is on (a "drop" will appear on the screen).

Disabled "Water Blocking" by simply turning it counterclockwise. If you turned the crown and the clock began to beep sound signal(squeaked several times in a row), which means that the mode is disabled. And using the sound of the Apple Watch, water that has fallen under the protective grill of the speaker is removed (if at this moment you look at the watch case from below, you can see how fine water dust flies out of the speaker).

In the " Water blocking »Apple Watch functions as and without it: the screen turns on, notifications come and are displayed, etc., but only if the watch is not under water all the time.

In a completely submerged position, the built-in communication modules (Wi-Fi, Bluetooth and radio communication) receive a signal worse, therefore the exchange of data with the iPhone and / or may stop for a while. And for example, in the shower or outdoors in the rain due to water, Apple Watch should not have communication problems. Those. They show both the time and the notification normally.

But just do not forget that the buttons and the touch surface of the screen are turned off at the same time, and if you need to press something, you will have to first turn off " Water blocking"Will have to be disabled.

Apple Watch is for this device that can do more than show the time or show iPhone notifications on your wrist. The watch can be used to pay for goods in the real world, save you in an emergency, act as a fashion accessory, and help you find your lost iPhone - and that's not all.

Here are 11 tips and tricks everyone should know Apple owner Watch.

1. Check the time discreetly.

Apple users Watch Series 2 can check the time without making a noise during the meeting by slowly rotating the digital crown. You will need to "Wake Screen on Crown Up" in the Apple Watch app on iPhone under General> Wake Screen.

2. Setting up the dials.

The easiest way to customize your watch face is through the Apple Watch app on your iPhone. Apple also offers a section of watch faces based on the apps you have installed.

Instead of searching and selecting on the small screen of the watch, use the app on your smartphone.

3. Disable screenshots.

Pressing the digital crown and side buttons at the same time will take a screenshot on your Apple Watch. Before Apple provided the option to disable screenshots, my film stock was full of screenshots from accidental button presses.

Open the Apple Watch app on your iPhone, select General> Turn Turn Screenshots Off.

4. Apple Pay.

To use Apple Pay on the clock, add bank card to the Apple Watch app on your iPhone. When you're ready to pay for something, double-click the side button to activate Apple Pay. Swipe left or right on the screen to select another card, and then, bring the watch close to the payment terminal.

Another benefit of having Apple Pay on your watch is that you can use it to approve a purchase on your Mac. Setting up, enabling and customizing how Apple Pay will function on the watch takes place in the Apple Watch app on iPhone under the heading "Wallet and Apple Pay".

5. Pingg iPhone.

Is your iPhone lost somewhere? Swipe up on the Apple Watch screen to display the Control Center and tap the iPhone ping icon. Sound will play on the iPhone even if it is in silent mode. Keep pressing to keep the sound playing.

Additional help in finding a lost iPhone if it gets lost in the dark or as a sign of presence for the hearing impaired is a long press on the same icon. The sound will play and the iPhone will flash quickly.

6. Blow out the speakers from the water.

Apple Watch Series 2 owners can go for a swim without taking off their watch, but you need to clear the water from the speaker after each dive.

Swipe up on the watch face to open the Control Center and tap the water drop icon. This will put the watch into water mode by locking the screen.

Turn the Digital Crown to unlock the watch and drain water from the speaker.

7. Fast switching of applications.

The process of switching between applications on the watch can require a lot of taps and swipes. So the next time you need to switch between multiple apps, or just return to the watch face, double-tap the Digital Crown.

8. Two ways to use Siri.

You can activate Siri by pressing and holding the digital crown, or say "Hey Siri" when the screen is on.

9. Application dock.

With the release of WatchOS 3, Apple has removed the quick view of apps, adding an App Dock instead.

Press the side button on Apple Watch to see the Dock. You can move apps around in the Dock, or drag any app to the top of the watch screen to remove it from the Dock.

Another option for editing Doc is to open the Apple Watch app on your iPhone and click on "Dock> Edit".

10. SOS for peace of mind.

With the release of WatchOS 3 in September, Apple has added SOS mode to Apple watch Watch. When turned on, holding down the side button on the watch will cause the watch to dial the local emergency number. (112).

You can turn this feature on or off in the Apple Watch app on your iPhone under General> Emergency call SOS ".

11. Unlocking the Mac.

Your Apple Watch has a super feature that can unlock your Mac as soon as you wake it up.

On a Mac, open " System settings> Security & Privacy. ”Check the box to let Apple Watch unlock your Mac and enter your password when prompted.