entranceIPhone 5 in collapsible. Full disassembly iPhone
Any technique, unfortunately, not eternal. With all devices, sooner or later, problems are beginning either they are out of order. No exception and superpopular smartphones from Apple. Despite the high level of iPhone quality, they also have malfunctions. Of course, in most cases, users themselves are to blame. Perhaps each at least once dropped the phone to the floor, and some device still had to visit the water. Whatever the problem with your iPhone, it can be corrected. If you do not want to contact service centers or other offices providing phone repair services, you can do it yourself at home. All you need is to have the necessary inventory and some skill. In this article, we'll figure it out how to independently disassemble the iPhone. Let's proceed. Go!
If you disassemble your iPhone, you do it exclusively at your own risk
First of all, you need to decide on all required tools. A special set with all tools can be ordered without problems in the online store. In it, at a minimum should be:
- pentalob pumping for five petals;
- cross-shaped screwdriver;
- plastic blade with which certain parts are approaching (you can use something like that);
- vacuum sucker (or a simple suction cup, as on small toys or key chains in the car).
In principle, this will be enough to disassemble an iPhone without unnecessary problems.
Now let's turn directly to the disassembly procedure itself.
- You need to start from the bottom panel. Unscrew the screws located near the Lighting Connector using a five-point scolding. It is relevant for iphone5 / 5s and newer. If you have an iPhone 4 / 4S, then use the usual cruciform scum.
- Having understood with the screws, use the sucker to raise the screen. This is done from below, next to the "Home" button. If it fails to do easily, help yourself with a plastic blade. Please note that it is extremely recommended to apply scolding for these purposes, since it can damage the case. Use items of softer materials. Plastic is suitable.
- Raise the screen should be careful because in the iPhone 5S, unlike older models, the display is connected by a loop with motherboard. So, if you have 5s, you should not hurry. Use the plastic blade and gently turn off the loop. After that, you can safely raise the top panel.
- Having lifted the top panel with the display so that it is located at a right angle, unscrew the two screws using a cruciform reassure. Carefully find the shovel and remove the entire top panel completely.
- Now that your iPhone is divided into two halves, unscrew the screws that hold the "Home" button and get it.
- At the top of the device, everything is slightly different in models 5 and 5s. In the iPhone 5 on the mount there is a speaker fixed by two screws and spring contacts. If necessary, get the frontal chamber, which is attached by the loop. In iPhone 5S, remove the speaker, the approximation sensor and the camera can only be removed from how you remove the special mounting plate.
- The next step is to remove the metal protection fixed by screws.
- Now you can do the smartphone housing. In order not to get a blow to the current, remove the battery. Using the blade, disconnect the loop to which the battery is connected to the motherboard. Next, the battery itself and pull the label. Please note that it can be glued, so do not be afraid to make a little strength.
- At the next stage you need to get the main chamber. In the 5th model, it is reliably fixed with screws, and in 5S it is in loose state.
- After that, get the motherboard. First, disconnect the antenna connector module from the board. Then unscrew the screws holding the fee, as well as contacts near the inner wall. Now carefully remove the motherboard.
- Remove the special film from the processor. And then the processor itself.
- At the bottom of the housing are the connector under the headphones, Wi-Fi-antenna (in 5th iPhone) and the microphone. All these elements are attached to the Lighting Connector. Remove glue gloves. Please note that these items are not subject to replacement, you can only change them all together, even if some of them came out.
- At the top you will find the vibromotor, as well as GPS and Wi-Fi antennas.
- Ready. You completely disassembled your iPhone.
Disassembling iPhone 4S and more new models occurs in a similar way, with insignificant above differences.
Keep in mind that all actions of this kind you spend on your own risk. After self-operating device, the warranty will be canceled. Therefore, you should not try to independently repair your smartphone if you are not sure about your abilities.
Now you know how to disassemble the iPhone at home. Write in the comments. Whether this article helped you understand and share with other users with your experience of Disassembling / Assembling Apple Smartphones, if any.
The owners of the iPhone 5 and 5S are wondering how to disassemble the phone. Time does not gear even the most best devices: A panel can be treated (especially on black models), the sensor fails, the lovers of "swim" have problems with the hardware. To replace the parts of the iPhone you need to know internal organization And be able to disassemble the device.
What do we need?
Before starting disassembly, select a sufficient amount of time to this and stock all the necessary tools. Such a set for disassembling iPhone can be bought in any specialized online store:
- pentalob five-pilfer pumping (without her bolts, you can hardly succumb to you);
- cross-shaped screwdriver;
- vacuum sucker;
- plastic blade for disassembling the case (or something similar).
Step-by-step instruction
1. The first thing we need to do is unscrew the two screws at the bottom of the housing, on the sides of the lightning connector. In iPhone 4, cross screws were used, in later versions of Apple to prevent self-disassembly of phones, developers began to use special five-point Pentalob bolts.
If you do not have a special dump for them, you can try to use a five-pointed star or take a flat and apply it to the side of the sides. But be careful when using non-standard tools you can run the heads of the bolts. Just in case it is better to stock up the bolts of the same size, but with a cross-shaped hat.
2. With a vacuum suction cup, slightly raise the screen, helping the plastic blade. Why is a shovel, not scolding? Thus, we reduce the likelihood of damage to the case or an iPhone screen. This can be done without the help of a suction cup, picing into something (some use needle) the upper panel, but at the same time you need to observe extreme caution.
3. Gently raise the screen from the "Home" button. At this step, the first difference between models 5 and 5s appear. The iPhone 5 front panel is simply raised before the formation of almost direct angle with the case.
On the iPhone 5S the situation is more difficult. The screen is attached to the motherboard with the loop, so it is not necessary to raise it sharply. It is necessary to turn off the loop before further work with a plastic blade. And then raise the screen as in the 5 version.
4. To finally disconnect the screen, the cross-shaped hole is getting rid of the two screws on which it holds.
After neatly adhering the blade.
the iPhone was divided into two parts, each of which can be disassembled another of several components.
5. We will pay attention to the display panel. We unscrew the "Home" button. In both models it is the same.
6. At the top of the front panel, the 5 and 5S models again appeared differences. 5S has a camera, an approximation sensor and speaker, which are removed after removing the fastener plate.
In 5. iphone version The mount has a hearing speaker that keeps on two screws and spring contacts. The front camera can simply be removed if necessary, it holds on the loop.
7. The last action with the front panel is to get rid of metallic protection.
8. Let us turn to the device case. First of all, you need to get rid of the battery so as not to get a shock. Disconnect the plume from the board with a plastic blade.
By the same tool, we seem to the battery and dragging the label (in 5s it is missing, so we use only the blade). If the battery is not amenable to the first time, it is not necessary to scare, it is glued. The glue is not too strong, so the battery will easily succumb to with a little big effort.
9. Disconnect the main chamber in the 5 version. It holds on two screws, after their extraction, the camera is free. In 5s it is in such a state initially.
10. Remove the next step motherboard. There is no difference between iPhone 5 and 5S. Disconnect the antenna connector module from the motherboard. We unscrew the mounting screws to the housing and contacts in the inner wall. Gently take out the motherboard.
11. On the motherboard there is a processor: A6 in 5 and a7 in 5s. With the first disassembly, it will be necessary to remove the protective film.
12. We will continue to disassemble the case. In its lower part there is a headphone connector, a conversational speaker, Wi-Fi antenna (in version 5) and a lower microphone - all this is attached to the Lightning connector. We get rid of the mass of glue by plastic blade.
The remaining parts on the top of the case
14. As a result, we get a disassembled phone. Collect your device back can be followed by the same instructions in the reverse order.
5S version looks like:
Possible mistakes
- You yourself are fully responsible for the collection and analysis of the device. If you doubt that you will succeed, take to the service center - the wizards will help.
- With self-disassembly, remember the warranty period. After you independently open the case, the warranty is automatically lost, the subsequent repair will occur at your account.
- Do not comprehend funds for special tools: they will cost cheaper than repairs or buying a new phone.
- Do not make any sharp movements, you can tear the loop with your inaccurate actions or break the particularly fragile parts of the iPhone.
Video: Hearing iPhone 5
Video: How to disassemble iPhone 5S
For creating iPhone 5 and 5S Apple worked out so that they could not be easy to disassemble. This process will take a long time, but it is under the usual man. If you are confident - you can try to disassemble the iPhone at home yourself, in the opposite case - take the device to a literate master, he knows exactly what to do.
Users iPhone 5S After several years of active operation of the device sometimes try to disassemble it. At the same time, it is not enough to find out how to remove the cover from iPhone, you need to be able to navigate in the "filling" of the device. How to disassemble the iPhone 5S - one of the most popular versions of mobile gadgets from EPLL - see in step by step instructions below.
If you think about how to disassemble iPhone 5 and change the case, you need to prepare special tools. Each house will certainly have a set of miniature screwdrivers, but they will not fit. Replacing the housing on iPhone 5, 6 and other versions of epple gadgets requires the use of special tools that can be easily found in online stores. They are also called - sets for disassembling iPhones.
Replacing the housing on the iPhone 5S will require the use of the following 4 tools:
- Pentalob - five-point screwdriver.
- Cross screwdriver.
- Vacuum sucker (without suction cups of the case, the housing on the iPhone 5c is unlikely to be possible).
- Plastic blade (or something similar).
How to disassemble iPhone 5 and how to open the lid iPhone
In iPhone 5, the casing replacement is possible not only in conditions service Center. You can easily iPhone 5 at home, however, like other, more advanced models - 6, 7.
Model iPhone 5C Disassembly, Stages:
- The first action is unscrewing the screw at the bottom of the gadget housing. In devices 5 and above, the so-called five-point bolts are used to prevent self-disassembly by the user. Crusading screws were used in earlier models.
So, you need to unscrew the two screws at the bottom of the phone panel. If you do not have a special screwdriver, you can use a flat tool, winding it on the sides. But keep in mind that if you do not enjoy specially intended for disassembling iPhone tools, bolts can be combined. Therefore, before disassembled the device, stock up additional bolts with a cross-shaped hat.
- Take the vacuum suction cup and lift the screen, carefully helping myself with a spatula. What is the shoulder blade? In order not to damage the screen. So, for this purpose, it would be possible to use a screwdriver, in this case the chances of damaging the display would be enlarged.
- Carefully raise the screen from the Home button.
- Refer to the help of a cruciform screwdriver and disconnect two bolts on which the screen is mounted. With the help of the blade to divide the body into 2 parts.
- Unscrew the Home button. And then remove it from the device.
- At the top of the smartphone, remove the camera, speaker and the approximation sensor. But before that, it is necessary to carefully remove the mounting plate.
- Then you need to end the analysis of the front panel by removing metal protection.
- Now you can proceed to the analysis of the iphone case. And the first thing you need to remove the battery so as not to expose yourself danger of shock. To do this, you need to disconnect the loop from the board. This is done with the help of the same shovel.
Keep in mind that the battery is glued, and you need to make an effort to get it out of the phone. However, the fastening of the battery with the help of glue is not strong, and even with an easy effort, the battery will come out of the housing.
- Get the camera. Make it is pretty easy, because, unlike the previous model of the Apple smartphone, the camera is not attached to the housing.
- Extract motherboard. To do this, unscrew the screws and contacts under the rear panel. Here you can see that the board is attached quite strongly. But after unscrewing the bolts, it is easily removed from the device.
- Delete protective film processor, and get it.
- Get from the device Wi-Fi antenna, headphone jack, speaker. All parts is attached to the housing with a sufficiently large amount of glue. To remove them, you need to safely remove the adhesive mass.
- Extract the remaining parts - Wi-Fi antenna, a similar GPS device, a vibromotor for a call.
- All, procedure called iPhone 5 Disassembly, and the answer to the question how to open the back cover, completed. By remembering this simple instruction, any user will be able to understand how the casing replacement is carried out in the iPhone 5S. Collect the housing on the iPhone 5S can be followed by the same instructions in the reverse order. When the gadget is turned on, after the assembly, you will need to unlock the device by entering the password.
This looks like a fully disassembled iPhone 5S:
As you can see, disassemble the iPhone 5 with your own hands - not very difficult, sat down to everyone who is at least a bit disassembled in the technique, the task. Replacing the housing on the iPhone 5, when it is necessary after damaging it, which often happens after 2-3 years of use, can also be performed by the gadget independently. But if you fear to damage some parts of the iPhone case or its internal elements, it is better not to risk shooting rear panel And open the "stuffing". Let replacement iPhone housing 5, 6 or another version of the gadget will be produced by a specialist of the service center.
Case replacement to iPhone 5: Errors
If the replacement of the housing on the iPhone 5 and later models is 6, 7, etc. is carried out not by the master, but by the user itself, there may be different types of errors that can disturb the performance of the gadget. To avoid them, you need to familiarize yourself with the basic rules before disassembly.
In a situation where the body will be replaced in the iPhone 5C, the device owner itself should be considered as follows:
1 If the owner firmly decided to change any detail of his gadget, he must be sure that it has the necessary knowledge and skills, as well as carefully examine the instructions for disassembling an iPhone. This rule is obligatory for execution regardless of which version of the gadget will be able to understand - the fifth iPhone, 6, 6S or others - older or new versions. With the slightest doubt it is better to use the services of a professional master. 2 All work is required to be taken carefully and slowly. The details inside the iPhone are very fragile, and any careless movement can lead to their breakdown.
Literally a few hours ago at the presentation at Yerba Buena Center for the the arts in San Francisco, California, Apple introduced new generation iPhoneFounding (finally!) Serial Number 5. At first glance it may seem that we have an old familiar iPhone 4S, only a little stretched vertical. However, with detailed consideration, Apple engineers are becoming visible, in fact, created a completely new device in the usual users of the shell. Let's see what exactly changed in the new iPhone.
Design
In addition to obvious lengthening due to a new four-thyed display (about it is slightly lower), the new iPhone boasts those characteristics that will be understood only after direct contact: with all technological innovations, it has become 18% thinner, it is 20% lighter and decreased in the amount of by 12%. Also, the Johnny Ayva team was spread with unloved many glass on the rear panel. It was replaced with an aluminum insert, which certainly will not disarm when falling. All this beauty is performed on specially developed technologies - so, a 20 megapixel camera takes pictures of the iPhone case when assembling and picks up from 725 glass inserts to the rear panel of the one that will suit the best. Journalists who have managed to look at the new iPhone live, have already managed to compare the impressions of its quality with jewelry.
Display
It makes no sense to increase the display solely for its increase - adhering to such a philosophy, Apple introduced a 4-inch display, which increased by vertical. So you can still manage the phone with one big finger, but you will see much more information, be it calendar, mail or Safari in the new full screen mode. The old applications will be launched with black stripes on the sides, until the developers are updated. Improved and the display itself. It became more saturated and clear. This is not recently achieved due to the removal of the upper sensor layer - the display pixels now serve and react to touch with electrodes.
LTE
As experts propheted, the iPhone 5 received support for the LTE communication standard, with which it will be possible to forget about the speed difference between Wi-Fi and cellular connection. Of course, horse rates will depend on each specific operator. In addition, HSPA + and DC-HSDPA are built into the new iPhone - the fastest systems for mobile communications 3G. So wherever in the world you are, you can count on a quick mobile connection.
Processor A6.
Together with the iPhone got a new digit in the title and developed specifically for it processor. The A6 chip has twice the fastest of its predecessor, both in terms of processor power and in the field of graphics processing. Moreover, the design of chips specially under iOS 6 has another advantage - they have increased energy efficiency and can now hold up to 8 hours of conversations or surfing on the LTE connection, and the video can be watched full 10 hours without stopping.
ISIGHT camera
One of key functions The previous iPhone was a new camera designed to withdraw it from a category of fairly popular cameras (first place on Flickr - no joke) In the full replacement of the consumer camera. The iPhone 5 continues this tradition by updates on all fronts: Before the 720p permission, the front camera Facetime was increased, and the rear received many software bonuses, including shooting 40% faster, the creation mode for 29 megapixels, improved video stabilization and shooting at low light.
Earpods headphones
Very often it was possible to hear the reproaches that standard Apple headphones are not from the highest quality. Looks like they heard these reproaches and Apple. Together with all the devices announced on the eve of the device, there will be absolutely new Earpods headphones. According to Johnny Ayva, they were designed to take into account the anatomy of the human ear and will be perfectly sitting on everyone and everyone, not letting and not falling out. In addition, Apple Acoustics Engineers included in the Earpods structure a special diaphragm of the dynamics made from both harsh and moving materials. The result is a sound comparable to a hundred dollars a hundred more expensive.
Connector Lightning
Another component that has been completed full processing has become the usual dock connector. A new, completely digital eight-contact, entitled by Lightning (siren zipper) came to replace the 30-pin connector in the iPhone. Accordingly, the cable has become more easy, durable and - Idiot's dream! - Now you can insert it into the iPhone with any side up, without fearing something to break or damage. Well, for compatibility of a new cable with old docks (or with old iPhone) Apple will sell special adapters.
iOS 6.
Together with release new iPhone. The next way to the next version of iOS.. Among the key functions of iOS 6 - new Apple cards with 3D mode Flyover, Siri, learned to show the results of sports matches and movie schedules, Facebook integration, general "photo thumbnails", Passbook application for managing digital coupons and tickets and still hard features.
The IPhone 5 Pre-orders can be arranged from September 14, the sales of the phone will begin on September 21. Just until the end of the year, the iPhone will be available in 100 countries. When the phone sales start in Russia is still unknown.
If modern schools were so modernized and fashionable that the arithmetic would not be taught by standard textbooks, but according to the inventions of Apple, for example, according to the iPhone released, schoolchildren would know exactly the triple, then the letter G, after again Troika and G, then again This is the letter, but already S. it would be lined up in a number of four, another four, then four s, five, five with a suffix s and five with an aftercell with ... Fuh .. composed system, right? It is good that the corporation from Cupertino does not yet claim to the sphere of education and is content with the achievements in the field of IT.
Why do we tell about this in the article on the topic "How to disassemble the iPhone 5S"? So that you understand that there are much more complex things than an independent dismantling of the iPhone by our instructions. With this manual, you can easily and quickly discern the iPhone 5S on the screws and loops.
For starters, our prices for iPhone 5S maintenance services
| Repair iPhone 5S. | Price, r. |
|---|---|
| Display replacement | 2900 |
| Replacing the touchscreen (screen sensor) | 2900 |
| Replacement back cover | 2490 |
| Firmware and software repair | 890 |
| Battery Replacement (Battery) | specify |
| Repair after moisture | from 800. |
| Microphone replacement | specify |
| Replacing the charging connector (lower loop) | specify |
| Jailbreak iOS 7.x.x (jailbreak) | 900 |
| Other services | call |
| Overlook iPhone 5S. | specify |
| Phone diagnostics | Is free |
| Activating iPhone requiring Zip Code, Social Security Number (SSN), etc. | specify |
| Pruning nano-sim | 150 |
The following tools will be needed for work:
- Repair screwdriver set mobile devices. Make sure that the diameter of the tools in the kit approached the screws into the smartphone;
- Little sucker;
- Small plastic mounting blade;
- iOpener. For those who are not yet informed, explain: this is a truly male accessory from Apple, originally intended for a safe opening of beer. Does your eyebrows shot up surprised up? We understand, but call for a little wait. Soon you will understand why we need this branded opener.
We proceed to dismantling the iPhone 5S.
We suggest running again technical characteristics Smartphone. What are we here? Apple A7 processor with 64-bit architecture, innovative movement coprocessor M7, 16, 32 or 64 GB own memory Depending on the configuration, the 4-inch Retina display with 326 pixels per inch, the main chamber of 8 megapixels and the frontal for FACETIME video for 1.2 megapixels, the fingerprint scanner in the number key. And all this power and productivity, closed in dark gray, silver and gold color, do you want to disassemble? Start! But we are not responsible for your actions.
Apple, as before, strives for all ways to prevent a possible analysis of the iPhone 5S. I must say that if you came unprepared without a set of screwdrivers, about which we spoke at first, you would face an irresistible obstacle in the form of firmly screwed screws. However, thanks to us you know how they can be overcome. Without afraid, unscrew all the screws that hold the housing.
Did you unscrew all the screws fixing the panel? So proceed to the most interesting! If you have accounted for you to disassemble the iPhone, then the removal mechanism of the display using the suction cup to you. However, in the case of 5s, we would advise a little help with a plastic spatula in order to avoid drops and breakdowns of the screen.
If you are careful and patient, your efforts will pay off with interest: display iPhone 5s will start separating like oil. However, slightly raising the Retina component, you will see that the wire connects the fingerprint scanner and the Lightining port from its lower part. This feature The assembly complicates the task a little, since, pulling the suction cup too sharply, we risk the lacquer to damage the cable. Obviously, it is impossible to do this, otherwise the wire will need to be replaced.
But we are not kettles, so we do everything neatly and carefully, bypassing the dangers and traps of the independent analysis of the iPhone 5S side. All the same plastic blade separating the cable from the sensory scanner.
Finally, we can completely look at the inner device of the iPhone 5S. Already at first glance, it is clear that compared to the iPhone 5 no fundamental change occurred. The most striking difference between the iPhone 5S from the predecessor - the disappeared battery removal label.
Already loved by a plastic blade, we reveal the metal latches and start todging with the battery. Why boot? Because due to the abundant adhesive layer and the absence of a battery removal label, it seems that the manufacturer wanted to accurately stop the analysis of the iPhone 5S at this stage. Surely the insidious plan was: Even if we reach the battery, then forever bump into the glue, to which he is planted, and let's give up, without seeing the Münhausen label itself (read: a label for extracting) to pull it out.
But not on those attacked! We have found a way out and pulled out the battery with the help of the iOpener itself, like real men.
If you suddenly have excess glue, then with initial analysis, you can simply remove the adhesive grooves by creating new ones when reverse assembly.
Once you pulled the battery, you can start removing screen iPhone 5S. It is worth only disconnecting the shovel of the front camera cables, the processor of images and the LCD panel, and voila - the Retina display is removed without problems! Note that no progress, regression, and at least any significant changes in the 5s display did not happen compared to the top five. The screen did not increase, did not decrease, it has all the same qualitative characteristics. No surprises.
Now we will quickly remove the fingerprint scanner from the keys. What an exciting moment ... Outwardly, the sensory reference recognizer does not represent anything special. But the technology shrinking in it is amazed. We introduce you to the course of the case: About a year ago, the company Cupertino acquired a patented technology from Authen Tec, according to which the scanner "takes pictures" your finger, but does not send it image in Apple. In addition, thanks to the shell of sapphire glass, it remains for a long time and is practically no disassembly with such researchers as we are with you.
Go to the main chamber. As you can see, the label reads: "DNL333 41WGRF 4W61W". How, really the camera is the same as in Sony? Jim Morrison assures no. Allegedly coincides only the letter designation, and the filling is completely different.
In general, you may notice that the internal design of the iPhone 5S is characterized by simplicity and conciseness. Here are much less vulnerable cables and connecting loops that are damaged by one careless movement.
We got to Wi-Fi module. Marked as Murata 339s0205 The module is absolutely the same on smartphones with different memory capacity. Sometimes, however, there are differences in several characters, which means probably different manufacturers.
With trepidation, we study the IC characteristics of the iPhone 5S:
- Qualcomm PM8018 RF Power Management IC
- TRIQUINT TQM6M6224.
- Apple 338S1216
- SkyWorks 77355.
- Avago A790720.
- Avago A7900.
- Apple 338S120L
- SK HYNIX H2JTDG8UD3MBR 128 GB (16 GB) Nand Flash
- Broadcom BCM5976 Touchscreen Controller
- TEXAS INSTRUMENTS 343S0645 TOUCHSCREEN INTERFACE
Now they are all like a palm.
We continue to study the iPhone 5S specifications. On the inside of the logical board, we read: Apple A7 APL0698 SOC, Qualcomm MDM9615M LTE Modem, Qualcomm WTR1605LLTE / HSPA + / CDMA2K / TDSCDMA / EDGE / GPS Transceiver. These long complex names indicate only the processor marking and the presence of a long-awaited processor of the movement.
It's time to deal with another feature of the 5S model, with A7. Along with the fingerprint scanner, the A7 processor is one of the main differences between the iPhone 5S from the iPhone 5C. Apple declares that the performance of the A7 processor is half higher than the A6 indicators, therefore users for which the power of the device is priority, will not be 5 or 5C, namely iPhone 5S.
Such an increase in performance is associated, firstly, with a 64-bit architecture, and secondly, with the replacement of morally obsolete components ARMV7 to the ARMV8 set. Armv8 was designed specifically under 64-bit architecture. Which is especially valuable, it increases the performance of the gadget without hitting the time autonomous work. Since the technology has just recently appeared in mass products, we can not yet tell you more, what is its internal device.
Now the front camera that we use for self-snapshots or to communicate via video applications. After all that we have already done, her extraction is quite simple taskSince nothing but the screws does not hold it. We take our screwdriver and for business!
The bottom of the iPhone 5S case has a lot in common with the iPhone 5. However, when dismantling the device, you will definitely notice that the speaker is extracting much easier. Together with it is removed for the headset, microphone, lightining-port. Also easy and painless.
We are forced to resort to such a "team" extracting a group of components at once, since they are interconnected, and not contain individual modules.
Another hardware update iPhone 5S - double flash. Inside the chamber there are white and yellow led LEDs designed to balance colors when night shot And protect users from pictures in the style of Casper.
So, it's time to sum up some results of the analysis of the iPhone 5S. First, we were convinced that, as in the remaining branded devices, the screen was removed almost first of all, which means it can be replaced quite easily.