Menu
Is free
check in
home  /  Navigators / An Operating System Wasn't Found. Try DisconNecting Any Drives That Don't - What to do

An Operating System Wasn't Found. Try DisconNecting Any Drives That Don't - What to do

Sometimes when reinstalling the operating room windows systems either when moving with more new system An error occurs on the old: " An Operating System WASN "T Found. Try Disconnecting Any Drivers That Don" T Contain An Operating System". Also, this error may occur due to not competent interference in the hidden boot section hard disk. In this manual you can learn how to eliminate the error "An Operating System Wasn" T Found. "

In Windows 7, 8 or 10, the system load is carried out with hidden section (Reserved by the system). Each of these operating systems has a hidden partition has a different volume: in Windows 7 - 100 MB, in Windows 8 - 350 MB, in Windows 10 - 500 MB.

When installing the system, you probably could see these sections.


In a hidden section, the operating system boot files are located. If this section is not active for any reason, the operating system will not be loaded accordingly and you will see an error "An Operating System Wasn" T Found. Try Disconnecting Any Drivers That Don "T Contain An Operating System".

To eliminate this problem you just need only make a section active.

The hidden section should always be the main and active. This iron rule, thanks to which the BIOS understands that download files are located on the specified section. Let's see with you that is stored on this hidden section as an experiment. To begin with, enter "Disk Management",

Since I use Windows 7, it can be seen that I was reserved by a system of 100 MB. If you assign the letter to this hidden partition, it will be displayed in the "Computer" window, subject to activated item in the settings of the "Display of hidden protected system files".

As you can see on this disk, the OS bootable files are located.

Below we will consider two ways, thanks to which the error goes and the system will again boot into as usual mode. By the way, all manipulations can be performed both on Windows 7 and on Windows 8 and Windows 10.

Method 1. How to make a section active using Acronis Disk Director

First you need to create a bootable disk Acronis Disk Director.if it is not. The image can be downloaded on the Internet, and then write to the disk. If you do not know how to do it can read the article. Next, load from this media.

The hidden section should always be active as I wrote above, that is, in the program it should be marked with a red checkbox. As can be seen below, the hidden section is inactive,

Correct this - press the right mouse button on the section and click on the item "Mark as Active",

In order for the changes to enter into force, press the button with the "Apply Expected Operations" checkbox.

After performing the operation, you can see that the section has become active.

Now it remains to restart the computer. If everything is done correctly, the system will boot and you will get on your familiar desktop.

Method 2. How to make a section active using the Windows installation disk

If not under the hand of the disk with Acronis Disk Director, then do not despair. You can do without this program, but the installation disk with the operating system will still need. Loading from it by pressing any key on the keyboard,

Two errors on the black screen in the case when Windows 10 does not start - "Boot Failure. Reboot and Select Proper Boot Device or Insert Boot Media in Selected Boot Device and An Operating System Wasn't Found. Try DisconNecting Any Drives That Don't Contain An Operating System. Press Ctrl + Alt + Del to Restart »As a rule, they have the same causes, as well as ways of correction, which will be discussed in the instructions.

In Windows 10, both one and other error may appear (for example, if you delete the bootmgr on LEGACY loading systems, an Operating System Wasn't Found appears, and if you delete the entire loader section - Boot Failure error, Select Proper Boot Device ). Also can come in handy: - All possible reasons and solutions.

Before rebuilding errors in the methods described below, try to execute what is written in the text of the error message, and then restart the computer (press Ctrl + Alt + Del), namely:

  • Disable all drives that do not contain the operating system from the computer. Meaning all flash drives, memory cards, CDs. Here you can add 3G modems and connected by USB phones, They can also affect the system launch.
  • Make sure that the download occurs from the first hard disk or from windows file Boot Manager for UEFI systems. To do this, go to the BIOS and in the boot parameters (boot) look at the order of loading devices. It will be even easier and if when using it, the launch of Windows 10 passed normally, go to the BIOS and change the settings accordingly.

If such simple solutions It does not help, then the reasons that caused the appearance of Boot Failure and An Operating System WASNT FOUND errors are more serious than simply not the loading device, we will try more complex error correction options.

Windows 10 boot fix

As it was already written above, artificially invoke the appearance of the described errors easily, if manually refore the contents of the hidden section "Reserved by the system" or "EFI" with windows loader 10. In natural conditions, the most often happens like this. Therefore, the first thing to try, if Windows 10 writes "Boot Failure. Select Proper Boot Device or Insert Boot Media in Selected Boot Device »or" TRY DISCONNECTION Any Drives That Don't Contain An Operating System. Press Ctrl + Alt + Del to Restart »- restore the operating system bootloader.

Make it simple, the only thing you need is a recovery disc or boot flash drive (disk) with Windows 10 in the same bit that is installed on your computer. At the same time, you can make such a disk or flash drive on any other computer, you can use the instructions :,

What you need to do after that:

Recovery tools will automatically try to find problems with the loader and restore it. In my checks, automatic correction windows startup 10 works simply excellent for many situations (including the formatting of the loaded section) any manual actions will not be required.

If it does not work, and after rebooting, you will encounter the same text of the error on the black screen (while you are sure that the download occurs with the desired device), try to restore the loader manually :.

There is also an option of problems with the loader after the disconnection of one of hard disks From the computer - in cases where the bootloader was on this disk, and the operating system is on the other. In this case possible variant solutions:

  1. In the "beginning" of the disk with the system (i.e., to the system partition), highlight a small section: FAT32 for UEFI download or NTFS for loading Legacy. This can be done, for example, using the free boot image Minitool Bootable Partition Manager.
  2. Restore the bootloader on this section manually using BCDBoot.exe (the instruction for manual bootloader recovery was slightly higher).

Windows 10 download error due to hard disk or SSD problems

If no bootloader recovery steps help correct Boot Failure and An Operating System Wasn't Found errors in Windows 10, you can assume a hard disk problem (including hardware) or lost sections.

If there is reason to believe what happened something from the listed (such grounds can be: in nutrition interruptions, strange noises HDD, appearing and disappearing hard disk), you can try the following:

  • Reconnect hard disk or SSD: Disable SATA and power and power supply from motherboard, disk, reinstall. You can also try other connectors.
  • By booting in the recovery environment, using the command line, check the hard disk on errors.
  • Try reset Windows 10 S. external drive (i.e. from the boot disk or flash drive in recovery mode). Cm. .
  • Try with formatting hard disk.

I hope you will be able to help the first points of instructions - disabling unnecessary drives or bootload recovery. But if not - most often you have to resort precisely to re-installing the operating system.

Mass transition to the tenth windows version He showed a large number of vulnerabilities of this system, which to a lesser extent sinned the legendary seven. It is in 10-ke users most often catch an error "An Operating System Wasn't Found", which is literally translated as "the operating system is not found." For the sake of justice it is worth noting that it appears and with normal system launches on Windows 7 or 8.1.

Causes of "lack of an operating system"

Unfortunately, no one knows a certain cause of occurrence. According to some information, the cause of the Baga lies in contradictions between different sections Winchester disk (HDD, SSD). When it is not possible to extract the desired information or interferes with something stops the loader, also can manifest "An Operating System Wasn't Found. Try DisconNecting Any Drives That Don't Contain An Operating System. Press Ctrl + Alt + Del to Restart. " Also, the reasons can be attributed a banal critical error in Windows.

An Operating System Wasn't Found Error in Windows

No one has canceled technical breakdowns, very often the user cannot even download the BIOS.

What to do in case of error

When the message "Operating system is not found", nothing good to wait. Everything is really very bad. I.e, simple ways There are no solutions. We will have a lot to tinker with the operating system for its recovery, and sometimes it cannot be done - no signs of startup. The only advantage becomes a small probability of the breakdown of the computer itself, it is still a more program problem.

The computer disassembled?

If the computer recently disassembled for technical reasons (the fees, HDDs) were changed or cleaned from dust, then it should be replaced by the reliability of the connections on Winchester (power supply, SATA). Disconnect each loop and re-insert it in the grooves. In rare cases, it is recommended to double-check the integrity of all wires going to the hard disk. We also do not forget the classics - we take a battery of bios.


Windows 10 boot disk

We will need the installation disk of your Windows 7/8/10, or create blood flash drive. Place in BIOS priority (boot tab) download for disk or flash drive. With it, you will need to try to reanimate the OS. For this there is very good functionAnd it is called "Restoring System". It can be found when installing the operating system after one press "Next". Below will be the corresponding item.


Thanks to understandable signs, it will not be difficult to understand. For reliability, try several options, sometimes with the recovery point may not work. Then go to the item where the image image will be used.

Command line

This method helps the top ten. Go to "Restoring", there click on "troubleshooting", and then go to " Extra options". Select the command line. Next, enter the following commands:

  1. Diskpart - wait for loading.
  2. List Volume - the numbered list of your sections will be released with the system.
  3. SELECT VOLUME 1 * - The number means the number of your system disk.
  4. Active.
  5. Assign.
  6. EXIT and restart the computer.

It is possible to perform some other commands. Here is a video instruction, try them if the described above will not help.

Reinstalling OS

It was impossible to avoid this item. If the methods described above are not effective, then the net reinstalling Windows remains. The only option with the largest share of the error solutions "An Operating System Wasn't Found. Try Disconnecting Any Drives. " It is advisable to format the section where you are going to install the OS.

More options

A small probability that it will help you and save from the campaign to service centerBut you still have to try.

  1. Pull all installed drives from PC. No flash drives should be. Disconnect the additional hard drive, mice and other devices.
  2. It is worth considering the option with a breakdown of the connector on motherboard. Check the hard disk on another PC, so it will be possible to establish whether the problem is or something else.
  3. When reinstalling Windows, use the licensed version, but before that, be sure to format the entire hard drive.

This is all options. With small programming experience, do not try to work yourself with the BIOS settings, which are sometimes about in forums. Better trust this case IT specialist.

While Trying To Boot Windows 10, You Receive The Error: An operating System Wasn't Found. Try DisconNecting Any Drives That Don't Contain An Operating System.

Press Ctrl + Alt + Del to Restart

This Error Mostly Occurs After Windows 10 1809 UPGRADE, OR PERFORM System Restore.. And The Most Probable Culprit Behind This Problem Is The Corruption of System Files. If ANYTHING DAMAGES Your Computer's System Files, You May Find YourSelf " Operating System Not Found"While Booting. If You are Also Stroggling From this Problem, Here How to Fix An Operating System Wasn't Found After Restart or System Upgrade.

An Operating System Wasn't Found

First of All, Disconnect All External Devices Include Printer, Scanner, External HDD and Restart Windows. Check Windows Started Normally.

Since This Error Often Occurs When Bios Is Unable to Find The Hard Drive, Checking Bios Settings Might Be a Good Solution.

To Check The Bios Settings, Follow These Steps:

  • Restart The Computer
  • Press The F2 Key To Open The Bios Menu.
  • Check the BIOS 'Main Screen to See Whether It Detects The Hard Drive,
  • Also, Check The Boot Order to See If it is Set Correctly.
  • Verify That The Hard Drive Is The First Boot Device.

If The Hard Drive Is Not Detected Properly, Consider Replacing The Data Cables, Or Resetting The Bios Settings to Default Values.

Here Are The Steps to Reset Bios Settings:

  • ENTER THE BIOS SCREEN BY FOLLOWING THE STES OUTLINED ABOVE
  • Find The "Reset to Default Option.
  • Choose The Ret Option, And Answer "Yes" WHEN PROMPTED FOR A CONFIRMATION
  • THEN, SELECT THE "EXIT -\u003e EXIT SAVING CHANGES" OPTION.

Perform Windows Startup Repair

The Windows Startup Repair May Recover Certain Boot Process Related Errors in Some Cases. Here Are the Steps to Access The Startup Repair from Advanced Options. SINCE DUE TO THIS PROBLEM Windows Unable to Boot Normally, You Need A Windows Installation Media To Perform Next Steps. If You Don't Have Check How to Create From Here.

  • WHEN YOU ARE READY WITH WINDOWS 10 INSTALLATION MEDIA / USB
  • Place the Windows Boot Media on the Computer and Boot from It.
  • At The First Setup Screen, Choose Your Language, Time - Currency and Your Keyboard Input Method and Click Next.
  • NOW ON THE NEXT SCREEN SELECT REPAIR YOUR COMPUTER.

This Will Restart Windows Now Next Click Troubleshoot -\u003e Advanced Options -\u003e Startup Repair.

Wait While Windows Diagnosis and Fix Problems. When The Startup Repair IS Completed This Will Automatically Restart Windows and Try to Boot in Windows Normally.

REPAIR CORRUPTED BOOT FILES

IF Startup Repair Failed to Fix The Problem, Then Follow The Steps Below to Configure and Repair the Boot Files.

  1. AGAIN BOOT From Windows 10 Installation Media
  2. Once You Have Reached The Windows Setup Screen, Press The Shift + F10 Keys to Bring Up the Command Prompt.

NOW FIND OUT WHETHER Your Disk Is Set to Guid Partition Table (GPT) or Master Boot Record (MBR):

IN THE COMMAND PROMPT, TYPE diskpart. and Press Enter.

NOW TYPE lIST DISK. And Hit The Enter Key to Find Out If Your Disk Is Set to Gpt Or MBR Partition.

Look at the GPT Column to See If IT HAS An Asterisk (*).

  1. If You See An Asterisk (*), That Means That Your Disk's Partition Table is GPT.
  2. If You Don't See An Asterisk, That Means That Your Disk's Partition Table Is MBR.

Type Exit and Press Enter.

Now Fallow Below We Have Two Different Solutions for Different Partitions.

Fix Boot Files ON MBR PARTITION TABLE

Note: If You Have GPT Partition Skip Thi and Fallow NEXT STEP

NOW FIND OUT THE DRIVE LETTER WHERE Windows Installed. You can do this by Type Command Type list Volume And Hit The Enter Key. You Will Notice The Drive Letter Where Windows IS Installed As Boot.

WHEN YOU FIND OUT WHICH DRIVE CONTAINS THE Windows Folder, (for me its drive "C:"), Give The Following Command to Create The Boot Files On That Drive and Press Enter.

bCDBOOT C: \\ Windows / S C:

* Note: If Windows Are Located On A Different Drive, Change The Letter C With That Drive Letter.

  • After Execute The Command Again Open Diskpart. Utility by Type Command diskpart. And Hit Enter Key.
  • HERE ON DISK PART UTILITY TYPE lIST DISK. Press Enter Key.
  • SELECT THE DISK Letter by using Command SELECT DISK 0.
  • Type Fallowing Commands One by One As Per Instructed Bellow
  • list Volume
  • sELECT VOLUME 3. (HERE SELECT THE VOLUME NUMBER WHICH CONTAINS THE Windows Operating System)
  • active.

Type eXIT To Close The Diskpart Tool. Thats All Now Remove The Installation Media and Reboot Your Computer.

Fix Boot Files ON GPT Partition Table

If You Have the GPT Partition Table Fallow Bellow.

Type diskpart. AND HIT ENTER TO OPEN THE DISKPART UTILITY AND TYPE BELLOW COMMAND.

One of the most common errors when starting the OS, when after the primary check in BIOS Windows or Linux are not loaded, is a failure with the appearance on the Operating System Not Found string screen. What to do in this case, then will be considered. In principle, the error itself, and the correction method is almost identical to those used to eliminate the failure when a notification of the lost (inaccessible) operating system is issued (Missing Operating System), although it only has the difference that the problem is in no way connected with the effects of viruses and malicious codes, and more refers to the hardware and software part itself computer system. As an example, take the Windows-systems that we have more common.

Failure Operating System Not Found on a laptop or stationary PC: What does this mean?

To delve into the essence of the question, you just need to translate the phrase into Russian. It means that the operating system is not found.

In other words, when you start any computer or laptop, you first check all the "iron" devices in the primary I / O system of the BIOS. After the test indicates that all components work normally, starts uploading the operating system for which boot records are used and the loader itself. The appearance of the line like An Operating System Wasn 'Found is just indicating that for some reason access to them is impossible or they are damaged.

To no less, it concerns both Winchesters and SSD devices, on which all information is recorded, including the operating system. In some cases, it can be assumed that the disk has physical damage or failure has been associated with software errors.

Possible causes of failure (An Operating System Wasn't Found. Try to ...)

But to understand the methods of eliminating such an impartial situation, you must first find out all possible reasons that are able to become the original source of such misfortunes.

It is believed that the most common are the following:

  • discal damage;
  • problems with connected plumes;
  • incorrect loading sequence;
  • incorrectly installed SATA parameter;
  • outdated BIOS firmware;
  • damage to the bootloader and the corresponding records.

As we see, the reasons are the same as when notified is notified of the lost OS. All methods below work to eliminate both failures.

BIOS download and boot settings

So, the user on the monitor screen observes the appearance of an Operating System WASN string "T Found. First of all, you need to make sure that all the BIOS / UEFI primary system settings are set correctly.

One of the most common phenomena can be called a situation where the user simply forgets to remove the removable device from the drive or port, so to speak, non-system type. That is, the files needed to download the OS, as well as the operating system itself, there are no carriers, but they themselves before HDD have a higher boot priority.

The output will be either withdrawing all removable media and disabling removable devices with a subsequent reboot, or the hard disk is set as the first device from which the main operating system will be started (this option is called 1-ST Boot Device.) And put it in the Boot section, in the name of which the words like sequence or priority can sometimes be added. In any case, priority plays one of the most important roles.

Winchester problems

Another point when the Operating System WASN't Found row appears when starting the OS, is associated with the hard disk, the SATA mode is incorrectly installed. By default, all the devices of this type in the BIOS are assigned an AHCI option, but it is necessary only so that you can install the operating system (in IDE mode it is impossible). But if there is installed system AHCI mode can make it possible to extract malfunctions Operating System Not Found.

The output of the current situation will be setting the IDE mode with the preservation of parameters when the (F10 + Y) and the full restart of the computer or laptop.

But the all described relates more to the program part, and at the same time the hard drive in the BIOS is determined, even if it is at echoes any errors. Sometimes the appearance of an Operating System Not Found error may be due to the fact that the hard disk is simply "sprinkled" (failed) or incorrectly connected to the motherboard.

In the first case, it is usually necessary to throw it away, although some experts recommend using, as it is considered a unique utility hDD recovery Regenerator. In the second case, you can simply check the correctness of the Master / Slave plume and connectors. It is possible that the loops themselves may be damaged. They will have to, as it is called in electrical engineering, "call".

Reset BIOS settings and setting fresh firmware

The probability of the appearance of an Operating System Not Found error due to the "club" of the settings of the primary I / O system is sufficiently large, but due to the obsolescence of the firmware, as a rule, it is unlikely, although it is not worth it from the bills.

Elimination of the failure in the first case (even subject to the change in all the above parameters to the correct) can be tried to produce by reset bIOS settings to factory. In any modification, you can find a special line like Reset to Defaults, Load Setup Defaults or something like that, which you need to use.

Outdated firmware, which sometimes can also not recognize individual "iron" components, can be replaced by more fresh. However, this is a separate topic. In addition, the process itself, with ignorance, the essence of the question itself is better not to produce.

Looping loader

Finally, almost in each second case, the appearance of Operating System Not Found failure is the cause of HDD errors or broken sectors, which causes damage to the boot areas and the loader itself.

Such a problem is eliminated with four main teams that are prescribed in command linebut it will be called only when loading an external device (for example, with installation disk, recovery disk or USB analogs). Notice standard remedy The restoration of the system, running from the removable device, usually does not give a proper effect, therefore it is not possible to use it initially.

The command console itself is called a pair keys shift + F10 or from the recovery menu. First you need to check the hard disk on errors, and as an addition to install an attribute automatic correction CHKDSK C: / X / F / R (/ F / R / X, / R / X / F - can be combined as you like, the role does not play).

After that, the lines of recovery loader and the corresponding sectors are entered: bootrec.exe / fixmbr and bootrec.exe / fixboot. You can then try to make a restart, but removable media need to withdraw.

If the Operating System Not Found error appears and after that, in the same command Console. You have to make full rewriting of the loader, which is performed using the BootRec.exe / RebuildBCD combination. In theory, if the hard drive is really all right, the error will disappear.

Conclusion

As a result, it remains to be said that all the above-mentioned error correction methods work (verified in practice). But what kind of way to apply? It all depends only on what is the root cause of the failure. But usually it is either mechanical damage Drive and loops, or incorrect loading sequence, or errors that led to the loader and boot sectors.