Menu
Is free
registration
home  /  ON/ How to reset the control panel from the barrier. Universal gate remote control how to program

How to reset the control panel from the barrier. Universal gate remote control how to program

Programming of An-Motors AT-4 consoles for gates and barriers Construction. Classic AT-4 with red LED. Outdated models with blue LED.
Working frequency 433.92 MHz. The code is dynamic.

A 27A, 12V battery is used.

There is a protective silicone membrane.

1. If there is access to the control unit of the barrier. And so you have the right to open the cabinet and the key to the lock.

Then open the cabinet door. The control unit box (CU) is mounted on the door, from below. Remove the cover of the block, which is attached with four self-tapping screws. Disconnect the loop going to the cover. You don't have to disconnect. The long train allows you to neatly position the cover side by side.
Everything. Configuration access obtained.
Find the "LEARN" button.
In the photo marked with a yellow arrow.

Programming via the "LEARN" button. Click the "LEARN" button. The red LED will light up. Release "LEARN". Press any button on the remote control. The red LED will blink and turn off. That's it, the recording was done. Caution! If …

How to copy the Doorhan Transmitter 2 remote control (4)

How to make a clone of the Dorhan remote control from a barrier, gate Introduction Manufacturers of Doorhan automation for gates and barriers put built-in receivers in a control board with memory for only 60 subscribers. Of course, this is often not enough. Then an additive from this company is installed - an external receiver DHRE-2 (1).
So these DHREs are new and old.
New ones appeared in 2016, and the old ones continue to be released.
In both cases, you can make a duplicate.
Copying the Dorhan key fob registered in the receiver of the old model Old model DHRE-2 It is still in warehouses and on sale.
It means it is installed.
Supply voltage - 12/24 Volts. Receiving frequency - 433 MHz. Memory - 115 Transmitter key fobs. Inexpensive Chinese copiers Four channels. Code recording 433.92 MHz. Battery - 27A, 12 Volts. Video instructions for copying A simple procedure on the topic: do it yourself.

Cloning the Dorhan remote control assigned to the new DHRE receiver There is a separate article about this

Automation is a modern direction in production; very often, devices are used almost daily. The list of frequently used devices can also be replenished with gate remotes. In order for it to work properly, it is important to be able to correctly configure it, as well as, if necessary, carry out such a procedure as programming. Before you program the device from the gate, it is necessary to study some recommendations of the features. Thanks to this, all the work can be done independently, without the help of specialists, which makes it possible to significantly save time. Products of this kind are produced by many companies in different countries but there are a few worth noting. They are very popular, ranking first in the ranking of the best.

Gate remotes manufacturers

Several companies can be distinguished among the most popular manufacturers of automation on the modern market:

  1. CAME;
  2. Nice;
  3. Hormann;
  4. BFT;
  5. FAAC.

Any manufacturer uses modern technologies, due to which there may be some similarities in the work of the offered goods, but still more differences.

CAME control panels

An Italian company occupying a leading position in the world market. They produce a variety of automation products that ease the daily chores of a person. Each product is characterized by high quality, the accuracy of the work. Remote controls and locks of the company are affordable and can also be used in any climatic conditions. Performing all installation work requires a minimum set of skills, the main thing is strict adherence to the instructions. Any key fob has distinctive programming characteristics. Before carrying out the work, it is worth studying the instructions attached to the product.

Remote control - Came TOP-432NA model

The most popular model among a huge number of people. Such popularity is due to the fact that it is two-channel, which makes it possible to control a separate device to open a barrier, a gate. The product was manufactured using constant code technology. They are distinguished by small sizes - 32 * 68 * 13. The task can be completed up to 150 meters. Programming takes place in the following sequence:

  1. A working device together with a new one must be located at a distance of about 5 mm from each other.
  2. On a new key fob, you must simultaneously press two buttons, hold them until the indicator starts flashing quickly.
  3. We release both buttons, then press the one that needs to be programmed. In this case, the indicator should light up evenly.
  4. On the old remote control, you need to quickly click the key with which the reinstallation will occur. This manipulation is carried out until the new device starts to glow.
  5. If everything is done correctly, the indicator of the new device will blink three times. If this is not the case, it is worth repeating all over again.

Nice console

Specialization company production automated systems specifically for gates, barriers, doors. The Italian company also holds a leading position in the world market. The products are of high quality, reliability and durability. One device can actually perform several tasks while staying at home.

Keyfob programming for Nice FLO, FLOR automatic gates

The device series is characterized by a rolling code frequency of 433.92 MHz. It is possible to perform manipulations at a distance of up to 150 meters. the dimensions of the products are relatively small. The line is presented in several variations of one-, two-, three-channel models. The programming is carried out according to the following scheme:

  1. First, the receivers are located side by side;
  2. All units must be arranged sequentially
  3. You must hold down one of the keys for about 5 seconds.
  4. The button of the old device must be clicked three times.
  5. Next, you need to press the button of the new device, which was previously held down once.

Hormann key chains for automatic gates

Time-tested German quality. The company's products are of excellent quality as well as attractive designs. The design is made in one direction, the product differs only in different radio frequencies. The differences can also be seen visually. The model equipped with blue keys is characterized by a frequency of 868 MHz, green - 29.975 MHz, gray - 40 MHz.

Hormann HSM 4 keychains

In private use, the model Hormann HSM 4 is very popular. Performs four-channel remote control of gates, barriers. dimensions products 37 * 110 * 13, radio frequency 868 MHz. Has dynamic code.

keychain programming for automatic gates:

  1. First, 2 devices are placed old-new "head to head".
  2. Hold down the key of the old key fob. The indicator should light up constantly.
  3. Hold down the new programming key. At first, the indicator light should flash slowly, and if the programming is successful, it will flash quickly after 4 seconds.

Keychain Doorhan

The largest Russian supplier automatics for gates, radios. Doorhan Transmitter 2, Transmitter 4 - a feature of these key fobs is also dynamic code. They are designed to control two or four automatic devices. They can also be used for any other equipment that is equipped with a company radio. Reprogramming involves performing the following actions:

  1. To reprogram the device, you must first clear the memory of old codes. After turning it on, you need to press the record key and hold it for 10 seconds. If everything worked out correctly, the indicator will blink for 10 seconds, then go out, then blink 2 times. This means that all the old codes have been removed.
  2. To write the required code, you must press and hold the SW1 button on the receiver board itself for 3 seconds. Then it is worth holding the device button for 2-3 seconds.
  3. Such manipulations should be carried out for each key, reflash the control code for a specific device.

Keychains BFT - product features

ВFT Mitto 2-12, ВFT Mitto 4-12 - respectively two- and four-channel remotes. The frequency of the products is 433.92 MHz. Programming the product is quite easy, you just need to perform a few manipulations:

  1. Press the "Ok" button, after which a greeting will appear.
  2. Press the button again and then the "PARAMETER" menu should appear.
  3. Then press the "-" button several times. The "RADIO" menu should appear.
  4. Press the "OK" button again, after that the next section of the menu for adding key fobs to the memory of the radio receiver "AD start" appears.

To encode key fobs, you need to sequentially perform the following manipulations:

  1. Click the "OK" button, the inscription "hidden button" should appear.
  2. Then you need to press two buttons on the key fob that you want to encode.
  3. The inscription “relise” should appear first, and then “desired button”.
  4. Press one key.
  5. "Ok 1" should appear, which indicates that everything went well.
  6. To carry out coding of other key fobs, the work must be repeated according to this scheme.
  7. After completing all the manipulations, you must simultaneously press the plus - minus 2 times.

Faac recognized as the leader in gate remotes

The Italian company Faac is recognized throughout Europe as well as all over the world. Some time ago, the XT2-868 SLH and XT4-868 SLH devices were very popular. The devices are two or four-channel, they worked up to 50 meters. Performance did not degrade with temperature conditions from -20 to +55 degrees. With their help, it is possible to remotely control gates or barriers. The frequency is 868.35 MHz. But they have already been discontinued, they were replaced by new models of the XT series. They differ more modern design, as well as improved performance. Transcoding of remotes can only be carried out if there is a master keyfob, the one that was recorded first, as well as a key fob where the recording will be made.

  1. On the old remote control, press the P1 - P2 buttons simultaneously for two seconds. Only if the LED flashes can you continue programming.
  2. Key fobs must be placed strictly opposite each other.
  3. In this case, the indicator should be on constantly. On the old remote, you need to click a button that should be overwritten.
  4. New remote control programming key. Release only if the indicator blinks 2 times.
  5. The coding was successful.

V modern world there are a variety of devices that allow people to do their jobs more comfortably. A universal key fob will allow, without leaving your home, a car to open a gate or a barrier to exit, it is convenient especially in bad weather conditions, and also to save time. Many manufacturers offer great amount variety of options. This will allow everyone to choose the most suitable option for a particular case.

All work on programming the device can be done independently, but if any difficulties arise, you should contact special service companies or service centers... Experts will help to eliminate all faults, to establish work. Also, you should go to the specialists if the remote control remote control started to work poorly or does not execute programs. You cannot disassemble it yourself, this can lead to more significant damage.

Programming remote controls for gates.Came, Faac, Nice, Dorhan, Profesional, Gant.

The first step is to register the remote control into the receiver on the control board. All manufacturers of gate automation have a different programming algorithm for remote controls, so there is no single recipe. Let's dwell on the main manufacturers of gate automation presented on the Ukrainian market - Professional (GANT), Came, FAAC, Doorhan, Nice.

First of all, a small educational program.

In Came, FAAC, Nice systems, one remote control is written to the drive receiver, and then the required number of other remote controls is copied from it. If you try to record the next remote control into the receiver, the first remote control and all remote controls recorded from it will stop working. If you have lost the old remote control, there is no need to delete it from memory - it will be erased by itself when you write a new one into the receiver. A huge advantage of such systems is convenience - there is no need to open the cover of the electric drive every time if it becomes necessary to record the next remote control. But this system is very vulnerable - I just need to hold your remote control for 10 seconds to steal a signal on my remote control. And this opens the gates to almost everyone who was holding your control panel (or the control panel of your employees). Let's say you decided to restrict access to the parking lot, put up a barrier and gave tenants 20 Came consoles (equal to the number of parking spaces). But after a couple of weeks there is not enough parking space again. Why? Because employees give each other remotes for copying and there are several times more of them than were given out. You can read how to do this below.

What is the way out? Install the system of Professional (GANT, China) or Doorhan (Dorhan, Russia). The main difference between such systems is that the signal of each console is recorded in the receiver individually. The downside is the limitation on the number of consoles recorded in the receiver (depending on the model, from 25 to 128 pcs) and the need to open the drive or receiver cover each time to record the next remote control. But such a system will not allow clones to be multiplied on the sly. Recommended for businesses and car parks with big amount users. You can't have unlimited trust in every single employee-user, can you? An advantage is the fact that the remotes of these manufacturers are also two to three times cheaper than the Italian ones.

How to program the Professional remote

How to program the Came remote

How to program the FAAC remote control

How to program the Doorhan remote control

How to program the NICE remote

How to program the remote Professional 100 UAH

Press the "LEARN" button on the gate operator control unit for 1 second, the "LEARN" LED will light up. Press the button on the key fob, the "LEARN" LED on the control unit will blink and go out. Your keychain has been saved.

If you need to record additional remotes, repeat this operation. It should be noted that a limited number of consoles are recorded in the receiver's memory (depending on the memory capacity of the microcircuit, the number of recorded consoles can be from 25 to 128 pcs).

To remove all key fobs, you must hold down the "LEARN" button for 8 seconds. All keychains will be erased from memory.

How to program Came 25 Euro remote control


It is necessary to press and hold the PROG (CH1) button on the control unit. The LED indicator starts flashing (left figure). Press the required button on the key fob. The LED indicator lights up with a steady light, which indicates the successful programming of the control unit (right figure). Release both buttons. The console is recorded.

Press and hold both buttons on the remote control you want to program (new remote control) (1). The LED indicator on it will start flashing quickly (2). Release the buttons and press the one you want to program (3). The indicator should light up with a steady light. In no more than 10 seconds, bring the master keyfob (programmed remote control) from below and behind to the programmed one (on which the indicator is on) and press once operating button(4). The LED indicator will flash three times (5) and extinguish (6). To program other remote controls, repeat the operation. Thus automatic system can be configured to work with any number of remote control transmitters with the same code.

How to program the FAAC 25 Euro remote control

To record the FAAC remote control into the drive receiver, you must simultaneously press two buttons P1 and P2 on the control panel and release them when the indicator on the remote control blinks (after 1-2 seconds). Then press and hold the button on the receiver board - the indicator on the board should blink.


While the remote control indicator is blinking, you must press the button on the gate control panel that needs to be programmed to control the gate leaf.Before releasing the receiver button, make sure that the diode is on for about 2 seconds (to confirm that the code has been saved). Now we release the button of the remote control and the receiver. The console is recorded.

But if you want to record more than one remote control, do not try to repeat this operation, as the next remote control (new) will be written to the receiver, and the previous one will be deleted. It is necessary to carry out the operation to copy the remote control. See below how to do this.

On the main remote control (recorded in the receiver), press and hold simultaneously the two buttons P1 and P2 and release them when the indicator on the remote control blinks (after 1-2 seconds).


Then place the copied (new) remote opposite the programmed one as shown in the picture above. On the main remote control (while the indicator is blinking), press and hold the button from which you want to rewrite the signal. Now press on the new remote control the button you want to program. The indicator should flash twice to indicate that the code has been saved. Let go of the button and repeat the operation for other proteins. Thus, the automatic system can be configured to work with any number of remote control transmitters with the same code.

How to program the Doorhan remote control

Before starting programming, it is recommended to clear the receiver's memory of the previously recorded remote control codes. To do this, after turning on the power, hold the record button of the remotes pressed for 10 seconds. The LED will blink for 10 seconds, then go out for 2 seconds and blink twice again to confirm that the remote control codes stored in the memory have been erased.

To write the remote control to the receiver, press and hold for 3 seconds the button for recording the remotes on the radio receiver board - the LED1 indicator on the receiver will light up. Then press the required button on the remote control for 2-3 seconds. To set up multiple remotes, repeat the procedure for other remotes.

How to program the NICE remote

NICE remotes are of two types - fixed code (blue body) and rolling code (black body)

The programming of the Nice Flo fixed code keypad is done by setting the two-position dip switches, both in the keypad itself and in the radio channel. Be careful - the variations must match. If you need an additional remote, simply spin up the old pre-programmed Flo remote and set the switches to the same position. These are old-style remotes, which are very rare today.

Let's take a closer look at programming remote controls with dynamic code.

Programming Nice Consoles with Rolling Code

Press the button on the receiver once (delay is less than 1 sec.). Press the button on the remote control for 3-4 seconds, after which the indicator on the receiver will blink 3 times. This means that the remote control has been successfully recognized and written to the receiver. After that, the receiver will be in the programming mode for another 10 seconds, during this time, by
if necessary, you can record several more remotes. After the expiration of the time (10 seconds), the receiver will remember all the remote controls assigned to it and all the buttons on each remote control.

You can also program the remote control remotely using a previously recorded remote control. As a result, the button of the "new" remote control will copy the command from the button of the "old" remote control. ATTENTION! Programming a new remote control from the old one must occur within the range of the receiver

Press the desired button of the new remote control for 5 seconds, then release, Press (without holding down) the button on the old remote control 3 times, On the new remote control, press the same button 1 time and release. The remote control button is recorded and performs the same commands as the old remote control button.

The remotes stored in the receiver's memory, if necessary, can be deleted. To do this, you need to carry out the following operations:
Press and hold the button on the receiver, You need to wait until the LED lights up 1 time, goes out 1 time, and then blinks 3 times, Release the button on the third LED flash.
If all operations are carried out correctly, then after a short pause, the LED on the receiver will blink 5 times.

Unfortunately, programming of remote controls (RCUs) for gates is not always carried out using uniform methods. The programming algorithm may vary and depends on the manufacturer.
First, you need to register the remote control on the receiver control board. Many manufacturers use the copy-copy method. For example, configuring Faac and Nice requires recording one remote control to the receiver. The rest of the remote controls for automatic gates are programmed by copying from the first remote control. Recording subsequent remotes may disable all others. This method is quite convenient because does not require continuous recording of each gate control panel separately ...
However, the safety of such a system should be questioned. Imagine a situation that your gate control panel fell into the hands of another person for some time. An attacker will need no more than a minute to copy the signal to his own. This is the first thing to think about. Thus, it becomes clear that using such a system for organizations and companies is not the best idea. Signal copying will get out of control.
The GANT and Doorhan systems are an alternative. The essence of such systems is the recording of each remote control into the receiver using unique signals. But it is worth noting that such systems have limitations on the number of recorded devices. These systems are considered to be more secure because it is impossible to copy the signal so easily. For businesses, this is the best option.

Do not forget to erase the old data from the receiver before writing new remote controls. As a rule, all records are deleted by holding the button on the receiver for 10-15 seconds.

Now about programming the remotes in more detail.

  • First, press the "Learn" button on the drive control unit.
    In a second, the LED should light up at this inscription;
  • Then, by pressing the button on the key fob, you will see how the LED will blink and go out.

Congratulations, you have saved the signal! If necessary, carry out the same procedure with the rest of the remotes. This microcircuit can record up to 100 remotes, however, its memory is limited. If it is necessary to remove the keyfobs, hold the "Learn" button for no more than 10 seconds.

Came

  • The control unit has a "Prog" button.
  • Hold down the key before the indicator flashes;
  • We hold down two buttons on the new remote control. In this case, the LED will start blinking;
  • Then you should release the keys and press the one that we have to program;
  • After the LED signal, we bring the programmed key fob to the second one and press work key... The indicator should blink 4 times.

Duplicate remote control from Came gate ready.
To record other devices, repeat the action.

Faac

  • To record, you need to hold down the "P1" and "P2" keys. We release them only after the indicator on the key fob lights up;
  • Then the button of the receiver board is clamped until the LED signal appears;
  • In the process of blinking the indicator on the remote control, press the button that will control the gate leaves. After 3 seconds, release the buttons of the receiver and the remote control.

Signal recorded!

In the Faac system, copying is also used, as in the previous Came system.

  • Press the "P1" and "P2" buttons on the programmed key fob.
  • Release the buttons after the LED signal.
  • Both key fobs are located opposite each other.
  • Next, hold down the button of the main key fob, from which the signal will be rewritten. After the code is saved, the indicator will blink 2 times.

For all other devices, the operation will be repeated.

  • Hold the button on the receiver for 3 seconds. The "Led1" indicator will light up, i.e. recording has started;
  • The remote control button is also held for at least 3 seconds.

The rest are programmed in the same way.

Nice

The Nice company works in two directions - key fobs with a dynamic code and with a permanent code. They differ in body color. Blue is permanent, black is dynamic.

"Nice" with fixed code are programmable with 2-range switches. They are present both on the key fob and on the receiver. These older designs are rare these days. To prepare another key fob, the main one, already programmed by the remote control, you need to unscrew and set the switches to exactly the same position. This system implies copying, so let's take a closer look at this procedure.

  • To get started, take into account that both key fobs must be within the radius of the receiver;
  • We hold the desired button of the new remote control for 5 seconds;
  • The main remote control button is pressed 3 times (short presses).

Everything. The signal is programmed.

Universal gate control

Currently, you can buy a special universal programmable remote control that can be adjusted to a maximum of 4 frequencies and is suitable for 4 different automatic gates (sectional, up-and-over or sliding). We do not think it is worth explaining why it is convenient. The cost of such devices is about 700 - 1300 rubles.

Today in the world market there are many manufacturers who are engaged in automation. You need to be able to program it correctly so that the necessary technologies work well and properly.

Now we will look at the remotes from the gate. If you fine-tune them, you will protect yourself from intruders and make your life much more comfortable. Also, you can use the key fob not only to open the gate, but also for other devices. Let's take a look at how to program the gate remote control.

CAME control panels

This company occupies a leading position in the production of universal remotes. They can withstand a variety of climates and are easy to program.

TOP-432NA

The CAME company is considered the highest quality and most reliable today. You can find many good remotes from her. According to consumers, the highest quality model is the TOP-432NA. What is the reason for this? This remote control is two-channel, which allows you to work with several devices at once, namely, it is possible to open several devices at once, for example, a gate and a barrier. Its frequency is 433.92 MHz. This model is capable of working at a fairly long distance - 140 meters. How to program the gate remote control CAME?

  1. At the first stage, it is necessary to bring the remote control close to the gate.
  2. Next, you need to press 2 buttons. We hold them until the indicator light starts blinking.
  3. After that, click on any button, you just need to choose which one will be used for the gate. If the indicator starts to burn steadily and stops blinking, then you did everything right.
  4. We take the old remote control that came with the gate and click on the button to overwrite the code. It should be remembered that everything must be done quickly while the lamp on the CAME remote control is on.
  5. When the indicator on the new remote control blinks several times, dubbing will end. Now you can use it to work with gates.

Four-channel TOP-434NA

This remote is similar to the first model. The only difference is the size and number of fixtures that can be programmed. The frequency remains the same. TOP-434NA - gate remote control. How do I program it?

  1. As in the first case, you need to bring the remote control to the gate and press two keys simultaneously. We are waiting for the LED to light up.
  2. Click on one of the buttons to start recording on it.
  3. Then we press the button on the special remote control to rewrite the code.
  4. After the indicator blinks 3 times, you can start using this remote control. The data was successfully overwritten.

TOP-432EE

Recently a new keychain from the TOP series has appeared - TOP-432EE. It can work with devices that have been programmed with different encodings, such as TAM and TOP. To get started with this remote:

  1. It is necessary to press the key on the new key fob, which you want to use in the future to work with the gate. We wait until blinking appears on the indicator, and release the button.
  2. Repeat clicking on this button.
  3. After the performed actions, you need to quickly bring the old remote control to the TOP-432EE. Press the key on it, which allows you to open the gate. When the LED blinks 3 times, you can start using the device for its intended purpose.

TOP-432EV

This remote control is considered to be an improved version of the previous model. It has a rather small size, which allows you to carry it in your pocket. Also TOP-432EV can contain 4096 code operations. How to program this key fob?

  1. As before, we hold down two keys until you see the light blinking. Then we release them and move on to the next step.
  2. We select the button to which the data will be moved.
  3. We are waiting for a few seconds until the LED lights up constantly.
  4. We bring the new remote control to the bottom of the other remote control and wait for the rewriting to be performed. This usually takes about 10-20 seconds. When the LED blinks 3 times, you can be sure that the recording has completed successfully.

Came twin

Another novelty is a keychain Came twin... It has one feature - code protection. Strangers cannot easily get hold of the code to open your gate. They are also produced in different variations- two and four buttons. Came Twin is capable of working with dynamic code. How to program the gate remote control?

  1. First you need to make sure that this key fob can already be used and that it has a button for receiving a signal.
  2. We bring the remote control as close to the receiver as possible.
  3. Next, we take the old key fob and press the key where the required code is written. We wait until the LED turns on.
  4. After 10 seconds, press the key on the old remote control.
  5. After about 20 seconds, the process of writing the code will end.

Nice firm

Italian Nice company is in the top for the production of automated systems for various equipment. Their products are of sufficient quality and reliability. Of course they have universal remotes that allow you to manage some processes at the same time. How to program the remotes from Nice gate?

Nice FLO and FLOR

Nice key fobs are easy to program. All models in the FLO and FLOR line can operate with rolling code at 433.92 MHz. They can work even if they are at a distance of 140 meters from the desired object. Remotes are produced with one, two or four keys. Let's look at an example of how to program the Nice FLO2R gate remote control.

  1. First you should go to the receiver.
  2. It is necessary to arrange the consoles in sequence.
  3. Next, select the key to write the code and click on it.
  4. After 5 seconds, you can press the button that is used to open the gate on the old remote control.
  5. It remains only to repeat the keystroke on the first remote control. Button programming is complete.

Hormann

This is a German company that focuses on quality. Its products are quite reliable and beautiful. The manufacturer paints different buttons in different colors to determine specific frequencies for them (blue - 868 MHz, green - 26.975 MHz, gray - 40 MHz).

Hormann HSM 4

This model is equipped with four buttons that allow you to control various equipment. Hormann HSM 4 has a frequency of 868 MHz and the ability to use dynamic code. You can also note the rather small size of the key fob. How to program the Hormann HSM 4 gate remote control?

  1. We place the new remote control close to the old one.
  2. After that, it is necessary to press the key from which the reading will be made. We wait until the light comes on.
  3. Next, you need to press the key that you need to use in the future. After 5 seconds, the LED will flash quickly. Code transfer completed.

Hormann HSE2 and HSM

HSE2 has two-channel mode operation, and HSM - two and four-channel modes. It has a small size, which allows it to be hooked onto keys. The first model operates at 868 MHz and the second at 40.680 MHz. To program them:

  1. First you need to place the remotes close to each other.
  2. Take the old keychain and press the key from which you want to read the data.
  3. Next, press the key that you choose to use in the new remote.
  4. It remains only to wait for the blinking of the LED. We release the keys and we can start using this remote control.

Doorhan

Doorhan is a Russian company. It has entered the world market for a long time and supplies high-quality equipment for automation of work with gates and radios.

Doorhan Transmitter 2, Transmitter 4

These models operate with rolling code at 433 MHz. As you may have noticed from the name, key fobs can work with 2 or 4 various devices... How to program the Doorhan gate remote control?

  1. First you need to delete old records. To do this, press the key with which you can record, and wait. After 15 seconds, everything will be deleted.
  2. Next, you need to press the SW1 button (or any other that needs to be programmed) and on the old key fob to write data. We are waiting for a few seconds.
  3. This concludes the recording. You can start using it.

BFT Company

The most common remotes from this company are BFT Mitto 2-12, BFT Mitto 4-12. They are two and four channel respectively. Able to operate at 433.92 MHz. How to program the BFT gate remote control?

  1. To transfer data, press the OK key.
  2. Next, go to the PARAMETER item and press the "-" button a couple of times.
  3. Repeat clicking on OK. After that, you will find yourself in a menu where you can add a device.
  4. Click on the AD start button and click on the required button.
  5. Next, click on the corresponding key in the old keychain and wait for the data to be overwritten.

Faac

This is a fairly popular Italian company. Its products are used in many countries around the world.

Faac XT2-868 SLH and XT4-868 SLH

These models are used to control two or four devices. The XT2-868 SLH and XT4-868 SLH operate at 868 and 35 MHz, respectively. They can also be used in various climatic conditions. How to program the Faac gate remote control?

  1. First, you must simultaneously press the buttons P1 and P2 to program the key fob.
  2. Next, you need to place the remotes together.
  3. As soon as the LED starts to light up, you need to hold down the key on the old device, which will be used in recording.
  4. In the new remote control, select the Slave button. After 15 seconds, recording will end. Then you can start using this remote control.

Conclusion

Today you can program the reviewed remotes for many devices. How to program the gate remote control? As you can see, this is pretty easy to do. In many remotes, the actions are very similar. To make everything go well, follow the instructions. You can choose the remote control of any company which you like best. Of course, you have to find the right frequency. This will important parameter when choosing a remote control.