Menu
Is free
registration
home  /  Multimedia/ How to set up a programmable remote control. Programming the remote control for the gate and barrier

How to set up a programmable remote control. Programming the remote control for the gate and barrier

Programming remote controls for gates.Came, Faac, Nice, Dorhan, Profesional, Gant.

The first step is to register the remote control into the receiver on the control board. All manufacturers of gate automation have a different programming algorithm for remote controls, so there is no single recipe. Let's dwell on the main manufacturers of gate automation presented on the Ukrainian market - Professional (GANT), Came, FAAC, Doorhan, Nice.

First of all, a small educational program.

In Came, FAAC, Nice systems, one remote control is written to the drive receiver, and then the required number of other remote controls is copied from it. If you try to record the next remote control into the receiver, the first remote control and all remote controls recorded from it will stop working. If you have lost the old remote control, there is no need to delete it from memory - it will be erased by itself when you write a new one into the receiver. A huge advantage of such systems is convenience - there is no need to open the cover of the electric drive every time if it becomes necessary to record the next remote control. But this system is very vulnerable - I just need to hold your remote control for 10 seconds to steal a signal on my remote control. And this opens the gates to almost everyone who was holding your control panel (or the control panel of your employees). Let's say you decided to restrict access to the parking lot, put up a barrier and gave tenants 20 Came consoles (equal to the number of parking spaces). But after a couple of weeks there is not enough parking space again. Why? Because employees give each other remotes for copying and there are several times more of them than were given out. You can read how to do this below.

What is the way out? Install the system of Professional (GANT, China) or Doorhan (Dorhan, Russia). The main difference between such systems is that the signal of each console is recorded in the receiver individually. The downside is the limitation on the number of consoles recorded in the receiver (depending on the model, from 25 to 128 pieces) and the need to open the drive or receiver cover each time to record the next remote control. But such a system will not allow clones to be multiplied on the sly. Recommended for businesses and car parks with big amount users. You can't have unlimited trust in every single employee-user, can you? An advantage is the fact that the remotes of these manufacturers are also two to three times cheaper than the Italian ones.

How to program the Professional remote

How to program the Came remote

How to program the FAAC remote control

How to program the Doorhan remote control

How to program the NICE remote

How to program the remote Professional 100 UAH

Press the "LEARN" button on the gate operator control unit for 1 second, the "LEARN" LED will light up. Press the button on the key fob, the "LEARN" LED on the control unit will blink and go out. Your keychain has been saved.

If you need to record additional remotes, repeat this operation. It should be noted that a limited number of consoles are recorded in the receiver's memory (depending on the memory capacity of the microcircuit, the number of recorded consoles can be from 25 to 128 pcs).

To remove all key fobs, you must hold down the "LEARN" button for 8 seconds. All keychains will be erased from memory.

How to program Came 25 Euro remote control


It is necessary to press and hold the PROG (CH1) button on the control unit. The LED indicator starts flashing (left figure). Press the required button on the key fob. The LED indicator lights up with a steady light, which indicates the successful programming of the control unit (right figure). Release both buttons. The console is recorded.

Press and hold both buttons on the remote control you want to program (new remote control) (1). The LED indicator on it will start flashing quickly (2). Release the buttons and press the one you want to program (3). The indicator should light up with a steady light. In no more than 10 seconds, bring the master keyfob (programmed remote control) from below and behind to the programmed one (on which the indicator is on) and press once operating button(4). The LED indicator will flash three times (5) and extinguish (6). To program other remote controls, repeat the operation. Thus automatic system can be configured to work with any number of remote control transmitters with the same code.

How to program the FAAC 25 Euro remote control

To record the FAAC remote control into the drive receiver, you must simultaneously press two buttons P1 and P2 on the control panel and release them when the indicator on the remote control blinks (after 1-2 seconds). Then press and hold the button on the receiver board - the indicator on the board should blink.


While the remote control indicator is blinking, you must press the button on the gate control panel that needs to be programmed to control the gate leaf.Before releasing the receiver button, make sure that the diode is on for about 2 seconds (to confirm that the code has been saved). Now we release the button of the remote control and the receiver. The console is recorded.

But if you want to record more than one remote control, do not try to repeat this operation, as the next remote control (new) will be written to the receiver, and the previous one will be deleted. It is necessary to carry out the operation to copy the remote control. See below how to do this.

On the main remote control (recorded in the receiver), press and hold simultaneously the two buttons P1 and P2 and release them when the indicator on the remote control blinks (after 1-2 seconds).


Then place the copied (new) remote opposite the programmed one as shown in the picture above. On the main remote control (while the indicator is blinking), press and hold the button from which you want to rewrite the signal. Now press on the new remote control the button you want to program. The indicator should flash twice to indicate that the code has been saved. Let go of the button and repeat the operation for other proteins. Thus, the automatic system can be configured to work with any number of remote control transmitters with the same code.

How to program the Doorhan remote control

Before starting programming, it is recommended to clear the receiver's memory of the previously recorded remote control codes. To do this, after turning on the power, hold the record button of the remotes pressed for 10 seconds. The LED will blink for 10 seconds, then go out for 2 seconds and blink twice again to confirm that the remote control codes stored in the memory have been erased.

To write the remote control to the receiver, press and hold for 3 seconds the button for recording the remotes on the radio receiver board - the LED1 indicator on the receiver will light up. Then press the required button on the remote control for 2-3 seconds. To set up multiple remotes, repeat the procedure for other remotes.

How to program the NICE remote

NICE remotes are of two types - fixed code (blue body) and rolling code (black body)

The programming of the Nice Flo fixed code keypad is done by setting the two-position dip switches, both in the keypad itself and in the radio channel. Be careful - the variations must match. If you need an additional remote, simply spin up the old pre-programmed Flo remote and set the switches to the same position. These are old-style remotes, which are very rare today.

Let's take a closer look at programming remote controls with dynamic code.

Programming Nice Consoles with Rolling Code

Press the button on the receiver once (delay is less than 1 sec.). Press the button on the remote control for 3-4 seconds, after which the indicator on the receiver will blink 3 times. This means that the remote control has been successfully recognized and written to the receiver. After that, the receiver will be in the programming mode for another 10 seconds, during this time, by
if necessary, you can record several more remotes. After the expiration of the time (10 seconds), the receiver will remember all the remote controls assigned to it and all the buttons on each remote control.

You can also program the remote control remotely using a previously recorded remote control. As a result, the button of the "new" remote control will copy the command from the button of the "old" remote control. ATTENTION! Programming a new remote control from the old one must occur within the range of the receiver

Press the desired button of the new remote control for 5 seconds, then release, Press (without holding down) the button on the old remote control 3 times, On the new remote control, press the same button 1 time and release. The remote control button is recorded and performs the same commands as the old remote control button.

The remotes stored in the receiver's memory, if necessary, can be deleted. To do this, you need to carry out the following operations:
Press and hold the button on the receiver, You need to wait until the LED lights up 1 time, goes out 1 time, and then blinks 3 times, Release the button on the third LED flash.
If all operations are carried out correctly, then after a short pause, the LED on the receiver will blink 5 times.

Today in the world market there are many manufacturers who are engaged in automation. You need to be able to program it correctly so that the necessary technologies work well and properly.

Now we will look at the remotes from the gate. If you fine-tune them, you will protect yourself from intruders and make your life much more comfortable. Also, you can use the key fob not only to open the gate, but also for other devices. Let's take a look at how to program the gate remote control.

CAME control panels

This company occupies a leading position in the production of universal remotes. They can withstand a variety of climates and are easy to program.

TOP-432NA

The CAME company is considered the highest quality and most reliable today. You can find many good remotes from her. According to consumers, the highest quality model is the TOP-432NA. What is the reason for this? This remote control is two-channel, which allows you to work with several devices at once, namely, it is possible to open several devices at once, for example, a gate and a barrier. Its frequency is 433.92 MHz. This model is capable of working at a fairly long distance - 140 meters. How to program the gate remote control CAME?

  1. At the first stage, it is necessary to bring the remote control close to the gate.
  2. Next, you need to press 2 buttons. We hold them until the indicator light starts blinking.
  3. After that, click on any button, you just need to choose which one will be used for the gate. If the indicator starts to burn steadily and stops blinking, then you did everything right.
  4. We take the old remote control that came with the gate and click on the button to overwrite the code. It should be remembered that everything must be done quickly while the lamp on the CAME remote control is on.
  5. When the indicator on the new remote control blinks several times, dubbing will end. Now you can use it to work with gates.

Four-channel TOP-434NA

This remote is similar to the first model. The only difference is the size and number of fixtures that can be programmed. The frequency remains the same. TOP-434NA - gate remote control. How do I program it?

  1. As in the first case, you need to bring the remote control to the gate and press two keys simultaneously. We are waiting for the LED to light up.
  2. Click on one of the buttons to start recording on it.
  3. Then we press the button on the special remote control to rewrite the code.
  4. After the indicator blinks 3 times, you can start using this remote control. The data was successfully overwritten.

TOP-432EE

Recently a new keychain from the TOP series has appeared - TOP-432EE. It can work with devices that have been programmed with different encodings, such as TAM and TOP. To get started with this remote:

  1. It is necessary to press the key on the new key fob, which you want to use in the future to work with the gate. We wait until blinking appears on the indicator, and release the button.
  2. Repeat clicking on this button.
  3. After the performed actions, you need to quickly bring the old remote control to the TOP-432EE. Press the key on it, which allows you to open the gate. When the LED blinks 3 times, you can start using the device for its intended purpose.

TOP-432EV

This remote control is considered to be an improved version of the previous model. It has a fairly small size, which allows you to carry it in your pocket. Also TOP-432EV can contain 4096 code operations. How to program this key fob?

  1. As before, we hold down two keys until you see the light blinking. Then we release them and move on to the next step.
  2. We select the button to which the data will be moved.
  3. We are waiting for a few seconds until the LED lights up constantly.
  4. We bring the new remote control to the bottom of the other remote control and wait for the rewriting to be performed. This usually takes about 10-20 seconds. When the LED blinks 3 times, you can be sure that the recording has completed successfully.

Came twin

Another novelty is a keychain Came twin... It has one feature - code protection. Strangers cannot easily get hold of the code to open your gate. They are also produced in different variations- two and four buttons. Came Twin is capable of working with dynamic code. How to program the gate remote control?

  1. First you need to make sure that this key fob can already be used and that it has a button for receiving a signal.
  2. We bring the remote control as close to the receiver as possible.
  3. Next, we take the old key fob and press the key where the required code is written. We wait until the LED turns on.
  4. After 10 seconds, press the key on the old remote control.
  5. After about 20 seconds, the process of writing the code will end.

Nice firm

The Italian company Nice is in the top for the production of automated systems for various equipment. Their products are of sufficient quality and reliability. Of course they have universal remotes that allow you to manage some processes at the same time. How to program the remotes from Nice gate?

Nice FLO and FLOR

Nice key fobs are easy to program. All models in the FLO and FLOR line can operate with rolling code at 433.92 MHz. They can work even if they are at a distance of 140 meters from the desired object. Remotes are produced with one, two or four keys. Let's look at an example of how to program the Nice FLO2R gate remote control.

  1. First you should go to the receiver.
  2. It is necessary to arrange the consoles in sequence.
  3. Next, select the key to write the code and click on it.
  4. After 5 seconds, you can press the button that is used to open the gate on the old remote control.
  5. It remains only to repeat the keystroke on the first remote control. Button programming is complete.

Hormann

This is a German company that focuses on quality. Its products are quite reliable and beautiful. The manufacturer paints different buttons in different colors to determine specific frequencies for them (blue - 868 MHz, green - 26.975 MHz, gray - 40 MHz).

Hormann HSM 4

This model is equipped with four buttons that allow you to control various equipment. Hormann HSM 4 has a frequency of 868 MHz and the ability to use dynamic code. You can also note the rather small size of the key fob. How to program the Hormann HSM 4 gate remote control?

  1. We place the new remote control close to the old one.
  2. After that, it is necessary to press the key from which the reading will be made. We wait until the light comes on.
  3. Next, you need to press the key that you need to use in the future. After 5 seconds, the LED will flash quickly. Code transfer completed.

Hormann HSE2 and HSM

HSE2 has two-channel mode operation, and HSM - two and four-channel modes. It has a small size, which allows it to be hooked onto keys. The first model operates at 868 MHz and the second at 40.680 MHz. To program them:

  1. First you need to place the remotes close to each other.
  2. Take the old keychain and press the key from which you want to read the data.
  3. Next, press the key that you choose to use in the new remote.
  4. It remains only to wait for the blinking of the LED. We release the keys and we can start using this remote control.

Doorhan

Doorhan is a Russian company. It has entered the world market for a long time and supplies high-quality equipment for automation of work with gates and radios.

Doorhan Transmitter 2, Transmitter 4

These models operate with rolling code at 433 MHz. As you may have noticed from the name, key fobs can work with 2 or 4 various devices... How to program the Doorhan gate remote control?

  1. First you need to delete old records. To do this, press the key with which you can record, and wait. After 15 seconds, everything will be deleted.
  2. Next, you need to press the SW1 button (or any other that needs to be programmed) and on the old key fob to write data. We are waiting for a few seconds.
  3. This concludes the recording. You can start using it.

BFT company

The most common remotes from this company are BFT Mitto 2-12, BFT Mitto 4-12. They are two and four channel respectively. Able to operate at 433.92 MHz. How to program the BFT gate remote control?

  1. To transfer data, press the OK key.
  2. Next, go to the PARAMETER item and press the "-" button a couple of times.
  3. Repeat clicking on OK. After that, you will find yourself in a menu where you can add a device.
  4. Click on the AD start button and click on the required button.
  5. Next, click on the corresponding key in the old keychain and wait for the data to be overwritten.

Faac

This is a fairly popular Italian company. Its products are used in many countries around the world.

Faac XT2-868 SLH and XT4-868 SLH

These models are used to control two or four devices. The XT2-868 SLH and XT4-868 SLH operate at 868 and 35 MHz, respectively. They can also be used in various climatic conditions. How to program the Faac gate remote control?

  1. First, you must simultaneously press the buttons P1 and P2 to program the key fob.
  2. Next, you need to place the remotes together.
  3. As soon as the LED starts to light up, you need to hold down the key on the old device, which will be used in recording.
  4. In the new remote control, select the Slave button. After 15 seconds, recording will end. Then you can start using this remote control.

Conclusion

Today you can program the reviewed remotes for many devices. How to program the gate remote control? As you can see, this is pretty easy to do. In many remotes, the actions are very similar. To make everything go well, follow the instructions. You can choose the remote control of any company which you like best. Of course, you have to find the right frequency. This will important parameter when choosing a remote control.

Automation is a modern direction in production; very often, devices are used almost daily. The list of frequently used devices can also be replenished with gate remotes. In order for it to work properly, it is important to be able to correctly configure it, as well as, if necessary, carry out such a procedure as programming. Before you program the device from the gate, it is necessary to study some recommendations of the features. Thanks to this, all the work can be done independently, without the help of specialists, which makes it possible to significantly save time. Products of this kind are produced by many companies in different countries but there are a few worth noting. They are very popular, ranking first in the ranking of the best.

Gate remotes manufacturers

Several companies can be distinguished among the most popular manufacturers of automation on the modern market:

  1. CAME;
  2. Nice;
  3. Hormann;
  4. BFT;
  5. FAAC.

Any manufacturer uses modern technologies, due to which there may be some similarities in the work of the offered goods, but still more differences.

CAME control panels

An Italian company occupying a leading position in the world market. They produce a variety of automation products that ease the daily chores of a person. Each product is characterized by high quality, the accuracy of the work. Remote controls and locks of the company are affordable and can also be used in any climatic conditions. Performing all installation work requires a minimum set of skills, the main thing is strict adherence to the instructions. Any key fob has distinctive programming characteristics. Before carrying out the work, it is worth studying the instructions attached to the product.

Remote control - Came TOP-432NA model

The most popular model among a huge number of people. Such popularity is due to the fact that it is two-channel, which makes it possible to control a separate device to open a barrier, a gate. The product was manufactured using constant code technology. They are distinguished by small sizes - 32 * 68 * 13. The task can be completed up to 150 meters. Programming takes place in the following sequence:

  1. A working device together with a new one must be located at a distance of about 5 mm from each other.
  2. On a new key fob, you must simultaneously press two buttons, hold them until the indicator starts flashing quickly.
  3. We release both buttons, then press the one that needs to be programmed. In this case, the indicator should light up evenly.
  4. On the old remote control, you need to quickly click the key with which the reinstallation will occur. This manipulation is carried out until the new device starts to glow.
  5. If everything is done correctly, the indicator of the new device will blink three times. If this is not the case, it is worth repeating all over again.

Nice console

The company specializes in the production of automated systems specifically for gates, barriers, doors. The Italian company also holds a leading position in the world market. The products are of high quality, reliability and durability. One device can actually perform several tasks while staying at home.

Keyfob programming for Nice FLO, FLOR automatic gates

The device series is characterized by a rolling code frequency of 433.92 MHz. It is possible to perform manipulations at a distance of up to 150 meters. the dimensions of the products are relatively small. The line is presented in several variations of one-, two-, three-channel models. The programming is carried out according to the following scheme:

  1. First, the receivers are located side by side;
  2. All units must be arranged sequentially
  3. You must hold down one of the keys for about 5 seconds.
  4. The button of the old device must be clicked three times.
  5. Next, you need to press the button of the new device, which was previously held down once.

Hormann key chains for automatic gates

Time-tested German quality. The company's products are of excellent quality as well as attractive designs. The design is made in one direction, the product differs only in different radio frequencies. The differences can also be seen visually. The model equipped with blue keys is characterized by a frequency of 868 MHz, green - 29.975 MHz, gray - 40 MHz.

Hormann HSM 4 keychains

In private use, the Hormann HSM 4 model is very popular. Performs a four-channel remote control gates, barriers. Overall dimensions of the product are 37 * 110 * 13, radio frequency is 868 MHz. Has dynamic code.

programming the key fob for automatic gates:

  1. First, 2 devices are placed old-new "head to head".
  2. Hold down the key of the old key fob. The indicator should light up constantly.
  3. Hold down the new programming key. At first, the indicator light should flash slowly, and if the programming is successful, it will flash quickly after 4 seconds.

Keychain Doorhan

The largest Russian supplier of automation for gates, radios. Doorhan Transmitter 2, Transmitter 4 - a feature of these key fobs is also dynamic code. They are designed to control two or four automatic devices. They can also be used for any other equipment that is equipped with a company radio. Reprogramming involves performing the following actions:

  1. To reprogram the device, you must first clear the memory of old codes. After turning it on, you need to press the record key and hold it for 10 seconds. If everything worked out correctly, the indicator will blink for 10 seconds, then go out, then blink 2 times. This means that all the old codes have been removed.
  2. To write the required code, you must press and hold the SW1 button on the receiver board itself for 3 seconds. Then it is worth holding the device button for 2-3 seconds.
  3. Such manipulations should be carried out for each key, reflash the control code for a specific device.

Keychains BFT - product features

ВFT Mitto 2-12, ВFT Mitto 4-12 - respectively two- and four-channel remotes. The frequency of the products is 433.92 MHz. Programming the product is quite easy, you just need to perform a few manipulations:

  1. Press the "Ok" button, after which a greeting will appear.
  2. Press the button again and then the "PARAMETER" menu should appear.
  3. Then press the "-" button several times. The "RADIO" menu should appear.
  4. Press the "OK" button again, after that the next section of the menu for adding key fobs to the memory of the radio receiver "AD start" appears.

To encode key fobs, you need to sequentially perform the following manipulations:

  1. Click the "OK" button, the inscription "hidden button" should appear.
  2. Then you need to press two buttons on the key fob that you want to encode.
  3. The inscription “relise” should appear first, and then “desired button”.
  4. Press one key.
  5. "Ok 1" should appear, which indicates that everything went well.
  6. To carry out coding of other key fobs, the work must be repeated according to this scheme.
  7. After completing all the manipulations, you must simultaneously press the plus - minus 2 times.

Faac recognized as the leader in gate remotes

The Italian company Faac is recognized throughout Europe as well as all over the world. Some time ago, the XT2-868 SLH and XT4-868 SLH devices were very popular. The devices are two or four-channel, they worked up to 50 meters. Performance did not degrade with temperature conditions from -20 to +55 degrees. With their help, it is possible to remotely control gates or barriers. The frequency is 868.35 MHz. But they have already been discontinued, they were replaced by new models of the XT series. They differ more modern design, as well as improved performance. Transcoding of remotes can only be carried out if there is a master keyfob, the one that was recorded first, as well as a key fob where the recording will be made.

  1. On the old remote control, press the P1 - P2 buttons simultaneously for two seconds. Only if the LED flashes can you continue programming.
  2. Key fobs must be placed strictly opposite each other.
  3. In this case, the indicator should be on constantly. On the old remote, you need to click a button that should be overwritten.
  4. New remote control programming key. Release only if the indicator blinks 2 times.
  5. The coding was successful.

V modern world there are a variety of devices that allow people to do their jobs more comfortably. A universal key fob will allow, without leaving your home, a car to open a gate or a barrier to exit, it is convenient especially in bad weather conditions, and also to save time. Many manufacturers offer great amount variety of options. This will allow everyone to choose the most suitable option for a particular case.

All work on programming the device can be done independently, but if any difficulties arise, you should contact special service companies or service centers. Experts will help to eliminate all faults, to establish work. Also, you should go to specialists if the remote control starts to work poorly or does not execute programs. You cannot disassemble it yourself, this can lead to more significant damage.

In order to facilitate the process of controlling gates and barriers, radio remote controls are used. Recently, they have become especially popular due to their compact size and ease of use. That is why services such as programming remotes for clone and duplicate remote control gates are so popular. This is necessary if you bought a new remote control or want to reconfigure the range of the old one.

It should be noted that the independent settings of the new remote control are not always successful, for example, two channels are configured by mistake instead of one. From this comes the question of how to program the second key fob from the gate, clone, register and recode, or flash the key fob from the gate?

How to reset the gate remote control and reset the settings?

You can call us by phone and our engineer will professionally advise you and offer his assistance.

Why is it beneficial to use a radio remote control?

  • it is convenient, especially for large areas with many fences;
  • saves time if the gate or barrier needs to be opened many times;
  • the compact design allows you to carry the item with you everywhere.

What are the remote radio transmitters?

Today, two types are distinguished:

  • Radios with one fixed code - it is quite easy to program, but not too secure with the risk of signal interception.
  • Remote control with multiple signals. The codes of such a keychain can be changed, this ensures safety. Depending on the model, key fobs can support up to several million code combinations.
  • With Jumping Code.
  • There are also cards from the gate.

Our service center carries out programming of key fobs different models and complete sets as well as reprogramming of keys from the gate and we can delete the code from the key from the gate. We are also pleased to offer a versatile Jolly Open model that has no analogues. This remote transmitter can copy multiple original remotes with different codes, is reliable and easy to tune to many channels. Jolly Open is equipped with metal case and maintains programs even in the event of a low battery. Also pay attention to the Apollo-C remote control, which can replace 4 automatic remotes operating at different frequencies.

JollyOpen is compatible and can replace the following remotes:

  • CAME: TOP 432, TOP 434, TAM 432, TWIN 2
  • Beninca To.Go2
  • Nice - FLO series (FLO1, FLO2, FLO4), Very VE
  • Apollo-C
  • Ditec GOL4C
  • Dea MITTO 2
  • Roger R80 / TX12
  • Marantec D212
  • Dea 623
  • Gate-TX
  • Altonica

Delivery of remotes without programming

300 rubles (from 5 pcs. Free delivery in St. Petersburg)

Delivery with programming from control panel to control panel

1000 rubles

Delivery with programming via the automation radio channel (access to the gate or barrier control unit is required)

from 1500 rubles

Installation, replacement or connection in parallel (to expand the number of consoles) of the automation radio channel

from 3000 rubles (the price includes only work without the cost of equipment)

Catalog with remotes, prices and how to set them, see the next section>>> Gate remotes.

Contacts


Robust plastic housing
-high range
- 12V battery included
- light indication
- 12V battery included
-size 40x63x17mm

Encoding:

Press the button on the new key fob for 2 seconds.

Remote control two-channel MITTO 2-12 for CLONIX receiver

_____________________________________________________________________________

Beninka TO.GO4WV- four-channel key fob.

Dynamic code, 433.92MHz.

Designed to control automatics, with a BENINCA radio receiver.

Programming:

Press the hidden button on the operating key fob with a paperclip

Press the button on the working key fob

Press the button on the new key fob for 2 seconds

Remote control two-channel MITTO 4-12 for CLONIX receiver

Rolling Code Keychain CAME ATOMO, 433.92MHz for gates and barriers.

To program a duplicate key fob:

  • Position yourself in a zone of reliable reception, no further than 5 meters from the radio receiver.
  • On the operating remote control, press the button and hold it until the indicator lights up steadily (about 15 seconds).
  • Within 20 seconds, press and hold the button on the new key fob 1 time.
  • Wait 20 seconds until the radio exits the programming mode. Check the operation of the new key fob.

__________________________________________________________________________________

The 433.92 MHz radio series is specially designed to meet the latest automatic remote control standards. The TOP - NA version implements multi-code technology, that is, the ability to use an individual code on each of the buttons of each radio remote control.

Keyfob copying:

  • Press both buttons at the same time and hold until the indicator flashes faster.
  • Press the button to be programmed (the indicator lights up with a steady light).
  • Within 10 seconds, bring the working key fob from the bottom and back to the new one and press the button on the working key fob for a few seconds.

After writing the code, the indicator should flash three times, the key fob is ready for use.


____________________________________________________________________________________

Transmitter 4 DoorHan

Advantages:

  • ergonomic design;
  • 4 independent channels.

Remote controls Transmitter D2 are intended for remote control of DoorHan automatics or any other device to which the DoorHan radio is connected. One remote control can control four gates (barriers or other automatic devices).

Advantages:

  • ergonomic design;
  • KeeLoq signal floating code algorithm;
  • 16 million combinations of floating code;
  • 4 independent channels.

Compatible with all previous versions DoorHan key fobs.

________________________________________________________________________________

Key rings Ecostar Rse2 supplied by Hormann for Ecostar operators with Hormann doors. The receiver memory is designed for 6 remote controls. New keyfob programming:

  1. Press shortly the small transparent "P" button located on the drive cover or the "P" button on the receiver. The red LED light starts blinking, signaling that the system is ready to program the desired key on the remote control.
  2. Press the keyfob key and hold it until the red LED starts blinking quickly.
  3. Release the key.
  4. Within the next 15 seconds, press the keyfob key again and hold it until the LED starts blinking very quickly. Then release the key again.
  5. The end of a very fast blinking indicates that the selected keyfob button has been successfully programmed. The LED light is on without blinking.

After programming the keyfob and expanding the radio system, it is necessary to carry out a functional test.

Complete erasure of the radio receiver memory:
Press and hold the "P" button for more than 5 seconds.
All remotes are erased, it is impossible to erase one or several separately.

___________________________________________________________________________________

FAAC remote controls TX2 / 4

Designed to control FAAC or any other manufacturer's automatics when connected to an external FAAC receiver. A two-channel remote control (TX2) allows you to control two devices, a four-channel remote control (TX4) - four. They have the function of copying the code from one remote control to another - to add new ones to the system, there is no need to access the receiver. Each button can be programmed.

TX2 / 4 consoles operate in two modes: Master and Slave. The Master remote control can be used to write its code to the radio receiver (minidec) of the control unit, as well as to transfer its code to other Master remotes or Slave.

In addition, in the Master-panel it is possible to replace your own code with a new one (generated by the panel automatically).

The Slave remote control, unlike the Master, cannot be used to program other remote controls, to write its code to the radio receiver (minidec) of the control unit, and its code cannot be changed without using Mastera.

FAAC DL2-868SLH key fob is discontinued. Replacement: new FAAC XT4-868SLH key fobs. They differ only in design and improved performance.

Hand-held push-button transmitters (remotes) are produced in two and four-channel versions.

___________________________________________________________________________________

_________________________________________________________________________________

Single channel keychain Intro II 8501-1 for controlling roller shutters, gates, barriers, lighting devices in step by step("open" - "stop" - "close"). Miniature. Ideal for single site control. Power saving mode - turn off signal transmission if the button is held for more than 16 seconds. Used with receivers: Intro II 8513-50, Nero II 8713-50, Intro II 8513UP.

Programming procedure:

1. Enter the receiver into the programming mode, to do this, press and hold the receiver programming button for more than 4 seconds.

2. Enter the key fob into programming mode, to do this, press the key fob button three times in a row within two seconds, press and hold the fourth time until the LED starts blinking, then release it.

3. Write the code into the receiver, to do this, shortly press the key fob button.

4. Disconnect the receiver from the programming mode, to do this, shortly press the receiver programming button twice.

2 and 4-channel remote control for roller shutters, roller blinds, sun shades, lighting and other electrical loads in conjunction with Intro II series receivers.

1, 2 and 4-channel remote control for roller shutters, roller blinds, sun shades, lighting and other electrical loads in conjunction with the Radio series receivers.

Peculiarities:

  • connection of a safety sensor (photocells);
  • connection of an external switch or button;
  • connection to the control unit of a barrier, swing, sliding and sectional gates;
  • the ability to program 30 (1000 for Radio 8113 IP 65-1000) transmitters (remotes) of the Radio series into the device memory; 4 operating modes:
    1. short command (time of supplying voltage to the electric drive - 1.5 sec.), used most often for joint work with other automation devices;
    2. roller shutter mode (the time of power supply to the electric drive is set from 0.2 to 180 sec.), used to raise and lower the roller shutters;
    3. louver mode (the time of voltage supply to the electric drive is set from 0.2 to 180 sec.), used for raising / lowering and turning the slats of horizontal blinds;
    4. continuous command (voltage is supplied to the electric drive before the execution of the command "STOP"), used to turn on / off lighting, other electrical load

Keychain for controlling roller shutters, roller blinds, sun shades, lighting, etc.

4-channel.

The keychain is out of production. If you need additional Nero Sketch keyfobs, you need to install an additional radio module.

CAME, Nice, Hormann, DoorHan, BFT, FAAC are the main manufacturers of automation on the market. Let's dwell on each of them in more detail.

Products Italian company CAMEis one of the best in the world market. Thanks to their precise automation, life becomes more convenient and comfortable, as well as safer. Came devices are available, there are no problems when installing on any gate, and you do not need to change them, which greatly saves you money.

With regard to climatic conditions, it should be noted that manufacturers have approached this issue responsibly. The equipment perfectly withstands frost, wind, heat, dust, rain.

CAME control panels

TOP-432NA is the most popular. Due to the fact that it is two-channel, it is possible to control a separate device, for example, to open a barrier and a gate. Frequency 433, 92 MHz. Manufactured using constant code technology. Size -32x68x13. Works at a distance of up to 150 meters.

Programming keychain Came TOP-432NA

1. It is necessary to set the distance not more than 5 mm from each other.

2. Press two buttons simultaneously on the new remote control and hold them. The indicator flashes rapidly.

3. Release the button and press on the one that needs to be programmed. Now the indicator is on steadily, does not blink.

4. We turn on the key on the old key fob quickly, with which the rewriting will be carried out. All this must be done while the light on the new remote control is on.

5. If everything is done correctly, then the indicator on the "clean" key fob will blink three times. This indicates that the write was successful, that is, the code was rewritten.

TOP-432SA - two-channel, operates on two devices. Frequency 433, 92 MHz.

Copying the TOP-432SA remote control

1. The distance between the key fobs should be no more than 5mm.

2. On the new one, press and hold the button on which the recording will be made until the indicator lights up with a steady light.

3. When the button on the new remote control is lit, then you need to press on the other, from which the code will be rewritten.

4. The remote should blink three times. Everything was done correctly.



TOP-434NA - Four-channel keyfob with an operating frequency of 433, 92 MHz.

Came TOP-434NA programming


1. You need to press and hold two buttons simultaneously on the new key fob until the blinking changes.

2. The lamp is on steadily. Briefly you need to press the button on which the code will be written.

3. While the indicator on the first one is on, you need to quickly press the key on the second, with which you want to rewrite the code.

4. There should be three blinking on the new key fob, which indicates a successful result.

TOP-432EE is a new model of the TOP series. It works in two coding systems TAM and TOP, which allows working with consoles at those facilities where TOP and TAM coding was installed.

Programming with TOP-432NA


1. Preparation for programming. Press and hold the button on the first transmitter key fob that needs to be programmed until the indicator starts flashing. Release them on the new remote.

2. Click on the button. The indicator should light up without blinking.

3. Within ten seconds, you need to bring the key fob to the TOP-432NA, on which the light is on. Turn on the button on the master key fob once. The LED will blink three times and then go out, indicating successful copying.

TOP-432EV is an improved model of the TOP series. Contains 4096 code operations. 32x69x11 mm - overall dimensions.

Copying Came TOP-432ЕV keyfob from TOP-432NA

1. Press, then hold the top two buttons on the key fob to be programmed until the indicator starts blinking quickly. Now you need to release two buttons on the TOP-432NA remote control.

2. Press any key that you will be programming.

3. The light should be on with a steady light.

4. Within ten seconds, bring the TOP-432EV keyfob from the bottom and from the back to the TOP-432NA, where the indicator is on, press the TOP-432NA operating button once. Remote device ready to work if the light blinks three times.

Remotes - new products from Came, which are designed to protect the radio control code, illegal copying by outsiders. Two-button and four-button are available. Remote controls with a dynamic code system.

Came Twin remote control programming


1. You must have an already authorized key fob, which has already been entered in the system using the receiver button.

2. The location area should be no more than five meters from the receiver.

4. Within twenty seconds, press the button of the new key fob once.

5. We are waiting for about twenty seconds until the radio exits, from the so-called programming mode.

6. New code introduced. This procedure can be done with the following remote control. But very important: one radio receiver supports no more than 25 key fobs. Also turn off those receivers that are close, in which you do not need to enter a new code.

Came TCH-4024 and TCH-4048 are four and eight channel 40 MHz transmitters. Touch is a new generation sensor that allows you to control several objects. There is protection against accidental key presses.

Copying Came Touch Remotes


1. Press and hold the top two buttons at the same time until the indicator blinks faster.

2. Press the button you want to activate. The indicator will light up with a steady light.

3. Bring the working key fob from behind to the new one for ten seconds and press the (working) button, hold it for a few seconds.

4. The indicator should blink three times if everything is done without errors.

Came AT 02 and AT 04 - two-channel and four-channel with rolling code. Atomo is a handy, sleek remote that guarantees great job clients. Ensures the reliability of the outgoing signal.

Came Atomo remote control programming


1. Choose an area of ​​excellent reception, no further than five meters.

2. On the working key fob, press and hold the button until the indicator lights up steadily for fifteen seconds.

3. On a new device, hold down the button once for about twenty seconds.

4. We wait fifteen seconds and check the operation of the new key fob.

Nice

Nice company is engaged in production automated system for gates, barriers and doors. This Italian company occupies a leading position in the world of automation. Nice products are reliable, high-quality, time-tested.

The ability to control all processes (close the gates, open the shutters) with one remote control without leaving home.

Nice FLO 1, FLO 2, FLO 4 - rolling code remote control. Frequency 433.92 MHz. Response range up to 150 meters. Dimensions 72x40x15. Produce one-channel, two-channel, four-channel.

Remotes Nice FLOR 1S, FLOR 2S, FLOR 4S. Single-channel, two-channel, four-channel models are available. The radius of action is 150-200 meters.

Nice FLO, FLOR programming

1. There must be a receiver nearby.

2. The remotes must be placed in series.

3. Press any button on the new one and hold it for about five seconds.

4. Press the button on the old remote control three times.

5. Now, on the new one, press once the button that was already pressed at first and release.

Nice ON 1, ON 2, ON 4, ON 9 - rolling code remotes. Elegant appearance, small dimensions. Works in all weather conditions. There is a special ring for attaching to keys. The control frequency is 433 MHz.

Nice ON remote control programming

1. The two remotes should be touching at the top.

2. Press any button on the new keychain and hold it until the light on the old one lights up. We release the key, and the indicator on the second one should blink.

3. Press any button on the old key fob, hold on the new button until the indicator lights up.

4. Release the button on the old key fob. The indicator on the new one went out - this is the successful completion of the programming.

Nice Very VE is a two-channel console with a statistical code.

Nice Very VE Programming

1. Press two buttons simultaneously until the light remains on.

2. Press the top key if the first switch on the receiver is in the “On” position. Press the bottom button if the microswitch is in the “Off” position.

3. Point # 2 is repeated for all ten microswitches located on the receiver.

4. The LED will start blinking quickly if the tenth switch is turned on. While it is flashing, if the buttons are not pressed, then the code will be stored in memory.

Nice Very VR is a two-channel floating code keychain. Frequency 433, 92 MHz.

Nice Veri VR remote programming

1. There must be a remote control that is already recorded in the receiver. The first is always written to the receiver with a floating code using the receiver's button.

2. Within five minutes, we transmit the code by holding the button of the new remote control.

3. Press the button of the old device three times

4. Briefly press the button of the new remote control. All recording is complete.

Hormann - time-tested quality

German products. Reliability, convenience, beautiful design.

This manufacturer produces remotes with the same design, but with different radio frequencies. They differ in color of the buttons: blue (868 MHz), green (26, 975 MHz), gray (40 MHz).

Hormann HSM 4 is a four-channel remote control for gates and barriers. Overall dimension 37x110x13. The frequency is 868 MHz. Dynamic code.

HSM 4 Keypad Programming

1. Place the head-to-head trinkets.

2. Press the button on the old remote control and hold it. The light should be on constantly.

3. Press the programming button on the new remote control and hold it down. The indicator will flash slowly for about four seconds at first, and then will flash faster after successful completion.

HSE2 remote control - two-button. Key ring. The frequency is 868 MHz.

Hormann HSM 40.680 MHz. Two-button and four-button.

Hormann HSM 40 MHz Programming

1. Place the new remote control next to the old one.

2. Press the button of the old remote control and hold it.

3. Press the corresponding button on the new remote control. The LED should flash four times.

4. Release the buttons.

HSP4-C - remote control for gates and barriers. New design... Beautiful appearance... The frequency is 868 MHz. Dimensions - 48x48x13 mm. The number of buttons is four.

Copy HSP4-C Remote

1. Place the key fobs next to each other.

2. Press the button of the transmitter, which inherits the code and hold it for five seconds. The indicator should be on constantly.

3. Then we press the button that needs to be programmed on the new key fob, hold it down. The light will flash slowly for about four seconds, but faster after successful completion of the task.

4. Let go of the keys on both consoles.

Doorhan

Doorhan is a large Russian supplier automatics for gates, consoles, radios. Focuses on the global market.

Doorhan Transmitter 2, Transmitter 4 - consoles with dynamic code. Working frequency 433 MHz. Designed for remote control of two and four Doorhan automatic devices, as well as for any other automation with an existing Doorhan radio receiver. One key fob can control two (four) gates, barriers.

Programming Doorhan remotes with DHRE-2 receiver

1. We clean the memory of old codes. After turning on the power, we hold the record button of the remotes for about 10 seconds. The indicator will blink for 10 seconds, then go out, then blink twice. All old codes have been removed.

2. To write down the remote control code, press and hold the "SW1" key on the receiver board for 3 seconds. Then we press the button on the remote control for 2-3 seconds.

3. If the setting of other consoles is required, then the code will be recorded again.

You can program a specific control channel with each key.

BFT products guarantee quality and reliability

BFT -12, BFT Mitto 4 -12 - two-channel, four-channel remotes. Frequency 433.92 MHz.

Programming BFT remotes

1. Press the "Ok" button. A greeting appears.

2. Click the "Ok" button. We see the first section of the PARAMETER menu.

3. Now press the "-" key several times, the "RADIO" menu appears.

4. Press "OK" again and see that the menu section for adding key fobs to the memory of the radio receiver "AD start" appears.

To add key fobs you need:

1. Press the "Ok" button - the inscription "hidden button" appears.

2. Press on the two buttons of the key fob that you want to record.

3. "relise" appears followed by "desired button".

4. Press the button on the remote control.

5. "Ok 1" appears. Everything went well.

6. To record other keyfobs, we will do everything by analogy.

7. After all the remotes have been recorded, press the buttons twice<+>and<->simultaneously.

Faac is a recognized market leader in the production of automatic barriers, gates

The Italian company is known not only in Europe but all over the world.

XT2-868 SLH, XT4-868 SLH - two-channel and four-channel remote control for gates and barriers with 868, 35 MHz frequency. Works at temperatures from -20 to +55 C. Radius up to 50 meters.

FAAC DL2 868 SLH, FAAC DL4 868 SLH - obsolete models, discontinued. Two-channel and four-channel. The new XT series remotes completely replace the previous ones. They differ only in stylish design and improved performance.

Programming FAAC consoles XT2-868 SLH and XT4-868 SLH series

A master keyfob is required, that is, the one that was recorded first (master), as well as a new remote control (slave).

1. Press the P1 and P2 buttons on the old device for two seconds at once. The LED blinked, then you can start programming, since he saw this device.

3. The indicator is constantly on. Press the key on the old remote control to be overwritten.

4. Press the button on the slave panel for programming. We release the button after the light blinks twice.

5. All copying is complete. Actions can be done on all other buttons and other remotes.

In conclusion, I would like to say that nowadays, an automatic control system is installed on all types of barriers, gates, doors. It can be operated using a separate remote control, which greatly increases the level of security, especially against theft.

The automatic remote control is a pleasure to use. The main thing is that you can always wear it with