SAMSUNG DATA MIGRATION work description. Transferring System on SSD without reinstallation - Best ways

System transfer to SSD is effective method Computer organization.

Note, depending on windows version and parameters of the acquired flash drive, transfer methods may vary.

What data can be transferred to SSD

The storage of the operating system on SSD allows not only to speed up its operation, but also increases the response of other programs and files that are stored on the disk.

On the flash drive, the user can move the following data types:

• Operating system . It is added to SSD with all the ready drivers and settings. In fact, its duplicate is created, which was previously stored on HDD;
• Programs - Choose yourself which applications you want to add on, and which wish to leave on (HDD). We advise you to leave on the computer the volume programs for editing video and development / testing software - so they will work at times faster;
• User files . It can be any of your documents, photos, music, video and other data types.

Components for moving

To add the Windows used on SSD, the following objects are required:

If you work only with OS resources, you will not need to be installed fidewly utility.

Requirements for computer

Before performing any action on transferring OS, make sure that your device meets all the minimum requirements that allow the utility to interact with SSD and transfer large amounts of data.

Minimum requirements The following table is listed:

Compare the parameters of your computer with the above characteristics can be using the "System" window.

It displays the correct data on the main hardware and software components Device:

We use the built-in windows

Follow the instructions to transfer the operating system to the flash device:

• Open the window "Disk management". To do this, in the Perform window, write the diskmgmt.msc command and confirm the action;

Fig.3 - Running disk management tools

• Now you need to reduce the OS volume on the disk. You can perform an action using the "Compress Tom" function. All data will remain in the same condition, only the place occupied on the HDD will decrease. Click the right key to the "System" section, and then to "compress Tom";

Fig.4 - Compression volume

• After successfully reduced OS volume, a free section will appear in the disk circuit. This means that everything was done correctly;
• Connect the drive to the computer and restart the window "Disk management";
• Now click on the "Master" tab and select "Transfer OS SSD" list;

Fig.5 -Bext "Master"

• The standard utility will open. Press the "Next" key to go to the settings;
• Click on point "Unoccupied space" and go to the next window;

Fig.6 - choice of disk space

• Now you can independently change the size of the future disk or leave all the parameters unchanged;

Fig.7 - change the size of the disc partition

• After clicking on the "Next" key, the master will start moving the system. After completing the action, you can turn off the computer and the next time you select the OS that is on SSD.

Windows on the solid disk will also remain. You can delete it or use it as backupWhen you need to restore the system.

Fig.8 - the result of successful movement of Windows

Do not forget to click on the "Apply" key in the left side of the window. "Disk management"Otherwise, all changes made will not be saved.

If windows or hangs occurred during the transfer, you should reset the settings, restart the PC and try to transfer again.

Fig.9 - Application of changes

Instructions for SSD from Samsung

The company has released an official utility that allows you to quickly move the OS from hard disk on the purchased flash drive.

The utility is called samsung data migration. You can download it for free from the official website of the company (section "Memory" - "SSD") or with a disk that is in the configuration of the device.

The program's initial window is as follows:

Fig.10 - SAMSUNG DATA MIGRATION utility window

Immediately after starting the utility, connect to computer SSD. With the appropriate adapter. Click on the "Start" key.

Fig.11 - analysis of the disk with the installed copy of Windows

After analysis, the program will automatically determine the SSD connected to the computer and show it on the screen:

Fig.12 - reconciliation of the source and end disk

If the place that Windows takes on the HDD does not exceed the available place on the SSD, you can immediately begin the transfer by pressing the "Start" key.

The automatic movement of all components will begin. The procedure can take from 30 minutes to 1.5 hours, depending on the Windows version used.

Fig.13 - Successful system transfer

As a result, you will receive a notice of successful. Close the window and delete all Windows data from the HDD.

A plus using samsung Data Migration lies in simple interface. The program will make all the work for you and the maximum will reduce the likelihood of errors or bugs after the OS transfer.

What if at the analysis stage you found that the space for the OS lacks on SSD? In this case, you need to clear Windows from unused data and applications.

You can do this right in the SAMSUNG DATA MIGRATION utility window.

Fig.14 - Error. Not enough space on SSD

After the error text appears (highlighted in red), click on the "Next" button and delete all library files in the new window that litter the system.

Clean the OS until the text will appear in the main window of the utility. "Ready for cloning on SSD".

Fig.15 - Successful cleaning of unnecessary files

Utility Acronis True Image

Acrins is the most popular OS transfer utility for removable media. It recognizes all SSD brands. The application is supported by all versions of Windows, so there will be no compatibility issues.

Remember, you can use the application only if your PC hardware has a disk from the Acronis manufacturer.

There are no components - no utility will not start, and the user will be notified of the impossibility of working with the program.

Fig.16 - the main window of the Acrins application

Connect the removable media to the computer to move the system and in the program window, click on the tile "Cloning disk"-"Copying sections".

In the window that opens, select auto mode displacement. It is suitable for all tasks and quickly performs data copying.

Fig.17 - Select cloning mode

All sections will be copied to. All data that were on SSD to cloning will be deleted.

The disk itself will become bootable and can only be used to start operating systems installed on it.

Fig.18 - Copy Process

SEAGATE Discwizard utility

The utility completely repeats the Acronis interface. It should be used if you have at least one on your PC hDD From the manufacturer Seagate.

For cloning, you should perform the same actions that were described in the previous paragraph of the article.

Fig.19 - Main window Seagate Disc Wizard

Changing the bootloader configuration

After cloning the system, a copy of the OS will remain on the computer, and the window will appear with the load selection. After transfer, we advise you to perform a number of actions:

• Without deleting an initial copy from HDD, test Windows work on HDD. There are cases when the system begins to slow down, performance deteriorates. This occurs extremely rarely and depends exclusively from the selected SSD. While the first copy is not deleted, you will always have the opportunity to return to its use and delete OS with SSD;
• Change the system loader settings.

The download manager is the built-in component by which the computer determines which of the installed OS to run. Also, you can configure the order of running hardware components.

Immediately after the dispatcher will show two systems with identical names - initial and copied.

In the case of normal windows work On SSD, you need to remove the version that remains on the hard disk of the computer. Follow the instructions:

• Restart the PC and run the version that is moved to the flash drive;
• Open;
• Enter the following command below, setting a copy of the OS on the SSD unique name;

Fig.20 - command to rename the loader component

• Now configure the dispatcher in such a way that it always started the new OS. You can do this using the following command:

Fig.21 - automatic start cloned OS.

• To delete old system, enter such a command (where ID is the number old copy OS in the loader list):

Fig.22 - Removal of the original copy of Windows

Outcome

As you can see, to transfer the system to the removable flash drive, it is enough to use universal utility To duplicate components or move it yourself.

Do not forget to delete boot record disk that is no longer used. If this is not done, errors may occur while the OS is turned on.

Users who have suffered a SSD system mark an increase in computer performance and faster execution of complex tasks and processes.

The speed of the operating system is increased by 2-3 times.

Thematic videos:

How to connect an SSD to a desktop computer. Transferring Windows with HDD on SSD

Proper SSD disk connection to personal desktop computer. How to quickly transfer Windows from a hard disk (HDD) to solid State Drive (SSD). Practical advice, performance rating after replacing SSD.

Laptop Hard Disk HDD SSD Transferring System Free

Laptop hard disk HDD. SSD transfer Systems + system cloning program

The system transfer to SSD is an effective way to organize a computer. In addition, after buying a flash drive, you will not need to install on it from scratch and engage in setting all drivers. Moving to the disk is already existing system Allows you to save time and makes a PC disc for storing other files.

Along with Windows transfer, absolutely all programs, games, settings and drivers will be moved to SSD, which are already installed on the PC. You can solve the problem one of two ways:

• Using the built-in OS functions;
• Using third-party utilities.

Note, depending on the version of Windows and the parameters of the purchased flash drive, transfer methods may vary.

What data can be transferred toSSD.

The storage of the operating system on SSD allows not only to speed up its operation, but also increases the response of other programs and files that are stored on the disk. On the flash drive, the user can move the following data types:

• Operating system . It is added to SSD with all the ready drivers and settings. In fact, its duplicate is created, which was previously stored on HDD;
• Programs - Choose yourself which applications you want to add to SSD, and which wish to leave on the hard disk of the computer (HDD). We advise you to leave on the computer the volume programs for editing video and development / testing software - so they will work at times faster;
• User files . It can be any of your documents, photos, music, video and other data types.

Components for moving

To add the Windows used on SSD, the following objects are required:

• The installed utility for transfer;
• SSD himself;
• Computer or laptop;
• SATA-USB type adapter with which external disk Connects to PC.

If you work only with OS resources, you will not need to install a third-party utility.

Requirements for computer

Before performing any action on transferring OS, make sure that your device meets all the minimum requirements that allow the utility to interact with SSD and transfer large amounts of data. The minimum requirements are indicated in the following table:

Compare the parameters of your computer with the above characteristics can be using the "System" window. It displays the correct data on the main hardware and software components of the device:

Fig.2 - View window windows settings and computer

We use the built-in windows

Follow the instructions to transfer the operating system to the flash device:

• Open the Disk Management window. To do this, in the Perform window, write the diskmgmt.msc command and confirm the action;

Fig.3 - Running disk management tools

• Now you need to reduce the OS volume on the disk. You can perform an action using the "Compress Tom" function. All data will remain in the same condition, only the place occupied on the HDD will decrease. Click the right key to the "System" section, and then to "compress Tom";

Fig.4 - Compression volume

• After successfully reduced OS volume, a free section will appear in the disk circuit. This means that everything was done correctly;
• Connect the drive to the computer and restart the "Disk Management" window;
• Now click on the "Master" tab and select "Transfer OS SSD" list;

Fig.5 -Bext "Master"

• A standard utility for cloning operating system will open. Press the "Next" key to go to the settings;
• Click on the "Unmounted Space" point and go to the next window;

Fig.6 - choice of disk space

• Now you can independently change the size of the future disk or leave all the parameters unchanged;

Fig.7 - change the size of the disc partition

• After clicking on the "Next" key, the master will start moving the system. After completing the action, you can turn off the computer and the next time you select the OS that is on SSD.

Windows on the solid disk will also remain. You can delete it or use it as a backup when you need to restore the system.

Fig.8 - the result of successful movement of Windows

Do not forget to press the "Apply" key in the left upper part of the "Disk Management" window, otherwise all changes will not be saved. If windows or hangs occurred during the transfer, you should reset the settings, restart the PC and try to transfer again.

Fig.9 - Application of changes

Instruction forSSD. fromSamsung

Samsung has released an official utility that allows you to quickly move the OS from the hard disk to the purchased flash drive. The utility is called samsung data migration. You can download it for free from the official website of the company (section "Memory" - "SSD") or with a disk that is in the configuration of the device.

The program's initial window is as follows:

Fig.10 - SAMSUNG DATA MIGRATION utility window

Immediately after starting the utility, connect to the SSD computer using the appropriate adapter. Click on the "Start" key. Further, the application automatically scans the HDD used and display information about the remaining free place and sections of the carrier.

Fig.11 - analysis of the disk with the installed copy of Windows

After analysis, the program will automatically determine the SSD connected to the computer and show it on the screen:

Fig.12 - reconciliation of the source and end disk

If the place that Windows takes on the HDD does not exceed the available place on the SSD, you can immediately begin the transfer by pressing the "Start" key. The automatic movement of all components will begin. The procedure can take from 30 minutes to 1.5 hours, depending on the Windows version used.

Fig.13 - Successful system transfer

As a result, you will receive a notice of successful cloning of the operating system on the flash drive. Close the window and delete all Windows data from the HDD.

Plus, the use of Samsung Data Migration lies in the simple interface. The program will make all the work for you and the maximum will reduce the likelihood of errors or bugs after the OS transfer.

What if at the analysis stage you found that the space for the OS lacks on SSD? In this case, you need to clear Windows from unused data and applications. You can do this right in the SAMSUNG DATA MIGRATION utility window.

Fig.14 - Error. Not enough space on SSD

After the error text appears (highlighted in red), click on the "Next" button and delete all library files in the new window that litter the system. Clean the OS cleaning until the text "Ready to Cloning on SSD" appears in the main window of the utility.

Fig.15 - Successful cleaning of unnecessary files

Utility Acronis True Image

Fig.16 - the main window of the Acrins application

To move the system, connect the removable media to the computer and in the program window, click on the "Disc Cloning" tile - "Copying sections". In the window that opens, select the automatic movement mode. It is suitable for all tasks and quickly performs data copying.

Fig.17 - Select cloning mode

All sections will be copied to the flash drive. All data that were on SSD to cloning will be deleted. The disk itself will become bootable and can only be used to start operating systems installed on it.

Fig.18 - Copy Process

SEAGATE Discwizard utility

The utility completely repeats the Acronis interface. It should be used if you have at least one hard disk from the seagate manufacturer at your PC. For cloning, you should perform the same actions that were described in the previous paragraph of the article.

Fig.19 - Main window Seagate Disc Wizard

Changing the bootloader configuration

After cloning the system, a copy of the OS will remain on the computer, and the window will appear with the load selection. After transfer, we advise you to perform a number of actions:

• Without deleting an initial copy from HDD, test Windows work on HDD. There are cases when the system begins to slow down, performance deteriorates. This occurs extremely rarely and depends exclusively from the selected SSD. While the first copy is not deleted, you will always have the opportunity to return to its use and delete OS with SSD;
• Change the system loader settings.

The download manager is the built-in component by which the computer determines which of the installed OS to run. Also, you can configure the order of running hardware components.

Immediately after cloning, two systems with identical names will be shown in the dispatcher - initial and copied. If Windows is normal operation on SSD, you need to remove the version that remains on the hard disk of the computer. Follow the instructions:

• Restart the PC and run the version that is moved to the flash drive;
• Open command windows string;
• Enter the following command below, setting a copy of the OS on the SSD unique name;

Using the SSD drive instead of the hard drive enhances the speed and comfort of work, making reliable storage of information.

It is clear to the desire of users to change OC from the hard drive to the solid state drive.

How competently without reinstalling OC cloning information with all sections on a faster SSD drive?

How to transfer SSD system

See also: How to transfer Windows to SSD - 6 best migration programs

To transfer the system to SSD there are several ways. Consider each of them.

The first method is to transfer the user folder during installation.

For its implementation, follow the instructions:

1 In the installation process, at the parameter selection phase (step # 10), instead of selecting the use of standard parameters or their settings, press the combination keys Ctrl. + SHIFT + F3.

The computer will be rebooted into the so-called "Audit Mode" will log in to the built-in account "Administrator" .

3 After executing the previous step, you must simultaneously press the "WIN" + "R" keys. Opens command linewhere you need to enter "NET STOP WMPNETWORKSVC". After that, enter repeated in "% windir% \\ System32 \\ sysprep \\ sysprep.exe / Oobe / Reboot / Reboot / Reboot / Reboot" xml "

5 After completing the previous step, the user folder will be transferred to the desired SSD drive.

1. Create the answer file using the instruction that has been described in the number one method.
2. Run the system preparation tool in the same way as in the number one method.
3. Despite the fact that the system is already installed, when using this method, you will be downloaded in audit mode and primary system settings You do not need to enter the product key if such a request appears, simply click "Skip" .

You will not be able to log in to the previously used account, so at the user login step you will be asked to create a local account.

New account It will be used to implement the primary setting after the profile folder transfer and later it can be deleted.

Transfer OC C HDD on SSD

See also: Top 15 Windows disk defragmentation programs: Choose the best utility

Before cloning, it is necessary that the volume of SSD must exceed the one from which we plan to clone.

Aomei Partition Assistant Standart Edition

See also: Top 10 disk cloning programs: their advantages and disadvantages

First, we will analyze the cloning stages of OC with an additional applicationwhich offers an easy way to copy OC.

We offer to use for sample aomei program Partition Assistant.. The app is Russian-language in free access.

The functional program has a simple OC copy option to any disk. Download and install the program on your computer.

• Find on the panel section "Masters" located on the left and allocate the string " Transfer OC SSD or HDD ".

• A window opens with information about transfer, get acquainted with the message and allocate the tab . Follow the third step.

• Select a place where we will copy the operating system. Special attention must be paid to the fact that the drive must be not marked, there were no sections and, moreover, file SystemsOtherwise, in the end, it will turn out a clean list. After selecting the target disk, choose in the tab .

• Further action perform the markup of the drive, where we carry OC. You can adjust as needed, but remember that the volume of the selected partition should not exceed that OC is located. Here it is possible to assign the designation to the created section, if necessary. When all parameters are set, select the tab.

• Here the program recommends completing the installation of Aomei Partition Assistant application to copy OC to SSD Drive. It is proposed to explore the warning. After rebooting the OC may not boot. In this situation, be sure to turn off the former disk or change the drives. Certify your actions by clicking the tab "The end" .

• To start moving, press the button.

• A window opens with a list of deferred operations, click the tab .

• Additional post: By clicking on the tab "Yes" , I confirm all your actions. At the end of the reboot, the OC migration process will begin on the storage device on solid-state memory. The duration of action depends on several reasons, it is the size of the cloned data, the speed of the drive and the capabilities of the computer.

At the end of the transfer of information on the computer again there will be a reboot and you need to format the hard drive to remove the OC and the old bootloader.

• Works with all the carriers
• Free

• Average transfer rate

Regular tools of Windows

See also: "NTLDR IS Missing" - what to do? Solving a Windows Download Problem

Another option to copy the system to another drive to use typical Windows tools.

Perhaps this operation only when Windows is installed not lower than 7. Otherwise additional programs not enough. We will analyze the phased OC transfer on the example.

The OC Copy Operation itself is not difficult for typical means - performed in 3 stages:

• Create an OC image;
• Create boot disk;
• Haspasive OC image to another drive.

1. To reproduce the image OC use windows program . Open menu "Start" , later "Control Panel" .

1. Click on the string "Computer archiving" And begin to create. In the window "Archiving or Restoring Files" There are 2 necessary commands that will be used to form an OC image, and follow the desired link.

1. We choose where we plan to write the image of the OS. There are two options: disk and DVD section. It is notemly reminded that Windows 7, even without additional programs, has a large volume. And when solving copy OC on DVD, it is possible to recruit several drives.

1. Choose a place where the image will be stored, click on the tab. The program recommends choosing partitions for archiving. Since you do not copy anything other than OC, I do not do the choice, the system itself marked everything the desired discs. Therefore, click the tab.

- "Archive"

1. Confirm the desired archiving formats. We allocate the tab "Archive" And wait for the completion of archiving.

1. After creating a copy of OC Windows recommends making a boot disk.

1. Another way to create a disk using a string "Create a system recovery disk" in the window "Archiving or Recovery" .

1. Initially, the boot disk creation program recommends how to select a drive where you need to install a clean drive for recording. Click and go further.

If there are no typewriters in your computer, write on optical drive The image of the OS will not work.

1. If a disk with files, the system will surely ask it. If the disc is not formatting, use a clean drive.

1. To do this, open the window "My computer" And press the right drive. We celebrate the string.
2. Further actions on the formation of a drive for copying the OS, on the selected drive, press the string And wait for the end of action. At the end, the window appears:

We summarize. Created an image of the OS, as well as the loading disk for transfer, follow the final stage.

1. We put the computer to reboot, after graduation, go to the selection menu of the boot device.

This is usually done by pressing the F11 key, but there may be other ways.

1. Wednesday is loaded to restore OS. To begin with, we allocate the necessary language (in our case, Russian), we continue by pressing the tab "Next" . After that, start searching for installed systems.

1. Once the image of the OS is delan, we translate the switch to the second position and continue by pressing the tab.

1. Choose "Restoring a computer using the system created earlier" and continue by pressing the tab .

1. To establish as necessary extra options, Allocate the tab.

1. At the final stage, we will see a brief information about the created image. You can start unpacking, for this click the tab . We are waiting for the completion of the action.

1. The system is rebooted independently after the end of the unpacking. Windows transfer to SSD can be considered completed.

• Do not download.

• The transfer process is very complex