home / Installation and configuration/ Http 192.168 1.1 why does not come. What should I do if I can't access the settings of the router? The router's IP address is on a different subnet

Http 192.168 1.1 why does not come. What should I do if I can't access the settings of the router? The router's IP address is on a different subnet

In general, the explanation of the various points of setting up the D-link equipment is not very easy for our editorial staff. One router comes with different modifications, which, in turn, may have completely different firmware. Therefore, there is no universal procedure that would suit absolutely all devices. However, solutions of this manufacturer chosen by many users. Models won especially great love of Russian users. D-Link Dir 615, 300, 320, etc. Of course, in the process of work sometimes incomprehensible situations arise.

Today we will find out why users sometimes cannot enter the router interface using the D-Link Dir 300 as an example. address bar browser address 192.168.0.1 when the management interface does not open. In some cases, it is not possible to log into it, since the standard admin password is not suitable. In order to solve these problems, you can return to the factory settings according to the instructions provided.

Today we will try to solve the problem with entering the router interface when, when entering standard address the following errors appear:

the page does not open;
the page is not available;

Frequent login error Personal Area router and other errors in the general article:.

In any case, the user cannot access the settings of the router, since he simply does not have the ability to enter a username and password.

Reasons for unavailability of D-link router settings

Let's consider the most common cases when the transition to the router settings is impossible. Note that if these tips did not work for you and you still cannot open the settings interface, the problem is most likely due to a hardware problem. Here it is better to take advantage of the warranty on the device, if it is still valid. You should also look at the indicators for your router model. If the data and connection lights are off, our tips are likely not going to help you.

Now you need reset settings according to this instruction - .

Wireless connection

Make sure there is a connection. If the router is set up wireless connection, you can find out about this by the presence of such an icon (do not worry if the icon with the signal level is obscured by an exclamation mark).

Cable connection

If the device is connected with a cable, make sure it is intact. From the side of the router, the cable must be installed in the LAN connector and go to the connector for connecting the computer's network controllers. If there is a connection, the following icon should be displayed:

In addition, do not neglect the peculiarities of obtaining an IP address for your router. In the network connection settings, make sure that IP and DNS address was issued automatically. detailed information on setting up connections is given. Here you should pay attention to checking the specifics of issuing IP addresses if it is impossible to enter the router settings page.

If these instructions did not help to solve the problem with opening the router settings interface, you can try to do this using another Internet browser. You can also try connecting your device to a different computer. This can also be done using a mobile gadget connected via a Wi-Fi interface.

If it is impossible to configure the router, the problem is most likely associated with the physical failure of its nodes.

In general, this address is used to enter the settings on most routers and modems. There are many reasons why the browser does not enter the settings located at this address, in fact, I want to consider the main ones in this article.

And so, let's go ...

Please check the address first, did you copy it correctly? (highlighted in blue slightly below)

1) "Wrong" browser settings

Most often, the problem with the browser occurs if you have enabled turbo mode(this is in the Opera or Yandex browser), or a similar function in other programs.

Also check your computer for viruses, sometimes, the browser can be infected with a virus (or add-on, some kind of bar), which will block access to some pages.

2) The router / modem is turned off

Very often, users try to enter the settings of the router (or modem), and the device itself is turned off. Be sure to check that the bulbs (LEDs) flicker on the case, the device is connected to the mains and power supply.

After that, you can try resetting your router. To do this, find the reset button (usually on the back of the device, next to the power input) - and hold it down with a pen or pencil for 30-40 seconds. After that, turn on the device again - the settings will be returned to the default settings and you can easily enter them. (How to enter the router settings

3) Settings network card

There are a lot of problems due to the fact that the network card is not connected, or does not work. To find out if the network card is connected (and turned on) - you need to go to the network settings: Control Panel Network and Internet Network Connections

For Windows 7, 8, you can quickly get into the settings if you press the Win + R buttons and enter the ncpa.cpl command (then press Enter).

Next, take a close look at the network connection to which your computer is connected. For example, if you have a router and a laptop, then most likely the laptop will be connected via Wi-Fi (wireless connection). Right-click on it and click on (if the wireless connection is displayed with a gray icon, not colored).

By the way, you may not be able to enable the network connection. your system may not have drivers. I recommend that if you have problems with the network, try updating them anyway. For information on how to do this, see this article: "How to update drivers".

Important!

Be sure to check the settings of the network card. It is possible that your settings address is not 192.168.1.1, but different. To do this, go to command line(For Windows 7.8 - press Win + R, and enter CMD command, then press the Enter key).

At the command prompt, enter a simple command: ipconfig and press the Enter key.

After that, you will see many parameters of your network adapters... Pay attention to the line "default gateway" - this is the address, it is possible that you will not have 192.168.1.1.

Attention! Please note that the router settings page in different models different! For example, to configure TRENDnet routers, you need to go to 192.168.10.1, and ZyXEL - 192.168.1.1/ (see the table below).

RouterASUS RT-N10ZyXEL KeeneticD-LINK DIR-615Settings page address 192.168.1.1192.168.1.1192.168.0.1LoginadminadminadminPasswordadmin (or empty field) 1234admin

4) Antiviruses and firewalls

Very often, antiviruses and built-in firewalls (firewalls) can block some Internet connections. In order not to guess, I recommend just disabling them for a while: usually it is enough to right-click on the antivirus icon in the tray (in the corner, next to the clock) and click on exit.

In addition, in Windows system there is a built-in firewall, it can also block access. It is recommended to turn it off for a while.

In Windows 7, 8, its settings are located at: Control Panel, System and Security, Windows Firewall.

5) Checking the hosts file

By the way, an even more detailed article about recovering the hosts file -

Now, probably, even schoolchildren already know that a router is a mini-computer and must be configured before using it. Only with all this, not everyone knows how to enter the settings of the router. And really, how ?! For beginners and housewives, this is a completely "Chinese letter", along with the inscriptions on the Egyptian pyramids! We will help you figure it out! At least the entrance to the router will not seem to you such an abstruse activity for computer geeks. So let's go!

The web interface of the router and what it is eaten with

All settings of a modern Wi-Fi router are collected in one graphical interface called web interface or web configurator. Many users also refer to it as "router site" or "router's personal account".

Although this is wrong, it is not devoid of logic. The fact is that in order to enter the settings of the router, you need to use a regular web browser with which you surf the Internet - Chrome, Opera, Explorer or Firefox. So it turns out that you need to go to the router's website in order to configure it and the sequence of actions in order to enter the router's settings is as simple as 5 kopecks.

192.168.0.1 or 192.168.1.1 - which address should I use ?!

So, great, we already realized that all this is easy and simple, but we have not yet figured out how to enter the router's web interface. To do this, you need to know its IP-address. How do you recognize him ?! Again, nothing complicated! We take this hellish piece of iron in our hands and turn it over! On the back there should be a sticker with a bunch of letters and numbers. There is both a model and serial number and a bunch of that similar nonsense. Among all this riot of information, we need to find the IP address of the device. This is how it will look on the sticker:

Usually, to access the settings of the router, an IP address is used either or. Less common addresses are 192.168.100.1, 192.168.8.1, 10.0.0.1 or some other. The username and password for login are usually indicated next to it. In the example in the picture, this is the login admin and password admin.

On many modern network devices, a text, domain address is used instead of IP. Example - tplinkwifi.net y TP-Link routers, my.keenetic.net y Zyxel Keenetic, router.asus.com for ASUS routers.

No need to be afraid - everything is the same, but in a slightly different form. Everything is used the same way - we launch a web browser (Chrome, Opera, Firefox, IE, etc.) and enter either the IP address of the Wi-Fi router or its URL in the address bar. That's all!

Why can't I enter the router settings

As my experience tells me, very often problems with accessing the web interface begin at the very first stage. And it seems that you are doing everything right, the device is working, the lights are blinking, but for some reason it is not possible to enter the settings of the router. No way, from the word "absolutely". What to do and how to be ?! Let's figure it out!

1. The site of the router does not open

You enter the IP address of the router in the browser, and in response you receive an error "Page not found" or "Unable to access the site."

There are several reasons for this. The most common is simply device glitch- try restarting it and check the entry into the router settings again.

The second most popular reason is banal misspelling the router address... You need to write it in the address bar as it is written on the sticker. That is, 192.168.1.1 or 192.168.0.1. Users, as a rule, begin to blunt in a uniform way, coming up with something of their own. For example, they replace numbers with letters - like this: 192.168.l.l or 192.168.o.l - of course this will not work! The IP-address must consist of numbers, and the system will misunderstand the letters! Sometimes, they manage to forget about the dots in the address - 19216811, or add more parts - 192.168.0.1.1 - this will not work either.

Quite common problems with network card settings on a computer or laptop. The solution is also quite simple. Press the keys Win and R to open the Run window. Enter the open command in the line ncpa.cpl and press the "Enter" key, after which we will see a list of network Windows connections... Click on the one to which the router is connected, right-click and select the "Properties" item:

Then, as shown in the figure - double-click on the line "Internet Protocol version 4 (TCP / IPv4)" to open the third window - the properties of the network connection. There we put a checkmark on the automatic receipt of the IP address and DNS servers... This should be done in most cases, since the DHCP server must be enabled on the router by default and it distributes the IP, which means the computer should pick it up automatically!

If this does not help, try registering the IP statically on the network card. Like this:

This is in case the DHCP server is on network device turned off or not working properly. If you suddenly get the error "Conflict IP-address on the network", write down another address - 192.168.1.3, 192.168.1.4, etc.

In the event that none of the advice listed above helped me, try this. Run the command line and write the command in it:

Ping -t

That is, if the router has an address of 192.168.0.1, then the command will look like this:

Ping 192.168.0.1 -t

Press the "Enter" key to launch the Ping command. Thanks to the "-t" switch, packets will be sent continuously, and not by 4 requests, as is done by default. Then you will need to try in turn to connect the patch cord coming from the computer to all ports of the router in turn.

Here the whole "trick" is that modern routers can reassign LAN ports for different purposes - IPTV, SIP telephony, etc. You will not be able to enter the settings of the router through such a port. That is why it is worth checking the rest of the ports. As a rule, if the device is "alive", then it will respond on one of the ports.

2. Factory default password is not suitable admin admin

This is the most interesting situation. It is usually found either among scattered people who forgets everything, or among those who have not configured their own router or modem, surrendered to a third-party customizer or simply entrusted this process to friends, acquaintances, etc.

And the result in both cases is sad - it is not possible to enter the settings of the router under the factory default password and a login or password error is issued. What to do? Unfortunately, in 999 cases out of a thousand, there is only one solution - to reset the router settings. To do this, it has a special "Reset" button, which can be found on the back of the case, next to the connectors. It looks like this:

Resetting the router settings is usually quite simple - press "Reset" and hold for 8-10 seconds. In doing so, it is best to look at the front panel indicators. As they all light up at once or vice versa - go out, then you need to release the button and wait for the device to boot normally. But ATTENTION!!!- after resetting the settings, your router will be again as if it had just been taken out of the box and unpacked. That is, for normal operation, you will need to configure it again. But both the factory login admin and the password admin will work again!

192.168.1.1 login and password can be found in this article, although if you do not know how to set up your router (home Internet) or you can’t go to the 192.168.1.1/192.168.0.1 router settings page or login / password doesn’t fit? With these or those problems, we will help you figure it out in our article.

What is 192.168.1.1 or 192.168.0.1

The numbers provided are the network address or IP to enter the settings menu of your device, to get into it you need to use a browser. These ip are installed by default on most models from various firms of network routers.

The numbers are entered into the address bar of any browser, after which a window pops up in which you need to enter your username and password. By default, the password and login is the word "admin", after successful input you will see the menu web interface. You can also enter 192 168 1 1 using "admin" from another device with a Wi-Fi receiver. Since protection is not installed on it by default, all you need to do is connect to the network, and already through the browser on the device enter everything that is indicated above.

What to do if 192.168.1.1 won't open (unavailable)?

- Browser problem
One of possible mistakes there may be a problem with the browser if the device detects the connected router. You need to install another browser and repeat the action of entering the menu. If this does not help, you need to check your browser for viruses and unwanted extensions.

- Antivirus / firewall problem
The next error is blocking the network address by the antivirus. It is solved by disabling the firewall (protector against unwanted network traffic) for a while, or by adding the network address to the list of safe sites. Standard windows firewall disabled in the following way: control panel - system and security - firewall - disable defender windows... It should be noted that given error is very rare.

- Problem with wire contacts or wi-fi network
If, when connected to your PC via standard cable, it is not detected, you should carefully check all connections and connection indicators on it. It is also necessary to check the correctness of the Ethernet cable connection, perhaps the input was simply confused. The cable must be plugged into a socket, which is located separately from the others and highlighted in blue. If you are connected when Wi-Fi assistance receiver, then you should check its serviceability, as well as the presence of drivers for its operation.

- Problem with network card
This problem often occurs after installing a new operating system... In order to fix it, you need to install the driver package, which usually comes with system unit... It is also important to check the Internet protocols used. To do this, you need to enter the network parameters, click on "connections by local network», Further properties, and already here check the setting of the checkboxes in front of the protocols version 6 (TCP / IPv6) and 4 (TCP / IPv4). All other variants of a malfunction of the network card are most likely associated with a breakdown or incorrect connection. Ultimately, this may be a malfunction of the device itself, in which it is necessary to contact the service center.

How to find out the login and password for 192.168.1.1?

As mentioned above, the standard password and login is the word "admin". Sometimes it can be a combination of words, where the login is admin and the password is password. Most manufacturers indicate on the back: network address, menu access data that is set by default.

You need to check the layout and the correctness of the data entry, then try to change the browser or device through which you are logging in. If all these actions do not help, then you need to reset the settings to the standard ones. There is a hole in the back of the device, which must be pressed for 10 seconds or more using something thin (a paper clip or a needle). After that, everything will return to the factory settings and it will be possible to enter the menu.

How to set or change the password 192.168.1.1

So, after successfully entering the menu, you need to find the Wireless-security section (wireless mode - protection), here you need to select WPA2-Personal protection and set the password that suits you, saving the changes.

What do you need to do in 192.168.1.1 to configure the Internet?

In the web interface, select the network-wan section, then fill in the fields in this section as follows:

In most cases, the connection type should be left as default, or the settings for your country should be set.
In the column for username and password, enter the data from your contract with the provider.

In chapter " wireless mode»You can set the name of your network, set up protection, find out the number of users connected to this moment... Many of the items that are automatically adjusted can be left as default. Most routers have quick setup- this means that all the parameters that need to be configured will pop up in a special window, you just have to fill them in. You can also use the help of a specialist who will install and configure himself as soon as possible.

An overview of the main reasons why you can't connect to the router interface.

Navigation

Today, wireless Internet connection Wi-Fi is mainly used to access the network, and therefore almost every home has a router that distributes the Internet to many devices. As a rule, its setting is carried out by a wizard who conducts the Internet to the apartment. But sometimes the user himself may need to go to the control panel of the router in order to change the password to Wi-Fi or set other settings.

When entering the settings menu, users may encounter certain problems, namely, with an error connecting to a remote server. In our article, we will analyze the most common reasons the occurrence of this problem and its solution.

Why is the browser not included in the router settings menu?

As a rule, access to the settings of the router is carried out through any web browser (browser), by entering into the address bar IP addresses... However, when entering it, many users see the error “ Failed to connect to remote server". There may be several reasons for its occurrence:

LAN cable or power supply is not properly connected;
Invalid IP-address;
There is no automatic receipt by the computer IP addresses and DNS servers;

In the event that the browser opens the login page for the router settings menu, but when you enter the login and password, no changes are made, then the problem lies in the incorrect input of user data. Let's consider everything in order.

Connecting the router to a computer for configuration

Obviously, before configuring the router, you need to connect it to the computer using the LAN cable that comes with it. In the event that you do not do this and immediately try to connect via Wi-Fi, you will fail. To connect correctly, follow these steps:

Step 1.

Plug the router into a power outlet and connect it and the computer LAN cable, which can be found in the box from the router.
Some routers have connectors of different colors, and some are numbered. The cable for connecting the router and the computer must be plugged into yellow connector, or into the connector under the number 0 .

Step 2.

After connecting, the Internet connection lamp marked with a globe should light up on the router.
At the same time, the computer should let you know that a new device has been connected and an Internet connection icon should appear on the taskbar.

Step 3.

Do not be alarmed if the status of your internet connection is “ Without internet access". The thing is that you haven't really configured anything yet.
Try to open your browser and type in the address bar IP address 192.168.1.2. If there is no effect, skip to the next section of our article.

Checking the IP address for connecting the router

On each router, regardless of manufacturer, with back side there is a special sticker on which it is indicated IP address and data for entering the settings menu (login with password).

Flip your router over and take a close look at the contents of the sticker. It is likely that to access the router settings panel you use IP address 192.168.0.1. If so, then rewrite it with precision in the address bar, remembering to put a period at the end.

Configuring automatic acquisition of IP addresses and DNS servers

One of the main reasons why the browser denies you access to the remote server is the lack of settings automatic receipt IP addresses and DNS servers... The fact is that if you previously used another provider or connected to someone else's Wi-Fi, your settings might have saved a static (unchanged) IP address and DNS server.

Many providers today provide their customers with dynamic IP addresses, which change every few days or when the router is rebooted. To set up automatic retrieval IP addresses and DNS servers you need to take a few simple steps: