How to program a remote from the gate. BFT products guarantees quality and reliability

Release both buttons.

Enter the brand code using the numeric keypad on the remote control. During the input of the coder, hold the device to the device.

• If the code is entered correctly, the power button blinks once and remains to burn.
• If the code is entered incorrectly, the power button will flash four times, and then goes out. In this case, repeat the described process. Make sure you enter the correct brand code and that your device supports it.

Press the power button. Each time you press the power button, the following code (from the brand code list) is sent to the device. In this case, the power button will flash. Continue press the power button until the device turns off. This means that you found the right code.

• If you have entered all brand codes from the list, the power button will flash four times, and then goes out. In this case, use the other method described in this article.

Click and release the "STOP ■" button. This will save the code in the remote control and assign it to the button corresponding to the device turned on (that is, the button you have pressed earlier). If you do not click the "STOP ■" button, the code is saved will not and you will have to start the process again.

Test the work of the console by turning on the appropriate device and controlling it with the remote control. If you cannot manage most device functions, use the other method described in this article.

Search for manual codes

Turn on the device you will manage (TV, DVD / Bluray player, stereo and so on). The device must support the use of remote control.

• The number of functions managed with a universal remote control depends on the device.

1. Hold the button on the console that matches the device turned on. For example, if you program a remote control to control the TV, clamp the "TV" button. If the buttons corresponding to the enabled device are not on the remote control, click the "AUX" button.

   • After a few moments, the power button will light up. Continue to hold down the device button on the remote control.
   • Keep the remote direction on the device.

2. Hold down the power button while continuing to hold the device button down on the remote control. Power button will go out. Continue keeping both keys for three seconds. The power button will turn back again.

   Release both buttons. The power button indicator should burn. If this is not the case, repeat the actions described.

Programming consoles for the gate.CAME, FAAC, NICE, DORHAN, PROFESIONAL, GANT.

First of all, it is necessary to register the remote in the receiver on the control board. All manufacturers of automation for gates a different algorithm for programming consoles, therefore there is no single recipe. Let's focus on the main manufacturers of automation for the gate presented in the Ukrainian market - Professional (Gant), Came, Faac, Doorhan, Nice.

First of all, a small leakage.

In CAME, FAAC, NICE systems, one remote control is written to the drive receiver, and then the required number of other key chains is copied from it. If you try to write the following remote to the receiver - the first remote and all the remotes recorded from it will stop working. In cases where you lost the old remote, it is not necessary to delete it from the memory - it myself will erase when you write a new one in the receiver. A huge advantage of such systems is convenience - there is no need to open the cover of the electric drive every time if it was necessary to write the next remote. But this system is very vulnerable - it is enough for me to hold your remote in the hands of seconds 10, to overeat the signal to your remote. And this opens the gate to almost everyone who kept your remote control (or the console of your employees). Suppose you decided to restrict access to the parking lot, put the barrier and issued a tenant 20 CAME consoles (equal to the number of parking spaces). But after a couple of weeks there is not enough space in the parking lot. Why? Because employees give each other consoles for copying and they appeared several times more than it was issued. And how to do it can be read below.

What is the way out? Install Professional (Gant, China) or Doorhan (Dorhan, Russia) system. The main difference of such systems is that the signal of each remote control is written to the receiver individually. The minus is the limit on the number of recordable consoles in the receiver (depending on the model from 25 to 128 pcs) and the need to open the drive cover or receiver every time to record the next remote control. But such a system will not allow a sidewayl to multiply clones. Recommended for enterprises and parking with a large number of users. You can't be infinitely trusting everyone without exception to users to users? The plus is the fact that the consoles of these manufacturers are also cheaper than Italian two or three times.

How to program a remote Professional

How to program the CAME console

How to program paul Faac

How to program the Doorhan remote

How to program the Nice Remote

How to program a remote Professional 100 UAH

Press the "Learn" button on the drive control unit for the gate for the 1st second, the LEARN LED will light up. Click on the button on the keychain, the LEARN LED on the control unit flashes and goes out. Your keychain is saved.

If you need to record additional consoles, repeat this operation. It should be noted that a limited number of remote controls is recorded in the receiver's memory (depending on the amount of microcircuit's memory, the number of recovered recorded can be from 25 to 128 pcs).

To remove all keychains, you must keep the "Learn" button for 8 seconds. All keychains will be worn out of memory.

How to program the CAME remote 25 euros

You must press and hold the PROG button (CH1) on the control unit. The LED indicator begins to flash (left drawing). Press the desired button on the keychain. The LED lights up with a smooth light, which indicates a successful programming of the control unit (right figure). Release both buttons. The console is recorded.

Press and hold both buttons on the remote control, which must be programmed (new remote) (1). The LED indicator will flash quickly (2). Release the buttons and click on one that you want to program (3). The indicator should light up with even light. Not more than 10 seconds to bring the master - keychain (programmed remote) from the bottom and rear to the programmable (on which the indicator is on) and to press it once working button (four). The LED indicator breaks three times (5) and will go out (6). To program other key chains, repeat operation. In this way automatic system It can be configured to work with any number of key chain transmitters with the same code.

How to program the Panel FAAC 25 euros

To write a remote control FAAC to the drive receiver, you must simultaneously press two P1 and P2 buttons on the control panel and release them when the indicator on the remote control flashes (after 1-2 seconds). Then press and hold the button on the receiver board - the indicator on the board must be filled.

While the remote indicator flashes, you must click on the button control unit, the button that must be programmed to manage the door sash before letting the receiver button, make sure that the diode burned for about 2 seconds (in confirmation that the code is saved). Now let's release the button of the console and receiver. The console is recorded.

But if you wish to record more than one console, do not try to repeat this operation, since the next remote control (new) is recorded in the receiver, and the previous one will delete. It is necessary to carry out an operation to copy the console. How to do it below.

On the main remote control (recorded in the receiver), press and hold two P1 and P2 buttons simultaneously release them when the indicator on the remote control flashes (after 1-2 seconds).

Then place the copied (new) remote control in front of the programmed as shown in the picture above. On the main remote control (while the indicator flashes) Press and hold the button from which you want to rewrite the signal. Now click on the new remote control that the button you want to program. The indicator must flash twice as a sign that the code is saved. We release the button and repeat the operation for other proteins. Thus, the automatic system can be configured to work with any number of key chain transmitters with the same code.

How to program the Doorhan remote

Before programming, it is recommended to clear the receiver's memory from the pale codes recorded earlier. To do this, after turning on the power, hold the recording button pressed 10 seconds. The LED will flash for 10 seconds, then it will go out for 2 seconds and will blink twice again to confirm that the remote codes are erased.

To write a remote control to the receiver, press and hold the remote control button on the radio receiver on 3 seconds - the LED1 indicator on the receiver will light up. After that, press the desired button on the remote control for 2-3 seconds. To configure several remotes, repeat the procedure for other remotes.

How to program the Nice Remote

Nice's consoles meet two types - on a fixed code (blue case) and dynamic code (black housing)

Programming nICE console The FLO with a constant code is made using the configuration of the two-position DIP switches, both in the remote control itself and in the radio channel. Be careful - the variations must coincide. If you need an additional console, simply unlock the old programmed FLO remote and install the switches to the same position. These are the elutions of the old sample, today are very rare.

Let us last in more detail on programming the consoles with a dynamic code.

Nice Programming with Dynamic Code

At the receiver, press the key once (delay less than 1 sec.). On the remote control to clamp the key for 3-4 seconds, after which the indicator will flash on the receiver 3 times. This means that the remote is successfully identified and recorded in the receiver. After that, the receiver will be in programming mode for another 10 seconds, during this time,
Necessible, you can record a few more remote controls. After the expiration of time (10 sec.) The receiver will remember all the remote controls and all the buttons on each remote control.

You can also program the remote control can also be remotely, with the help of the previously recorded panel. As a result, the "new" remote control button copies the command from the "old" remote button. ATTENTION! Programming a new console from the old should occur within the receiver action radius

Click the desired button of the new console for 5 sec., Then release, press (without clicking) the button on the old remote control 3 times, on the new remote, press the same button 1 time and release. The console button is written and performs the same commands as the button of the old console.

Remote controls recorded in the receiver's memory, if necessary, can be removed. To do this, it is necessary to carry out the following operations:
Press and hold the button on the receiver, you need to wait until the LED turns 1 time, goes out 1 time, and then flips 3 times, release the button on the third flash of the LED.
If all operations are carried out correctly, then after a small pause, the LED on the receiver will obey 5 times.

Today in the world market there are many manufacturers who are engaged in automation. Its necessary to be able to properly program that the necessary technologies well work well.

Now we will look at the remotes from the gate. If you perform their exact setting, then you will protect yourself from the penetration of intruders and make life much more comfortable. You can also use the keychain not only for the opening of the gate, but also for other devices. Let's look at how to program a remote from the gate.

Camel's consoles

This company occupies leading places for the production of universal remotes. They are withstanding various climatic conditions, and they are easy to program.

TOP-432NA.

Came today is considered the highest quality and reliable. She can find many good consoles. According to consumers, the highest quality model - TOP-432NA. What is it connected with? This remote control is two-channel, which allows you to work immediately with several devices, namely, it is possible to open several devices at once, for example, a gate and barrier. Its frequency is 433.92 MHz. This model is capable of working at a fairly long distance - 140 meters. How to program a remote from the Gate Came?

1. At the first stage, it is necessary to close the remote control close to the goal.
2. Next you need to press 2 buttons. Hold them while the light bulb will not flash.
3. After that, click on any button, you just need to choose which will be used for the gate. If the indicator begins to burn exactly and stop blinking, then you did everything right.
4. We take the old remote, which went with the gate, and press the button to overwrite the code. It should be remembered that everything needs to be done quickly, while the light is on on the CAME remote control.
5. When the indicator blinks on the new console several times, the overwriting will end. Now you can use it to work with the gate.

Four-channel TOP-434NA

This remote is similar to the first model. The only difference is the size and number of devices that can be programmed. The frequency remains the same. Top-434NA - remote control. How to program it?

1. As in the first case, you need to bring the remote control to the goal and click on two keys simultaneously. We are waiting until the LED will begin.
2. Click one of the buttons to start writing on it.
3. Next, press the button on a special panel to overwrite the code.
4. After the indicator will flash 3 times, you can start using this remote. The data was successfully overwritten.

Top-432ee

Recently, a new key chain from the Top - Top-432ee series has appeared. It can allow working with devices to programming various encodings, such as there and torus. To start working with this remote control:

1. You must click on the new key chain that you want to further use to work with the gate. We are waiting until blinking on the indicator appears, and let go of the button.
2. Repeat pressing on this button.
3. After action performed, you need to quickly reduce the old console to the Top-432. Press it a key that allows you to open the gate. When the LED blinks 3 times, you can start using the device for the direct purpose.

TOP-432EV.

This console is considered an improved version of the previous model. It has quite small sizes, which allows you to wear it in your pocket. Also, the TOP-432EV may contain 4096 code operations. How to program this keychain?

1. As before, we clamp the two keys until you see the light bulb flashes. Next, let go and go to the next action.
2. Select the button to move the data.
3. We are waiting a few seconds to a permanent loss of the LED.
4. We bring a new console to the bottom of another keychain and wait until the overwriting is performed. It usually takes about 10-20 seconds. When the LED blinks 3 times, you can be sure that the recording has been successfully completed.

Came Twin.

Another novelty is the key chain Came Twin. It has one feature - code protection. Sustier people will not be able to just take possession of the code to open your gate. They are also produced in different variations - Two and four buttons. Came Twin is capable of working with a dynamic code. How to program a remote from the gate?

1. First you need to make sure that this key chain can already be used and there is a button for receiving the signal.
2. Drive the remote as close as possible to the receiver.
3. Next, we take the old key chain and press the key where the required code is recorded. We are waiting until the LED is lit.
4. After 10 seconds, press the key, which is on the old panel.
5. After about 20 seconds, the code recording process will end.

NICE.

Italian company Nice is located in the production top automated systems For various equipment. Their products are quite high quality and reliable. Of course, they have universal consoles that allow you to manage some processes at the same time. How to program the remotes from the Nice gate?

Nice Flo and Flor

Keychains from NICE are quite simply programmed. All models of the FLO and FLOR line can work with a dynamic code at a frequency of 433.92 MHz. They can work, even if you are at a distance of 140 meters from the required object. The consoles are released with one, two or four keys. Consider on the example how to program the remote from the Nice Flo2R gate.

1. First you should approach the receiver.
2. It is necessary to arrange the consoles consistently.
3. Next, select the key to record the code and click on it.
4. After 5 seconds, you can click on the button that is used to open the gate on the old panel.
5. It remains only to repeat the keystroke on the first palette. The button programming is completed.

Hormann.

This is a German firm that makes a bet on quality. Her products are quite reliable and beautiful. The manufacturer stains various buttons in different colors to determine for them certain frequencies (blue - 868 MHz, green - 26,975 MHz, gray - 40 MHz).

HORMANN HSM 4.

This model is equipped with four buttons that allow you to control various equipment. HORMANN HSM 4 has a frequency of 868 MHz and the ability to use dynamic code. You can also note the rather small size of the keyfob. How to program a remote from the gate HORMANN HSM 4?

1. We place a new panel near the old one.
2. After that, you must press a key with which reading will be performed. We are waiting until the light bulb will be lit.
3. Next, you need to click on the key that you need to use later. After 5 seconds, the LED will flash quickly. Code transmission completed.

HORMANN HSE2 and HSM

HSE2 has two-channel mode Works, and HSM - two and four-channel modes. It has a small size, which allows you to cling it to the keys. The first model operates at a frequency of 868 MHz, and the second is 40,680 MHz. To program them:

1. First you need to position the consoles close to each other.
2. We take the old key chain and click on the key with which you want to read the data.
3. Next, press the key you select to use in a new console.
4. It remains only to wait for the flashing LED. We release the keys and we can start using this console.

Doorhan.

Doorhan is a Russian company. She has long been on the world market and supplies high-quality equipment for automating work with goal and radio receivers.

Doorhan Transmitter 2, TRANSMITTER 4

These models work with a dynamic code at a frequency of 433 MHz. As you have already noticed from the name, key rings can work with 2 or 4 various devices. How to program the remote from the doorhan gate?

1. First you need to delete old records. To do this, press the key with which you can record, and wait. After 15 seconds everything will be deleted.
2. Next, click on the SW1 button (or any other you want to program) and on the old key chain for writing data. We are waiting for a few seconds.
3. This is completed on this. You can proceed to use.

Company BFT.

The most common consoles of this company are BFT Mitto 2-12, BFT Mitto 4-12. They are two and four-channel, respectively. Could work at a frequency of 433.92 MHz. How to program the remote from the BFT gate?

1. To transfer the data, press the OK key.
2. Next, go to Parameter and click a couple of times on the "-" button.
3. We repeat pressing OK. After that you will find yourself in the menu where you can add the device.
4. Click on the AD START key and click on the required button.
5. Next, we click on the appropriate key in the old key chain and wait until the data is converted.

FAAC

This is a rather popular Italian company. Its products are used in many countries of the world.

FAAC XT2-868 SLH and XT4-868 SLH

These models are used to control two or four devices. XT2-868 SLH and XT4-868 SLH operate with a frequency of 868 and 35 MHz, respectively. They can also be used in various climatic conditions. How to program a remote from the FAAC gate?

1. First you need to simultaneously press the P1 and P2 buttons to program the keychain.
2. Next you need to arrange the consoles together.
3. As soon as the LED starts to burn, you must hold the key on the old device, which will be used in the record.
4. In the new console, select the Slave button. After 15 seconds, the recording will end. Next, you can start using this console.

Conclusion

Today you can program the considered remotes for many devices. How to program a remote from the gate? As you might notice, this is done quite simple. In many consoles, actions are very similar. So that everything went to successfully, hold the instructions. Console You can choose any firm what you enjoy. Of course, you should choose the desired frequency. It will be an important parameter when choosing a remote.

Consoles for gates and barriers are the most convenient devices for automatic control of barriers. They differ in the radio signal frequency and encoding, modulation and other parameters. In order for a model of one manufacturer to open a barrier of another brand, all parameters must match. There is no single apparatus for opening a barrier. Create universal devices capable of opening the fences of those producers who are made to the database. In the previous, we talked about universal key chains for barriers, now consider them more detailed.

Advantages of universal brass

• support programming 4-30 devices;
• manage multiple mechanisms on the automation of one manufacturer;
• work on several modes;
• simple in the setup, compact;
• compatible models support multiple frequency ranges.

Principle of operation

The console for the fence of a particular brand works only on one specific frequency. A universal compatible device supports multiple frequencies at the same time. It programms several codes of various manufacturers, so such devices are suitable for managing several types of equipment. In the instructions for the product, it can be controlled by what devices and models of barriers can control. Universal panels for barriers can also be configured to control other devices, such as intercom.

Universal panels for barriers and gates

The new universal panel for the barrier must be programmed correctly. The universal product is different from compatible in that programming is possible only at one frequency, you can write only one type of encoding. Only in this case it will work adequately. To configure the operation of each button, the encoding from the original is recorded on it. The control system allows you to "remember" various programmed signals. The type of signal and frequency must necessarily coincide.

The fence receiver receives a signal from a multifunctional remote. The unique signal is checked with the base. When the data is coincided, the barrier opens and then closes in its original position. Special filters support the desired frequency without change, so that external factors do not affect the operation of the device, for example. Universal remote For barriers, it is suitable for control to 10 standard keychains.

Transfer software code From one device on a compatible universal device and making changes is possible only for the first 5 seconds after turning on the new console. Initially, the desired button is clamped on a new device before receiving the beep. Then you need to take an old device from the fence and click on it, keeping the appearance of two short sound signals And let it go. Then, to transfer the program code, click the button on the old device several times:

• one - step-by-step mode;
• two - the rise of the mechanism;
• three - lowering the bar;
• four - stop.

Manual for programming the console usually included

After pressing, sound signals should be sounded in the quantity that corresponds to the programmable management command. After about 2 seconds, you need to confirm the programmed command by clicking the button again until the first signal appears. With successful programming, three signals should be sounded.

To make a new device in the control unit, you must first at the new, then press the button on the old console, while holding 3 seconds. Then confirm the operation on a new device while holding the button 3 seconds. There will be 3 signals that promote the successful completion of the operation.

On universal devices with light indicators, for example, CAME TOP, instead of sound signals use light. Only one instance is programmed to a new console, and the parameters are adjusted. As a rule, two buttons are pressed, which must be programmed on the old apparatus before flashing.

Then press one button on it until the smooth luminescence appears and bring to a new device and click on it the operating button. The indicator should notify the successful end of the flash operation. In this way, work is configured different models To control on one multifunction machine with one code.

Types of universal brass

Take the Multi Universal Consample for the example 4. The remote control can store 4 keys data operating in the frequency range of 315-868.3 MHz. These are CAME, NICE, HORMANN, MARANTEC, DITEC, FACC, MAROG, Marantec, Ditec, Facc, Marantec, Ditec, Hormann, Marantec, Ditec, Facc.

The BRO console models are two-, three and four-channel. Work on a 12B battery, have a light indication. Used in the range of 433 MHz using a dynamic code, have a high range. Cost from 1000 rubles.

APOLLO Radi-Remote Control Details various codesCreated to replace up to 4 copies. Suitable for gates and barriers. There is a model within 750-1200 rubles.

Jolly Open models operate at 433 MHz. Sustainable mechanical shocks, equipped with a movable keyboard. Remembers up to four copies. The cost is 600-700 rubles.

Tech - two- and three-channel apparatus operating at a frequency of 433 MHz. Equipped with light indication. Compatible with Beninca models. It costs from 540 rubles.

DITEC GOL4 C and TRANSMITER - Universal devices suitable for managing any devices on the Doorhan automation. Have 4 independent channels and floating code with 16 million combinations. Cost from 750 rubles.

TX2 / 4 consoles support combination with any models on the FAAC automation. Support two modes of operation: Master and Slave. For programming multiple instruments, only Master is used. There is a model from 1200 rubles.

One-, two- and four-channel channel Intro supports programming up to 30 remote controls on the Radio series. Can manage barriers, rollers, lighting and gates. Cost from 1200 rubles.