Login and password for ASUS RT G32. Configuring PPPOE Connection

The company ASUS (ASUS) products are widely known worldwide. The manufacturer delivers the most different market. computer technique, Including wireless WiFi routers. In this article, we will look at what you need to do to configure the ASUS RT-G32 router to access the Internet, and give an example of setting up a wireless network.

If you have just purchased a new router, you first need to connect the necessary cables to it. After unpacking the device from the box you will have a power supply and short network cable (Patchcourt). With meals and so everything is clear, but the cable will need to connect to one of the yellow-colored noddes from the back side of the router (LAN1, LAN2, etc.). The second end of the wire is connected to the network board on your computer or laptop. This is done in order for us to get into the modem settings.

The cable is not always required. You can connect to the router and via a wifi connection, but at the first stage it is better not to do if, of course, there is the ability to connect a computer with a device through a cable.

In a blue socket with the inscription "WAN", as you could guess, the "Internet cable" connects. This one cable that come to your home or office from the provider.

After the cable has been connected, it is recommended to reset the router setting to factory values. To do this, take a thin object and placing it into the hole with the "Reset" inscription, click on the button and hold it for 7-8 seconds. Usually, all indicators light up and then go out - this is the signal that the reset is performed successfully.

Now you can continue.

Login to Routher Web Interface

Like most modern communication devices, the ASUS RT-G32 router has a web interface. To get inside, it is enough to use any Internet conductor that you only have - Opera, Internet Explorer. or any other.

In the address bar of your browser, you will need to keep the IP address of the router. If you reset the device settings, the IP will look like "192.168.1.1". We write it to the Internet conductor and click the transition button.

If you do not work in this address, it may be a consequence of one of two reasons:

• Your device has a different address. Usually, if the settings are resetting successfully, the router receives the factory value of the IP address. You can try to repeat the reset procedure again.
• Network installations of your computer do not correspond to the router settings. Here you will need to reconfigure the IP address values \u200b\u200bof your connection by local network. For each operating system, this is done differently.

The web interface is usually protected by login and password - you will need to enter them. By default, both of these values \u200b\u200bare admin. We write a login and password to the appropriate fields and press the input button.

If everything goes successfully, you will fall into the ASUS RT-G32 web interface. Here the router will be prompted to perform settings in automatic modeBut it is better to do it yourself. To do this, click the "Home Page" button from the bottom of the page.

To connect to the global network, the ASUS RT-G32 router can use several types (technologies) compound

You can only find out what you need in your case, you can only at your provider. Information should also be listed in the contract with your Internet provider.

After you find out the type of connection, go to the WAN web interface point. Here in the Wan Connection Type drop-down list, you will need to select one of the communication technologies and make it setting. Consider every.

Dynamic IP.

This communication technology does not need any configuration. Just leave all the settings as it is and press "Accept". However, let's say in advance that this type of connection is not used by virtually any Internet service provider.

Static IP.

This type of communication involves entering network addresses, which are issued by the Internet provider individually. As you can notice, it is necessary to register values \u200b\u200bin 5 of the following fields (see picture below). Make it, scoring the address to each field corresponding to the address that is issued by your provider, then click "Accept".

PPPoe

This technology involves the use of authentication data (login, password), also issued by Internet providers. In addition, some providers additionally provide customers with static IP addresses. If all the data in your hands, fill in the fields according to them:

• To start, enter the authentication data in the appropriate section of the "Account Setup" section.
• If in your case the provider uses static addresses, move the switch in the "Configuring IP Address" section to the YES point and fill in the fields in accordance with the data provided by you.
• As a value of MTU, contribute - 1472.

Click "Accept".

PPTP.

PPTP connection type settings are exactly the same as in the previous case, for only exception. Here you will additionally need to register the VPN address in the HEART-BEAT server field. This address should also be provided by your Internet service provider in the form of an ordinary IP address (or, in some cases, in the form of a domain name). Fill everything in accordance with the picture below (naturally, pointing to your values) and click "take."

Immediately after you set the settings to enter the global network, it remains to configure Wi-Fi

Go to the Modem web interface to the tab " Wireless network" Here you need to specify values \u200b\u200bfor the following fields:

• SSID is essentially the name of the network that is displayed in your phone or computer when searching for free WiFi. Enter here, for example, "Moy_Vayfay" or something like that.
• Learning below there is a "Hide SSID" field. If you check the tick on "yes", your network name will not be displayed when searching for networks - in this case you will need to enter it manually in the settings of your communication device. It is better to leave a tick at the point "No".
• In the lists marked in the figure below as "2", select the appropriate values.
• The bottom field is designed to set the password to which your WiFay network will be protected. This should enter a value that has a length of at least 8 characters and, it is desirable, containing both letters and numbers.

After all the procedures are completed, you will need to restart the router, which can be done by clicking on the appropriate button.

In contact with

If you wondered how to connect the Asus router with a computer, and how can it be customized, then this article is created for you. First, to perform the connection you will need a special cable, called patch cord. Usually, this cable goes to the configuration along with the router, it serves to connect a computer and modem if the connection was executed, in the settings of the network connection it is worth viewing whether there is access to the network.

The first step is a network connection and its configuration.

You need to go to "Network Management and common access"To do this, go to the Start menu, and choose the" Control Panel "there. It is there that will be the corresponding section that we need when you were in it, it is necessary to find that connection, which is active, and right-click on it, go to the "Status" tab.

When a new window appears, you must select "Properties", and there to find such an item as "Internet version 4 (TCP / IPv4) 2" and switch to its "Properties". Naturally, after that, it is immediately necessary to go directly to the setting, it does not need to carry out many manipulations, it is enough opposite each item with a value automatically put the bird.

If it was so standard, then it means there is no need to make any adjustments, it is enough to leave everything in your places, close all the windows, and go to the second setting item to your router.

The second step is to connect the cable from the router to the computer.

After viewing the device on the back, you can see connectors such as LAN (yellow), WAN (blue shade), Power (black). You need to connect the power supply to the POWER connector, the Patchcord is inserted into the LAN port, which is inserted with the device (the second end of the wire is inserted into the computer), but you need to connect a cable from the provider of your Internet into the WAN port.

Third stage - setting up the modem.

In order to continue to configure the modem, you must start the browser, and drive 192.168.1.1 to the ENTER key and press the ENTER key. After that, the page will be opened where you need to enter a login and password of access. Standardly they are installed as "admin", "admin".

If you first enter this panel from your computer, then a similar dialog box will pop up.

If you click on the "Home Page" button, you will automatically enter the main page in which you will need to select the control panel interface language and configure the wired connection. If this is not done, then wireless connection Set up, will not come out. To start acting, you need to go to the tab with the name WAN and choose "Internet connection" there.

Now proceed directly to setting up our Internet.

In the connection type, you must select the point with the name - PPTP.

Opposite the item - setting up DNS WAN, "you need to install a tick in the" No "position, because these settings will need to fill on your own, for this you have to call the provider, wondering these data.

The Account Block must contain information about the login of the Internet and its password. This information should be provided to the Internet provider at the conclusion of the contract.

Apply all actions, and we get ready, workable internet connection.

The fourth item is to configure the wireless connection.

Due to the fact that it is not entirely convenient to work with the Internet connection on the cable, it has long been developed by such a technology as "Wi-Fi", it allows you to access the Internet without a cable, for this reason, this is called "Wireless Internet Connection " Now, we will do small manipulations that allow you to configure the wireless data transmission on the router.

On the main page Control panels need to select the item, with the name "Wireless Networks". Further go to the tab, called "General", and there it will be necessary to fill these by handles. The SSID field - requires the name of the network. You can choose absolutely any name, because it comes from your brain. Now you need to take care of the protection of the created network. To do this, in the "Authentication Method" item, you must specify the setting with the name "WPA-2 Personal". The encryption type can be selected both combined and AES. Next, enter the password that will be requested while connecting to the wireless connection. It is necessary to install such a password that will be reliable, but it is necessary to never forget it, otherwise you will not be able to connect to your own network, and you will have to reset the settings to factory settings.

After doing these actions, the setting ends, you need to save the result, for this press the "Apply" button, it is located at the bottom of the page. After that, reboot the modem, and we are convinced that everything works correctly. We advise you to check the performance not only on the computer, but, for example, on the phone, tablet, and so on. The configuration process is not complicated, and even a beginner can do it.

Good day Dear readers. Today we will analyze how to configure the Asus RT G32 router literally on the knee, as experienced uncle, well, and aunty. So, proceed.

I understand that we have already bought this router and the Internet is connected from your favorite provider. The first thing we need patchcord (most firms, including ASUS, put it in a box with a new router).

Overall setting of the ASUS router

We take our router in the handle and proceed to its configuration. First get out of network card Your computer is a cable provider and plug it into the WAN port on the router, and the new cable is in the first LAN port. The second plug stick into the computer's network card. This method Used with the ASUS RT G32 model, and with any other router or router:

Wire connection circuit

Next you need to configure the receipt of the IP address on the network card. ASUS device will display an address automatically. Therefore, in Windows XP, we perform right click on the tray icon, select the "Status" clause, click "Properties" and the Item "Internet Protocol (TCP / IP)" - then you need the "Properties" button:

Setting up a network card

IN address line The browser is typing the IP address that is usually specified on the back of the router box - 192.168.1.1, as well as the Login (Admin) and Password (Admin), which are suitable for any ASUS devices. Your WiFi router RT G32 must display a page:

When you first turn on, ASUS offers nothing to configure anything:

Automatic setting

We do not agree with the ASUS proposal and make the transition "Main page":

Main page settings

We assign the right language of the interface (then the router settings will be given from the calculation, which is selected the Russian interface language). The ASUS RT G32 router is mostly set up on the General tab. Different providers use different protocols: PPTP (Rostelecom), L2TP (Beeline). Before configuring the ASUS RT G32 router, Rostelecom should issue seven parameters:

1. On the WAN tab in the WAN-Connection Type field, select "PPTP" - no parameters here;
2. In the "Configuring WAN IP Address" and "DNS WAN Setup" set the "No" checkbox and put the data on the above partitions that your provider issued to you (IP address, DNS address, subnet mask, gateway);
3. Also specify the username and password as written in the contract.
4. Carefully reinfeit to the "Special Internet Service Supplier Requirements" section: In the HEART-BEAT or PPTP / L2TP server field, specify the parameters you want to specify with your provider by calling the support service. Otherwise, the router will not be able to create a VPN connection in principle. ASUS support service, i.e., the router's manufacturer, here. By the way, the router can be assigned to the MAC address of the computer, but it is not required for everyone.

customize WAN-port

If we talk about L2TP, letters and numbers will be less.

A small example. When in practice, the ASUS RT G32 router was performed. Beeline for some reason reported one word! It was the name of the VPN server. That's right: the login and password are specified in the contract, and the DNS and IP will be automatically obtained (the "Yes" checkbox in the "2" list).

Setting up a wireless connection

In theory, the ASUS RT G32 router works on the N150 protocol despite the letter G in its name. So, ASUS needs to work on the names. ASUS RT G32 has features:

1. On the General tab of the main page of the router, choose the "Wireless Network" item. In the SSID field (network identifier), specify how to be called wireless connectiondrowned by router. You can give a network name ASUS RT G32, but, in general, any name is suitable. The "Hide SSID" fields check the "No" checkbox.
2. Authentication method - select "WPA2-PERSONAL". Encryption WPA -Select "AES". So we would do with the RT N12 router, and in general, with any ASUS device, where the AES method is implemented.
3. Come up and enter the password. Tip on the right talks about reliability. Your ASUS RT G32 router uses up to 8 digits and letters, but only English.

Leave the remaining values \u200b\u200bby default:

Wireless network

Click "Apply." No more required! We looked at how to configure the ASUS RT G32 router so that he "distributed Wi-Fi." Now you need to configure a network card on a PC or laptop. I hope the reader understands that it should be a Wi-Fi card. Turn it on, and if it is already enabled, an alert will appear in the tray that the network is detected:

Wireless networks detected

The ASUS RT G32 router is now fully configured. Laptop or computer is not configured. Therefore, it is necessary to click on a new icon and in the window that appears to select one connection (for example, ASUS RT G32 is a SSID of our router). Having found the necessary network, click on the name right-click and select the Safety tab. Here set the encryption method and password:

Encryption method

As remember, our router Asus RT G32 is configured to WPA2-AES. The same choose and here - the network is already working, the router "distributes" it!

Video with wireless setup

Further will be considered how ASUS RT G32 is configured for specific applications. It will be about the DC ++ file sharing network, but not only. Know that the ASUS RT G32 router allows you to connect to a computer via RDP (remote desktop). What we will do, and also try to update the firmware yourself.

How to configure the connection to the DC ++ client

When the Internet connection works through a router, for example asus or d-link, only it is delivered to the addressing, and not a network card of the computer. The router assumes Internet requests and redirects them to the IP address that he dynamically assigned to the network card. Because of this, in some applications, such as the file sharing client DC ++, problems arise with access to the service. This property has any router, and the ASUS RT G32 model will not be exception. On the router you need to perform several manipulations - namely, to carry out the ports of the ports, i.e. Configure the correct operation of the network with your router, and the router with a computer. So, proceed.

In order to start a "port forwarding", you need to find a special tab. In the ASUS RT G32 router interface, the WAN menu contains six tabs. The above was considered how to open the first of them. Explore the beginning of the article and do the steps to the "Step 1". Will remain go to the tab " Virtual server"This is one of the tabs in the" WAN "menu (in the left side of the window):

Wang Port Setup

In this menu, you can create rules for the redirection, although ASUS has sewn into his router ready templates. Make sure that the checkbox is "Yes" in the "Enable Virtual Server" item. Now you can proceed to configure the wrong router, but the client.

In the DC ++ connection settings, select the "Firewall with manual redirection" mode. In the case of a file sharing inside the network in the "External / WAN IP" field, you need to enter the address that is valid for the local network of the provider - this address is assigned a router WAN port. If the DC ++ client goes to the external Internet, you will need to specify your dedicated IP address (refer to the provider).

In the "Ports: TCP and UDP" field, you need to enter port values \u200b\u200bfor which you plan to further work DC ++. It is better to choose one value that is easy to remember, but it is not occupied by the system. Take advantage of:

• Port (TCP / IP)

DC ++ setting

After all actions, we will return to the adjustment of the router - namely, to graphic interface ASUS RT G32.

Setting the route

On the router in the "Service Name" field, specify the name of our rule - for example, "DC ++" (optional). Then in the "Port Range" field, specify the value of the port from which you want to redirect external traffic to the internal network behind the router. In the "Local IP Address" field, you must specify the value of the IP address of the PC on the local network. You can find out this IP address in the "state" connection, and the same numbers you specify in the ASUS RT G32 settings:

We look at the property

In the Local Port field, you will specify the port value that is configured in the computer (port in the DC ++ client). In the "Protocol" field on the router, you must specify which type of traffic (TCP, UDP or everything will immediately) will be used. We choose the option "Both", which means both. At the same time, the router will create two rules for TCP and UDP. In the "Protocol number" field, you can enter any digit - the option does not affect anything. This is true for all routers in principle, including for ASUS RT G32.

To allow working with a remote desktop, the router is set up the same as for a computer with a DC ++ client. But in the "Local Port" field, on the "Virtual Server" tab, specify a specific value - the port number in which it works rDP protocol. This, of course, is about the port of TCP 3389 - it is used by default. And the router will not be able to prevent RDP Protocol Services.

We flash the router for yourself

What is the firmware of the router, everyone knows, well, and who does not know, he even guesses. Firmware is special programthat helps any device, in this case, the router, work. Update the firmware is required then to improve the performance of the router, correct the hidden errors, etc. All firms, including ASUS, are constantly developing their software, which is necessary for development. functionality Technique. For the device ASUS RT G32, the firmware is on the ASUS website. No need to download "pirated" drivers and firmware, hacked by homegrown hackers. Who will pay this ban, will get an unpleasant effect - overheating. True, the ASUS RT G32 router is designed without errors - it does not even overheat with the "pirate" software. The firmware version of your router can be found in the Web interface. Open the interface, as considered - the ASUS firm placed all the information at the top of the page:

Additional settings

Knowing all the numbers, that is, the firmware version, we can either download and install a new one, or leave the old one. It is necessary to find out the hardware revision of the router - the letter C1 or B1 company ASUS prints on the sticker. There are no other revisions from the RT G32 model, and the firmware for them is available on the ASUS website:

Page for download

The site of ASUS offers to select an operating system. I think you know what you have operating system Installed, pay attention to the bit (32 or 64). After that, a window will appear in which the firmware version has to be selected. Recall the numbers specified in the router interface:

Download the desired file

After downloading new firmware It is necessary to install it. On the main page, select the "Administration" item and the "Firmware Update" tab. At the bottom, next to the program version of the program, click on the "Overview" button and select the ASUS file that downloaded. In the window that appears, you must click "Open" and then click "Send":

Update software

Starting the installation of a new firmware to your router:

Update process

Attention! While will "fill up" the firmware, the router itself can not be turned off, otherwise it can cry out. Namely, the ASUS firmware will be installed incorrectly, and the router will not work correctly. For aSUS models RT G32 provides for errors, but get at the "brick" output instead of a router is possible. When the firmware fell, it is best to wait a minute two and restart the router forcibly: on the back panel at the ASUS devices there is a "reset" button, which is "drowning", and here it is necessary to start it for 5-6 seconds - the router will go out and restarts.

Reset button

The setting is 100% executed. For the ASUS RT G32 router, the characteristics are selected so that it is possible to operate this device and at home, and in the office: any LAN-port can be used as a WAN port, but, alas, not with the company aSUS firmware. Most routers from the Router RT family do not even differ even by this property: the WAN port burns, and - hello, how would you lose the functionality of the router and get the "access point".

ASUS is not the only one that produces routers with the possibility of LAN-WAN substitution. It is necessary to look at the chipset model - for the RALINK RT3050F and RT3052 microcircuits, the possibility of substitution is provided. Let's call all models of routers with one of these chipsets:

• ASUS RT G32 both revisions;
• Not ASUS: D-Link DIR-300 / NRU (B1-B4) routers, also DIR-615 (D1-D4);
• The DIR-620 router (revision is not known).

ASUS firmware can not be installed on router D-Link. The opposite is also fair. But "Pirate firmware" work on all routers: ASUS does not overheat anything, which cannot be said about D-Link devices.

Back in 2009, the sales of the ASUS RT-G32 router started. Its configuration is a fairly simple operation, and with it, we can cope with a novice computer specialist. It is its order for different operators and will be given in this material.

Niche router

By the standards of 2009, the considered router could be safely attributed to network medium-level solutions. Now the requirements have changed significantly, and only the most budget devices can be attributed to the ASUS RT-G32 considered under this article. The setting is certainly quite simple, and it does not arise with it any problems. Key advantage This budget router is its value that is currently 1000-1200 rubles. Taking into account the fact that this product is already tested by time and managed to show itself mainly only with a good side, this price is quite justified.

Specifications

Typical technical plan parameters for network solutions initial level ASUS RT-G32 boasts. WiFi Setup In this case, the standard, and nothing is superfluous in it. Number of wired ports in this device 5, and all of them - RJ-45. One of them is blue and has a WAN marking. The maximum speed in this case can reach 100 Mbps. It is to it that the wire from the network traffic provider is supplied. The remaining four is yellow and are labeling from LAN1 to LAN4. Connect to it local devices This network, to the number of which can belong to game consoles, televisions, computers, laptops and other equipment. As in the previous case, the greatest value of the transmission rate is 100 Mbps. One round jack is designed to connect an external power supply. Wireless part of the network is implemented using wi-Fi standard. At the hardware level, it is implemented by one antenna, and the transmission rate in this segment can reach 150 Mbps.

First Stage Settings: Connection

At the first stage, the ASUS RT-G32 is fully connected. Setting up for all providers identical. First you need to connect the power supply to the network alternating current and the corresponding jack of the router. Then sum up the cord from the provider and connect it to the port with WAN marking. Finally, if necessary, connect all wired devices computing network to the router. Separately, it should be noted that the email to any LAN port must be connected to the router to configure. And it can be like stationary computerand laptop. After completing the setting, this connection is not required, and it can be dismantled on the equipment off. In the future, it can be replaced with a more convenient and practical Wi-Fi.

Setting order for Beeline

To begin with, consider the order of configuration for the Cable Provider "Beeline" of the ASUS RT-G32 router. The Beeline setting requires the task of such parameters:

1. After switching on and ending loading such computing system components as a router and personal Computer, on the last launch any browser that is in stock. In its address bar, type the device address: 192.168.1.1. Click after that ENTER.

2. Then you need to wait for the termination of the control panel. In this case, two active fields will be present in the interface. One of them is "login", and the second is the "password". In each of the fields, you must enter the ADMIN symbol set. After filling in both fields, press the "Login" button.

• "WAN-connection" - "Dynamic IP";
• if necessary, we specify the port to which the IPTV prefix is \u200b\u200bconnected;
• in the next field, indicate that the IP address is set automatically and is obtained from the provider;
• then you specify an automatic connection to DNS.

4. After that, we save the changes made by pressing the "Apply" button and wait for the end of the network node reboot.

5. After the router is downloaded, select the "Network Map" item. In it, we must specify such parameters:

• the name of the network is set at its discretion by Latin letters;
• subparagraph Security LEVEL - in the drop-down list, select WPA-Personal;
• in the next embryption drop-down window, set the TKIP + AES value;
• next, in the Key field, specify a password for connecting at your discretion; It may consist of Latin letters and numbers - there must be no less than 8.

6. Press the "Apply" button again and wait for the end of the device again.

7. After that, ASUS RT-G32 is properly configured. Configuration "Beeline" - connections completed.

Algorithm for MTS

Not so much is very distinguished by the settings algorithm for the MTS network router ASUS RT-G32. Setting up MTS, as in the case of Bilayin, starts from entering the setup menu for the previously outlined method. Then in the menu item called "Advanced Settings" Select the WAN subsection. It sets such parameters:

1. Connection type - RPRoy.
2. Automatic receipt network Address and DNS.
3. We specify the username and password that are listed in the contract with the cable provider.
4. If necessary, also specify the LAN port to which the IPTV television console is connected.

We save these parameters and are waiting for the completion of the reboot of the router. After that, it is necessary to configure the wireless connection on the same algorithm itself, as in the case of Bilayin.

Configuration for Rostelecom

In this case, the order setting is identical with previously shown for MTS. And the basis of this is the same protocol RPRO for ASUS RT-G32. Setting "Rostelecom" requires the same actions. The only thing you must not forget about is that the password and, of course, the login is introduced from the Treaty.

RESULTS

One fact that the network router considered in the framework of this material has been successfully sold for more than 5 years, speaks of many things. For the world of electronic technologies, this is a whole era. At the time of the start of sales, this decision was related to the average level. Now ASUS RT-G32 belongs to the budget segment. Setting - a very simple simple operation with which it is forces to accurately cope with even a novice and poorly prepared user. For this, only enough to fulfill everything before specified steps For each operator.