How to program a universal remote control. Faac is a recognized market leader in the production of automatic barriers, gates

The barrier is one of the elements of the access restriction system.

The modern vision of such systems implies automatic operation the totality of these elements, including the presence remote control some devices.

Came is a manufacturer of these systems and their components. All devices are extremely easy to use, safe and affordable.

The quality of the products is guaranteed by the inspection system adopted by the company. It implies selective testing at all stages of production up to release for sale.

Radio control

Literally all Came devices that are designed for remote control of barriers, that is, multichannel transmitter key fobs, which can be called the collective word "remotes", have several general characteristics and qualities.

The company produces several series of control panels for barriers, which are able to meet the requirements of both the private sector and large industrial enterprises.

ATOMO series

Here the customer can choose both two- and four-channel versions depending on his needs. All of these devices are suitable for use in environments with increased safety requirements.

The fact is that it is implemented here a special technology called "Rolling code" is the so-called dynamic code.

Rolling code technology is able to prevent all attempts to copy or overwrite signals. This became possible due to the constant change of signals sent from the transmitter.

None of them are repeated. The security guarantee in this case is guaranteed by the fact that the number of different code combinations exceeds four billion by almost a third.

Also, these devices have implemented automatic detection codes going from transmitter to transmitter, and there is a transponder function.

Top EE Series

The most popular models that are used mainly in the residential private sector. As in Atomo, two- and four-channel versions are available to customers, which, moreover, have a transponder function.

Twin series

These keyfob transmitters are ideal for controlling multiple access restriction systems at once. Technology is implemented here secret code- "Key Code", which is able to prevent attempts to intercept the signal.

The maximum number of possible combinations, as for the Atomo series, is over 4 billion.

Model Top 432NA

This radio device is designed to operate on frequency 433.92 MHz... Equipped with protection against signal copying, thanks to the multi-code function.

1. Design... The device is housed in an elegant gray housing that fits easily in your hand. The flexible lines make it pleasant to use, and the laconic design makes it easy to use - an LED at the top and two buttons in the center.
2. Specifications.

• Meals - two lithium batteries CR2016.
• Weight - maximum 16 grams.
• Operates in the range from -20 to + 55 ° C.
• Working range - from 50 to 150 m.

1. Price... Depending on the region and the current euro rate - from 900 to 1500 rubles for the 2-channel version and up to 2000 rubles for the 4-channel version.

Model Top 432EE

This version was released by the company as a modification of the most popular Top 432NA model. The main modification and difference from previous models is work simultaneously in two coding systems - TOP andTAM... This further enhances the safety of use. Otherwise, these devices completely replace the previous models.

It is also provided here signal interception protection which is provided quite a large number code combinations - more than four thousand.

For the convenience of users, it provides function of defining the code in automatic mode , which makes possible extremely simple programming of one remote control from another.

The cost is slightly higher than the Top 432NA. You can buy it for a minimum of 1,300 rubles and a maximum of 2,500 rubles for the four-channel version.

How to program?

There is a specific programming algorithm that, in general terms, will be the same for all Came consoles. The system is built in such a way that only one remote control can be written to the drive receiver.

When there is a need for additional ones, they will be copied already from him. If an attempt is made to record another remote control into the receiver itself, then the first one and all that were recorded by copying from it will stop working.

This is convenient, for example, if the first remote control has been lost. Then you can simply purchase and program a new one, and the previous one will be erased from memory on its own and no one else can use it.

This is the additional convenience of the system - there is no need to repeat the operation every time you program a new device, holding open lid direct receiver.

However, this same feature is at the same time a hidden danger of the entire system. After all, having received a working programmed remote control for a short time, anyone can use it in order to configure their own from him in the same way.

Therefore, you should pay close attention to safety and prevent cases of falling of working devices in the hands of unauthorized persons.

Brief instruction - programming key fobs to the control unit

1. Open the cover of the control unit and find the CH1 (PROG) button.
2. When you press it, the LED indicator located on the panel will start working.
3. Further, to start programming the keyfob, you must press the corresponding button on it without releasing the PROG button.
4. After that, the indicator light stops blinking and starts to burn steadily.
5. Such a LED signal indicates that the keyfob has been successfully written into the control unit memory. Then both buttons can be released.

The console obtained as a result of such an operation will be called master keychain... Everything further actions the preparation of new devices will be carried out only with its help, without including the main control board and receiver in the process.

Copying of the TOP series consoles (432NA, 432SA) from the "master"

First of all, it is worth remembering that both devices must be sequentially positioned one after the other so that the first is the new remote control that requires adjustment, and the old one, the “master key fob”, is behind it.

The distance between them for the successful completion of the entire operation should be no more than 5 mm. You can just put them back to back. Only then does the programming process begin.

1. On a new device, press and hold both buttons until the LED turns on and starts flashing at a fairly high frequency. This should take about 7 seconds. This means that the key fob is ready to copy the signal.
2. The next step is to release both buttons on the same device (new) and press (briefly) only the one that will be programmed. After that, the LED should stop blinking and start to light up steadily.
3. All further actions should be done fairly quickly - you need to be in time for the time when the indicator on the new remote control is evenly lit.
4. On the master keyfob, press the operating control key once. It is from it that copying or rewriting of the current signal will be carried out.
5. After that, the LED should blink three times and go out completely. Such a light signal means that the signal copying operation was successful, and the new device is fully operational.

You can increase the number of working remote controls, multiply them for a large number of users. To do this, repeat the steps that are described in paragraphs 1-5 of the above instructions.

Signal dubbing to Came TOP-432EE from TOP-432NA device

As the TOP-432EE remotes become more common, you should know how to set up this unit using the previous 432NA model.

1. On the 432EE, two buttons must be pressed at the same time. You should hold them until the LED indicator lights up constantly flashing light.
2. Then both keys are released and one is pressed - the one that will be programmed.
3. After that, the indicator on the new device should stop blinking and stay on constantly, with the same intensity.
4. Within 10 seconds, while the LED is on, it is necessary to bring it to the bottom and back of the programmable remote control old model 432NA.
5. On the master key fob, you need to make a single and short press working key... After that, the indicator should blink three times, which means the completion of signal rewriting and successful programming.

Automation of barriers implies ease of use and comfort for users, which would be impossible without high-quality remote control.

Instructions for setting up the TOP 432 NA keyfob are presented in the video:

Programming remote controls for gates.Came, Faac, Nice, Dorhan, Profesional, Gant.

The first step is to register the remote control into the receiver on the control board. All manufacturers of gate automation have a different programming algorithm for remote controls, so there is no single recipe. Let's dwell on the main manufacturers of gate automation presented on the Ukrainian market - Professional (GANT), Came, FAAC, Doorhan, Nice.

First of all, a small educational program.

In Came, FAAC, Nice systems, one remote control is written to the drive receiver, and then the required number of other remote controls is copied from it. If you try to record the next remote control into the receiver, the first remote control and all remote controls recorded from it will stop working. If you have lost the old remote control, there is no need to delete it from memory - it will be erased by itself when you write a new one into the receiver. A huge advantage of such systems is convenience - there is no need to open the cover of the electric drive every time if it becomes necessary to record the next remote control. But this system is very vulnerable - I just need to hold your remote control for 10 seconds to steal a signal on my remote control. And this opens the gates to almost everyone who was holding your control panel (or the control panel of your employees). Let's say you decided to restrict access to the parking lot, put up a barrier and gave tenants 20 Came consoles (equal to the number of parking spaces). But after a couple of weeks there is not enough parking space again. Why? Because employees give each other remotes for copying and there are several times more of them than were given out. You can read how to do this below.

What is the way out? Install the system of Professional (GANT, China) or Doorhan (Dorhan, Russia). The main difference between such systems is that the signal of each console is recorded in the receiver individually. The downside is the limitation on the number of consoles recorded in the receiver (depending on the model, from 25 to 128 pieces) and the need to open the drive or receiver cover each time to record the next remote control. But such a system will not allow clones to be multiplied on the sly. Recommended for businesses and car parks with big amount users. You can't have unlimited trust in every single employee-user, can you? An advantage is the fact that the remotes of these manufacturers are also two to three times cheaper than the Italian ones.

How to program the Professional remote

How to program remote Came

How to program the FAAC remote control

How to program the Doorhan remote control

How to program the NICE remote

How to program the remote Professional 100 UAH

Press the "LEARN" button on the gate operator control unit for 1 second, the "LEARN" LED will light up. Press the button on the key fob, the "LEARN" LED on the control unit will blink and go out. Your keychain has been saved.

If you need to record additional remotes, repeat this operation. It should be noted that a limited number of consoles are recorded in the receiver's memory (depending on the memory capacity of the microcircuit, the number of recorded consoles can be from 25 to 128 pcs).

To remove all key fobs, you must hold down the "LEARN" button for 8 seconds. All keychains will be erased from memory.

How to program Came 25 Euro remote control

It is necessary to press and hold the PROG (CH1) button on the control unit. The LED indicator starts flashing (left figure). Press the required button on the key fob. The LED indicator lights up with a steady light, which indicates the successful programming of the control unit (right figure). Release both buttons. The console is recorded.

Press and hold both buttons on the remote control you want to program (new remote control) (1). The LED indicator on it will start flashing quickly (2). Release the buttons and press the one you want to program (3). The indicator should light up with a steady light. In no more than 10 seconds, bring the master keyfob (programmed remote control) from below and behind to the programmed one (on which the indicator is on) and press once operating button(4). The LED indicator will flash three times (5) and extinguish (6). To program other remote controls, repeat the operation. Thus, the automatic system can be configured to work with any number of remote control transmitters with the same code.

How to program the FAAC 25 Euro remote control

To record the FAAC remote control into the drive receiver, you must simultaneously press two buttons P1 and P2 on the control panel and release them when the indicator on the remote control blinks (after 1-2 seconds). Then press and hold the button on the receiver board - the indicator on the board should blink.

While the remote control indicator is blinking, you must press the button on the gate control panel that needs to be programmed to control the gate leaf.Before releasing the receiver button, make sure that the diode is on for about 2 seconds (to confirm that the code has been saved). Now we release the button of the remote control and the receiver. The console is recorded.

But if you want to record more than one remote control, do not try to repeat this operation, as the next remote control (new) will be written to the receiver, and the previous one will be deleted. It is necessary to carry out the operation to copy the remote control. See below how to do this.

On the main remote control (recorded in the receiver), press and hold simultaneously the two buttons P1 and P2 and release them when the indicator on the remote control blinks (after 1-2 seconds).

Then place the copied (new) remote opposite the programmed one as shown in the picture above. On the main remote control (while the indicator is blinking), press and hold the button from which you want to rewrite the signal. Now press on the new remote control the button you want to program. The indicator should flash twice to indicate that the code has been saved. Let go of the button and repeat the operation for other proteins. Thus, the automatic system can be configured to work with any number of remote control transmitters with the same code.

How to program the Doorhan remote control

Before starting programming, it is recommended to clear the receiver's memory of the previously recorded remote control codes. To do this, after turning on the power, hold the record button of the remotes pressed for 10 seconds. The LED will blink for 10 seconds, then go out for 2 seconds and blink twice again to confirm that the remote control codes stored in the memory have been erased.

To write the remote control to the receiver, press and hold for 3 seconds the button for recording the remotes on the radio receiver board - the LED1 indicator on the receiver will light up. Then press the required button on the remote control for 2-3 seconds. To set up multiple remotes, repeat the procedure for other remotes.

How to program the NICE remote

NICE remotes are of two types - fixed code (blue body) and rolling code (black body)

Remote programming Nice flo with a permanent code is made by setting the dip switches, both in the console itself and in the radio channel. Be careful - the variations must match. If you need an additional remote, simply spin up the old pre-programmed Flo remote and set the switches to the same position. These are old-style remotes, which are very rare today.

Let's take a closer look at programming remote controls with dynamic code.

Programming Nice Consoles with Rolling Code

Press the button on the receiver once (delay is less than 1 sec.). Press the button on the remote control for 3-4 seconds, after which the indicator on the receiver will blink 3 times. This means that the remote control has been successfully recognized and written to the receiver. After that, the receiver will be in the programming mode for another 10 seconds, during this time, by
if necessary, you can record several more remotes. After the expiration of the time (10 seconds), the receiver will remember all the remote controls assigned to it and all the buttons on each remote control.

You can also program the remote control remotely using a previously recorded remote control. As a result, the button of the "new" remote control will copy the command from the button of the "old" remote control. ATTENTION! Programming a new remote control from the old one must occur within the range of the receiver

Press the desired button of the new remote control for 5 seconds, then release, Press (without holding down) the button on the old remote control 3 times, On the new remote control, press the same button 1 time and release. The remote control button is recorded and performs the same commands as the old remote control button.

The remotes stored in the receiver's memory, if necessary, can be deleted. To do this, you need to carry out the following operations:
Press and hold the button on the receiver, You need to wait until the LED lights up 1 time, goes out 1 time, and then blinks 3 times, Release the button on the third LED flash.
If all operations are carried out correctly, then after a short pause, the LED on the receiver will blink 5 times.

Automatic systems for entrance gates make it possible to open the passage using the control panel so simply and comfortably that if the program fails or fails, many drivers no longer remember how to open the passage to the courtyard with their hands. In this case, you have to look for a duplicate remote control from the gate or remember how the device is programmed.

How to program the remote control correctly

A properly configured device is a rather complex device. When the gate opening button is pressed, the sequence of signals wired into the device's memory is sent over the radio channel to the receiver of the automatic gate. In this case, the following happens:

• The received signal is decrypted by an electronic chip;
• The signal from the control panel is checked against the signature recorded in the memory of the control unit;
• Confirmation of gate actuation is sent to the remote control memory.

Advice! Of course, for users all the subtleties of work automatic system there is no need to know the gate control. It is enough to know how to program the remote control for the gate in order to make a duplicate of the device in case the original is lost.

For these purposes, you can order the remote control from the company that installed the automatic gate system, but it is easier and cheaper to use a universal key fob that matches your remote control.

Universal panels for gates and barriers

The main difference between the branded remote control and the universal device is that the latter does not have a precisely fixed radio transmission frequency, as the manufacturers of automatic gates do in their key fobs. The universal keyfob can be adjusted to the format of one of the few, approximately 10-20 types, compatible with the “universal” models of remote controls. So the versatility of such a device is slightly overestimated.

It is clear that the universal control panel can be used only if it is programmed correctly. To do this, you need to rewrite control program from another remote. You can fill the program into the memory of the universal key fob immediately after turning on the device. If you have not made the transfer within 5 seconds, the reprogramming option is blocked, therefore, after switching on, you must immediately transfer the "station wagon" to the programming mode by pressing the corresponding button, after which the device will emit a signal ready to receive information.

Next, we take the old branded device and press the "mode" button until we hear two short beeps, after which we press in turn the control buttons for opening and closing the gate. Successful transfer is confirmed by a three-pulse beep.

Each key fob or remote control has its own digital name, programmed into the memory of the gate control unit, therefore, before using a new unit, it must be registered in the control unit memory. To do this, press the button on the old and on the new remote control for three seconds, then remove the branded key fob, and on the new one, press again until a threefold signal appears.

Programming of branded control devices

Each manufacturer of automatics uses approximately the same command sequences and control panel programming methods to control gates. The difference can only be in the indication of the operations performed or in the way of data exchange. Most often, remote control systems are used:

1. Permanent control key, wired into the memory block. The complexity of the key and the large length allows you not to be afraid of breaking the gate control unit with the help of foreign devices;
2. A dynamically changing encrypted key. In this case, the control unit can transmit a new digital sequence to the control panel, which is used as an access identifier.

For your information! In simple Chinese gate control systems, the first option is most often used; in expensive Italian and German automatic machines, the second control principle is used.

Gate remote control "Came"

To illustrate, you can consider the procedure for transferring service information to a new programmable key fob using the example of the TOP 432 SA model. Today it is one of the most common variants of a two-channel automatic gate control system.

The transfer of the program is performed in the following sequence:

1. To begin with, we place the old and new key fobs at the most convenient distance, but no more than 5 m. On the new device, press and hold the first couple of buttons until the indicator starts flashing rapidly;
2. Press the required button on the programmable remote control, on which you need to sew the corresponding command from the old one, the indicator will light up with a steady light. Within ten seconds, press the desired command on the old device;
3. If the transfer is successful, the new keychain will blink the indicator three times.

The procedure for programming the “Came Twin” system console with a dynamically changing code is more complicated. In this case, before transferring the program, a procedure for registering the key fob in the memory of the control unit will be required. The transfer of information is carried out through the control unit. To do this, click start button on the old block and hold it until the indicator lights up with a steady light without flickering.

To get a code for a new remote control, you need to press the button on it just once. Further, the keyfobs will exit the programming mode automatically.

Gate remote control "Faac"

The company "Faac" from Italy is known for its systems for automatic, remote controlled gates. The procedure for programming the device does not differ much from the previous options.

For example, for the XT2-868 SLH model, information transfer is performed in the following sequence. First, on the old remote control, you must simultaneously press the first two buttons, for about two seconds. The remote control switches to the information transfer mode. The new device should blink, thereby signaling the start of rewriting. Sequentially, first on the old one, then on the new one, we press the button that needs to be overwritten, after which the indicator should blink twice. All commands are transferred in the same way.

We program the gate key fob "Nice Very VE"

This model works using statistical code. Before transferring service information, you will need to open the receiver panel and code the device in accordance with the location of the switches on the board.

First, press the first two buttons at the same time until the indicator lights up without flashing. We look at the position of the first micro-toggle switch, if it is in the "on" state, then press the upper button on the remote control, otherwise - the lower one. In this way, it is necessary to "sort out" all ten micro-switches of the board. To save the information, you must turn on the last switch for ten seconds. A blinking indicator confirms the recording of information.

Conclusion

The modern element base used in control panels and gate receiving units is developing very quickly. Today, most of the service management functions are successfully performed using emulator programs on mobile phones, tablets or even game consoles. The only way to prevent possible hacking of service information is to use the most simple and low-power systems, the signal of which cannot be received further than 5-6 meters.

Panels for gates and barriers are the most convenient devices for automatic control of barriers. They differ in the frequency of the radio signal and coding, modulation and other parameters. For a model of one manufacturer to open a barrier of another brand, all parameters must match. There is no single apparatus for opening the barrier. They create universal devices that can open the fences of those manufacturers who are included in the base. In the previous one, we talked a little about universal key fobs for barriers, now we will consider them in more detail.

Benefits of universal keyfobs

• support programming of 4-30 devices;
• control several mechanisms on the automatics of one manufacturer;
• work in several modes;
• easy to set up, compact;
• compatible models support multiple frequency bands.

Principle of operation

The fencing console of a particular brand only operates on one specific frequency. The universal compatible device supports multiple frequencies at the same time. Several codes from different manufacturers are programmed into it, therefore such devices are suitable for controlling several types of equipment. The instructions for the product indicate which devices and models of barriers it can control. Universal control panels for barriers can also be configured to control other devices, for example, an on-door speakerphone.

Universal panels for barriers and gates

New Universal remote the barrier must be programmed correctly. A universal product differs from a compatible product in that programming is possible only at one frequency, only one type of encoding can be recorded. Only in this case will it work adequately. To customize the operation of each button, an encoding from the original is written to it. The control system allows you to "memorize" various programmed signals. Signal type and frequency must be the same.

The fence receiver receives the signal from the multifunctional control panel. The unique signal is checked against the base. If the data match, the barrier opens and then closes to its original position. Special filters maintain the desired frequency unchanged so that external factors, such as weather, do not affect the operation of the device. The universal control panel for barriers is suitable for controlling up to 10 standard key fobs.

Transfer program code from one device to a compatible universal device and making changes is possible only within the first 5 seconds after turning on the new remote control. Initially, the desired button is clamped on the new device until a sound signal is received. Then you need to take the old device from the fence and press the button on it, holding it until two short sound signals and let her go. Then, to transfer the program code, you need to press the button on the old device several times:

• one - step-by-step mode;
• two - lifting the mechanism;
• three - lowering the bar;
• four - stop.

Remote programming instructions are usually included in the kit

After pressing, sound signals should sound in the amount corresponding to the programmed control command. After about 2 seconds, the programmed command must be confirmed by pressing the button again until the first signal appears. If programming is successful, three beeps should sound.

To add a new device to the control unit, you must first use the new one, then press the button on the old remote control, holding it for 3 seconds. Then confirm the operation on the new device by holding the button for 3 seconds. 3 beeps will appear to indicate the successful completion of the operation.

On universal devices with light indicators, for example, Came TOP, light signals are used instead of sound signals. Only one copy is programmed into the new remote control, and the parameters are adjusted for the rest. As a rule, two buttons are pressed, which must be programmed on the old device before flashing appears.

Then they press one button on it until an even glow appears and bring it to the new apparatus and press the operating button on it. The indicator should indicate the successful completion of the operation with a flash. In this way, work is configured different models for control on one multifunctional device with one code.

Types of universal key chains

Take the Multi 4 universal remote control for example. The remote can store data from 4 keys operating in the frequency range 315-868.3 MHz. These are consoles of the brands Came, Nice, Hormann, Marantec, DITEC, FACC, etc. The price of such a remote control is around 700 rubles.

BRO models are available in 2-, 3- and 4-channel models. They run on a 12V battery and have a light indication. They are used in the 433 MHz band using dynamic code and have a long range. Cost from 1000 rubles.

The Apollo remote keyfob is designed for control panels with different codes, can replace up to 4 copies. Suitable for gates and barriers. The model costs between 750-1200 rubles.

Jolly Open models operate at 433 MHz. Resistant to mechanical shock, equipped with a movable keyboard. Remembers up to four copies. The cost is 600-700 rubles.

TECH is a two- and three-channel device operating at 433 MHz. Equipped with light indication. Compatible with Beninca models. It costs from 540 rubles.

DITEC GOL4 C and Transmitter are universal devices suitable for controlling any devices on DoorHan automation. They have 4 independent channels and a floating code with 16 million combinations. Cost from 750 rubles.

TX2 / 4 consoles are compatible with any FAAC models. They support two modes of operation: Master and Slave. Only the Master is used to program multiple fixtures. The model costs from 1200 rubles.

One-, two- and four-channel channel device Intro supports programming of up to 30 remotes on the automation of the Radio series. It can control barriers, roller shutters, lighting and gates. Cost from 1200 rubles.

Turn on the device you will be controlling. The search for brand codes is only supported by older TVs, DVD players, VCRs and satellite receivers. It is not supported by stereos, DVRs, or HDTVs (for these devices, use the other method described in this article).

• The brand code can be found in the console documentation or on this website.

Release both buttons.

Enter the brand code using the numeric keypad on the remote. While entering the code, keep the remote control pointed at the device.

• If the code is entered correctly, the power button will blink once and remain lit.
• If the code is entered incorrectly, the power button will blink four times and then turn off. In this case, repeat the described process. Make sure you enter the correct brand code and that your device supports it.

Press the power button. Each time you press the power button, the next code (from the list of brand codes) is sent to the device. The power button will blink. Continue pressing the power button until the device turns off. This means that you have found the correct code.

• If you've entered all the brand codes on the list, the power button will blink four times and then turn off. In this case, use the other method described in this article.

Press and release the "Stop ■" button. This will save the code in the remote and assign it to the button corresponding to the switched on device (that is, the button you pressed earlier). If you do not press the "Stop ■" button, the code will not be saved and you will have to start the process over.

Test the operation of the remote control by turning on the corresponding device and operating it with the remote control. If you are unable to control most of the device's functions, use the other method described in this article.

Finding Codes Manually

Turn on the device you will be controlling (TV, DVD / Bluray player, stereo, etc.). The device must support the use of a remote control.

• The number of functions controlled from the universal remote control depends on the device.

1. Press the button on the remote control corresponding to the switched on device. For example, if you are programming a remote control to control a TV, hold down the "TV" button. If there is no button corresponding to the switched on device on the remote control, press the "AUX" button.

   • After a few moments, the power button will light up. Continue to hold down the device button on the remote.
   • Keep the remote pointed at the device.

2. Hold down the power button while continuing to hold down the device button on the remote. The power button will turn off. Continue to hold down both keys for three seconds. The power button will light up again.

   Release both buttons. The power button light should be on. If not, repeat the steps above.