entranceWhy with the driver. What is the driver and how to install it
The article is more relating to the wired Internet or Wi-Fi, and not a mobile, but will be instructive for everyone. We divide problems with connecting to two types: physical and software. Physical is all connected with the equipment, wires and problems of the provider itself. Software is what depends on windows settings and / or router.
How to check whether the Internet or problem works in another
Sometimes it helps to update the firmware of the device. Especially useful if your router infected the virus. Yes, yes, and so no longer! How to do it, read on the site of your router, everything is very individual. Step by step instructions, even in general terms, I will not give, because I believe that this should be done by a specialist.
If you know how to reconfigure the Internet on the router, I advise first by default. Another faithful feature exclude a router, it is directly connected to a computer to a computer, bypassing the router.
Software problems and their decision
For a number of clear reasons, within the framework of the article, I can help specific recommendations only on this item.
Invalid connection settings
You are connected directly, without a router
It happens that the network connection settings in Windows 7/8/10 are lost. When you hover the mouse on the network icon, you can observe the constant status of the "Identification ..." network. May not be obvious errors. To fix it with the right mouse click on the connection icon and select "Network Management and Common Access Center"
In the screenshot icon Wi-Fi connectionsIf you are connected by a wire, it will be in the form of a computer. Click on connecting, in my case it is "Wireless Network Connection"
Such a window must open, in which you need to click the "Properties" button
Next, you need to enter IP and DNS addresses that the Internet provider gives. Usually, they are spelled out in the contract, but you can call and ask. But, as he was put, there is no need for this and sufficiently put the switches as in the screenshot, i.e. on the automatic receipt Settings:
As one of the frequent problems of solving the problem, will advise to remove the TCP / IP version 6. Reboot. On the video, all this is also.
WiFi without access to the Internet
When using a router, in 99% of cases, it should also be specified that automatically obtaining addresses (see above). To make sure that the network settings are correct on the computer, it is enough to try to go to. Everyone has different devicesBut how to do this in the general case, I showed at the end. Check if the admin part includes, but the Internet does not work, it means that the problems in the WAN network settings on the router.
Also, the right sign of the lack of access to the Internet at the router itself will be such an icon in the system tray:
When you hover over which, "without access to the Internet" will appear. This means that the connection with Wi-Fi router Installed, but the Internet is not connected to it.
Fix it can only know correct settingsthat must be spelled out in the contract with the provider. You can use the automatic definition of parameters. General principles And the example of the router setup is described in the article "", and is suitable for wired connection. All are described in another article.
Damaged TCP / IP and WINSOCK protocol parameters
Without going into technical details, I'll just write what you need to do, and you will repeat. Do it if any of the above did not help you. And it is desirable to restore the system before execution of commands. Then, if something goes wrong, you can roll back.
And the last advice, but no less effective. There is such a thing as a firewall in Windows, it is also called firewall. it software Protects the computer from external threats, for example, from hacker attacks. But, with incorrect or damaged settings, you can block access to the network. So try Windows.
If after that the Internet earn, then you need to reset the firewall settings and then turn it back. If you have antivirus with a firewall function, it is necessary to disconnect it in its settings. This is usually done using click right-click on the anti-virus icon near the watch. Using ESET NOD32:
Reset Anti-Virus Settings is needed through its interface.
And here is the promised video with examples from the article:
We go to the registry editor. For this, no matter what you have windows version - XP, 7, 8 or Windows 10, press the Win keys (with the Windows emblem) + r and in the "Run" window that appears, enter the regedit, then press ENTER.
We have a registry editor. Left - folders - Registry sections. Go to the section . On the left you will see a list of parameters and their values. Note the appinit_dlls parameter and if its value is not empty and the path to any.dll file is registered there, you reset this value by clicking the right mouse button by parameter and selecting context menu "Change the value." Then look at the same parameter in the same registry subsection, but already in HKEY_CURRENT_USER. There should be done the same. After that, reboot your computer and try to open any page when the Internet is connected. In 80% of cases, the problem turns out to be solved.
Malicious programs
It is often the reason that the sites do not open up is the operation of any malicious or potentially unwanted programs. At the same time, given the fact that such programs are often not determined by any antiviruses (after all, they are not a virus in the literal sense of the word), you may not even know about their existence. In this case, you can help special tools to combat such things, the list of which you can find in the article. The situation described in this instruction I would recommend using the last of the utilities specified in the list, in my experience, it shows itself the most efficient. After the removal procedure, restart the computer.Static routes
Go to B. command line And introduce route -f. And press ENTER - this will clean up a list of static routes and can be a solution to the problem (after rebooting the computer). If you need to adjust the routing to it to access local resources of your provider or other purposes, then this process will need to repeat. As a rule, nothing like that does not need.
The first method and all subsequent described methods in video instructions
The video shows the method described above to correct the situation when sites and pages are not open in browsers, as well as those methods described below. True, here in the article tells how to do it all manually, and in the video - automatically, using the AVZ anti-virus utility.
The notorious file hosts
This option is unlikely if you do not open a single page in the browser, but try, however, it is worth it (usually editing hosts is required if classmates and VKontakte sites do not open). We go to the folder C: \\ Windows \\ System32 \\ Drivers \\ etc and open out there hosts file Without any extension. His default content should look like this: # Copyright (C) 1993-1999 Microsoft Corp.
# This is a sample hosts file Used by Microsoft TCP / IP for windows.
# THIS File Contains The Mappings of IP Addresses to Host Names. Each.
# Entry Should Be Kept On An Individual Line. The IP Address Should
# Be Placed in the Corresponding Host Name # Be Placed In The First Column Followed by the CRESPONDING HOST NAME
# The IP Address and The Host Name Should Be Separated by At Least One
# Additionally, Comments (Such As These) May Be Inserted on Individual
# Lines or Following The Machine Name Denoted by A "#" Symbol.
# 102.54.94.97 rhino.acme.com # Source Server
# 38.25.63.10 x.acme.com # x client host
127.0.0.1 Localhost.
DNS failure
If, when you try to open the sites, the browser tells the DNS server does not respond or failure DNS, then it is likely that the problem is in this. What should be done (these are separate actions, after each of them, you can try to go to the desired page):
- In the properties of your Internet connection, try instead of "receiving the DNS servers addresses automatically" to put the following addresses: 8.8.8.8 and 8.8.4.4
- Enter the command line (Win + R, enter CMD, press ENTER) and enter the following command: IPCONFIG / FLUSHDNS
Viruses and left proxies
And one more possible variantwhich, unfortunately, is also often found. Perhaps the malicious program has been made to the properties of your computer's browser (these properties apply to all browsers). Antiviruses do not always save, you can also try special means to remove malicious programs, such as.
Reset TCP IP Protocol
If you have reached this place, but sites still do not open in the browser, try another option - reset the parameters of the TCP IP Windows. To do this, run the command prompt on behalf of the administrator and follow the two commands (enter the text, press ENTER):
- netsh Winsock Reset.
- netsh int ip reset
After that, you may also need to restart the computer.
In most cases, one of the listed methods helps. If you still failed to correct the problem, then first try to remember what software You have installed lately, and could it affect the settings of the Internet parameters on your computer, do you have suspicion of viruses. If these memories did not help, then it may be necessary to call a specialist in configuring computers.
What if there is an Internet, and the browser does not load the pages? There are various reasons for which arises this problem. It absolutely does not matter what device you have, network connection type, type of operation, browser. Attempts to open the site lead to long downloadIn the end, we see a notification of the error. Its text differs depending on the type of web browser, and usually helps to determine this error. The most common is the problem with the DNS address, if not registered in network settings Or incorrectly entered. There are still popular failures - difficulties with a proxy server, Hosts specialties, registry, malicious software.
The Internet is, but the pages are not loaded: what to do?
To begin with, you should try to restart the modem, computer and router. If the cause is the equipment failure, it will help. In the case of DNS problems, you need to make Ping some public DNS Server, for example google. If the connection cannot be found during checking a node, the reason is the inaccessibility of the DNS.
To correct the situation when the page is not loaded, it is recommended to enter data from Google. Need:
- go to network connection;
- find your type of network connection;
- click "Properties";
- enter Google Information: 8.8.8.8.
Then reboot, and everything should start functioning. 
Failures in the registry
If such problems arose, the browser does not load the pages, go to the registry editor and find subsection subsections:
NKY_LOCAL_MACHINE \\ SOFTWARE \\ Microsoft \\ WindowsNT \\ CurrentVersion \\ Windows.
Next, a list of parameters must appear, among which you need to find Applnit_dlls.. It is necessary to see its value if there is not empty, the path to the file with the expansion dLL, you have to reset.
Then similar actions must be performed with a special parameter. HKEY_CURRENT_USER. And make a reboot PC.
The browser cannot connect to the web site if the malware is penetrated, applications, most often not defined by antivirus. In such a situation, it is better to use special tools that allow you to scan computer equipment. These include the junkwareremovaltool utilities, AdwCleaner, as well as Dr.Webcureit and others.
Internet is there, and the browser does not load the pages: setting up the proxy server settings
In this case, it is important to see that there is nothing superfluous in the parameters. To do this, go to the browser properties, click "Setting up the network" in the "Connection" item. Mark must stand on the line " Automatic definition parameters. "
This helps not always, if the Internet does not ship the page, because there are cases when the proxy is set in manual mode.
HOSTS file may not give to open some resources, while portals are loaded correctly.
To solve, go to this path:
c: \\ Windows \\ System32 \\ Drivers \\ ETC \\ HOSTS.
Inside, there is a text that ends with a line 127.0.0.1 Localhost.. If there are some lines with IP addresses that are not prescribed by the user, they must be eliminated and performing a system reboot. If you need, you can delete all the lines. This does not affect the quality of OS work, but can fly part of hacking if this file The prohibitions of updates of some programs were written.
There is an Internet, and the browser does not load the pages? Start with a simple reboot, if it does not help, you can proceed to check other parameters. Good luck!
It is not rare to deal with the problem when after connecting the device to Wi-Fi network Internet does not work. Connection is there, everything seems to be good, and the Internet does not work. Pages in the browser do not open, programs do not see the Internet connection. As a rule, such a problem appears when setting up Wi-Fi Routerbut. But, often there are cases when everything works, access to the Internet is, and at some point he simply disappears. At the same time, the same laptop, a smartphone, or a tablet to Wi-Fi connected, and does not enter the Internet.
I myself often encountered such a problem. There are a lot of reasons and solutions. Therefore, the main thing in everything in order to figure out. Understand who is guilty of this situation and eliminate the problem. It is clear that it is guilty of either a Wi-Fi router (which is all more often), or our device that stopped working the Internet. It can be a computer, laptop, tablet, telephone, etc. No matter. The result is one - there is no connection to the wireless network, but there is no Internet.
What would be clear to divide the article on three points:
- What if the problem is due to the router.
- Solving a problem on a laptop, stationary computer.
- And solving the problem with the Internet on mobile devices (Tablets, Smartphones).
And so, as I already wrote above, we need to find the reason why the Internet on our device does not work. As practice shows, mostly guilty router, Wi-Fi network itself.
If you encountered this problem when setting up the router, then go to the link, and read a separate article with solutions :. Everything is described in detail and shown.
If a problem occurs when Wi-Fi is connected, but the Internet does not work, always first check the router and the Internet connection, as I described it above. Since the reason very rarely lies in the laptops themselves, smartphones, tablets, and other devices.
If the Internet on Wi-Fi does not work because of problems in the router
How to find out and check? Very simple. You most likely have several devices that can be connected to Wi-Fi. We connect them to your network, and if the Internet does not work on any device, then the problem is exactly in the router. Or, you can connect your laptop (smartphone, tablet) To another Wi-Fi network and check the work. After you have convinced that the problem is in the router, you can try to solve it:
- To begin with, simply. You can even several times.
- Be sure to make sure that the Internet is paid, and there are no problems on the side of the provider. What to find out, you can call in support of the Internet provider. Also, you can connect the Internet directly to a computer. (if there is such an opportunity) And check whether it will work without a router.
- Check if the wires are connected to the router correctly. Look at the indicators on the router itself (whether they are flashing as usual).
- If the Internet works without a router, then you need to check the settings. The settings may have fallen, and the router cannot connect to the Internet, establish a connection to the Internet provider. I do not know what kind of router you have, so you look for instructions for your manufacturer on our site, in the "Routher Setup" section (Top View).
- If the Wi-Fi network is not yours, it is quite possible that some problems have appeared in her work. Or, for example, a neighbor did not pay the Internet 🙂
Here is another detailed article on this issue that you will be exactly useful:
Laptop to Wi-Fi is connected, but there is no access to the Internet
If the problem appeared only on a laptop, or a fixed computer, then you need to check some settings. After connecting, you will most likely be a yellow exclamation icon near the connection icon, and the status "Without Internet access", or "Limited".
And when trying to open the site, we will see a mistake "The page is not available".
Our site already has a great article to solve the error. If you have Windows 10, then see the article.
First of all, I would advise you to reboot a laptop, and whether to check whether the automatic receipt of the IP address is set in properties. wireless connection. You can do it like this:
What if Wi-Fi is connected on the phone (tablet), but the Internet does not work?
On mobile devices that work on Android, iOS, or Windows Phone, exactly the same situation. Connecting to a wireless network can be installed, but the pages in the browser will not be opened.
By the way, on Android devices Wi-Fi connection icon can be gray instead of blue. In this case, check whether the date and time is set correctly. If you are sure that the problem is in your device, and not in the Wi-Fi network, then restart your mobile deviceAnd try connecting again. Also, check how the Internet will work when connecting to another wireless networks.
If the tips did not help, then describe your problem in the comments. I will try to advise something.