the main / Multimedia / Enter the router settings d link. How can I enter the configuration settings of the D-Link router

Entering the router settings d link. How can I enter the configuration settings of the D-Link router

Link WiFi routers have gained fast and well-deserved popularity among users global network and in this regard, the question often arises: "How to set up a D Link router?" The following instruction, which is not tied to any of the many Internet providers currently providing communication services, will help most of the owners of Link branded routers. Setting up a D Link router will not cause problems even for novice users if there is an available instruction that describes in detail all the actions of the owner of the device step by step.

Preparing the equipment for the setup procedure

Take the device and all its accompanying components out of the package. Attach the antenna to the body of the router (for some models it is screwed). Connect the cable of the Internet provider to the router connector marked "Internet", and with the patch cord connect the network card of the PC with the Link device by inserting the plug into the connector marked "LAN".

Insert the power supply cable into the power supply socket of the device and connect to the mains.

After that, it is necessary to perform preliminary settings in the PC. This requires the following sequence of steps:

Open the "Control Panel" through "Start";
Go to "Network and Internet";
Then enter the "Network and Public Access Center";
Click on “Change parameters. adapter ";
Select "Local network connection" and open the context menu;
Click on the line "Properties";
Click on "Protocol 4 (TCP / IPv4)" and check the boxes for "Obtain IP automatically" and "Obtain DNS address automatically":
Click Ok.

In case of having already used WiFi router it is recommended to do a factory reset before starting to work with it. The back panel of the device has a special button labeled "Reset".

It is necessary to arm yourself with a thin and sharp object, for example, a straightened wire paper clip, press this key recessed into the body of the device and hold it for several seconds. Wait until the device is fully loaded, usually this process does not take more than a couple of minutes.

How to enter router settings?

The algorithm of actions consists of several stages:

Setting procedure

It is required to follow the following step-by-step instructions:

Menu network devices d-link allows the user to change great amount various information, one way or another related to the used router or modem. Mostly for effective work the network device uses only one configuration principle. If desired, the user can change standard values... For example, you can change the protection method, change the password for entering the network, username, network name, etc. It is worth noting that it is best not to go into the settings of the network device and change nothing there if you are not sure that you will do everything correctly. Even if some mistake was made, the user can reset all settings to factory settings (using the Reset button) and only then, do everything as it should.

How to access the d-link menu?

In order to enter the d-link menu (web interface), you need to open any convenient browser (preferably, when changing the standard settings, use Internet Explorer). In the address bar, you must enter the address of the main network gateway (IP address) 192.168.0.1 or 192.168.1.1. It must be said that this address may have a different form. It directly depends on the manufacturer of the network device and its model. After a small window appears, the user will need to enter a username and password. Sometimes manufacturers of such devices write the factory login and password required to enter the web interface on the box itself. If it is not there, then you can try to write the standard values: login - admin, password - admin (or leave the field blank). According to the standard, these values \u200b\u200bare suitable for most devices of this kind.

If the entered login and password values \u200b\u200bwere correct, then the user will automatically gain access to the settings (web interface) of his network device. Otherwise (if the login failed), this can only mean one thing - the master who connected the Internet changed the login and password to enter the d-link menu. Usually, in such cases, he had to leave a sheet with changed data, but sometimes they do not do this, for security reasons (so that the user does not go into the web interface and, for example, spoil the equipment). If there is no such information, then you can either call this master (if he left contact number) or reset the settings to factory settings using the Reset button (usually located on the back of the router or modem) and try again to enter the d-link menu.

There are a lot of configuration instructions in the media, but they all relate to direct control of the router. To many users in the proposed material, no one explains how to enter, therefore the purpose of this article will be an explanation with step by step instructionsThere is nothing complicated about this, any user can independently, by repeating the recommended steps, connect and configure the router in a few minutes. Also, from this article, the reader will learn about all sorts of problems that can be encountered in the work, and their solution on the spot.

Input data

To connect, you will need the router itself, a patchcord (eight-core twisted-pair cable, crimped on both sides with RG-45 clips, which should be included in the kit for the wireless access point) and personal Computer (or laptop).

As an example, TP-Link will be produced, since most users have it on the domestic market. In fact, there is not much difference between the manufacturers, the differences can only be in the address of the access point itself, in the login and password. By the way, to find them out, you need to turn the device over and familiarize yourself with the information written on the basis of the router (IP-address, login, password). In most cases, the IP-adress is 192.168.0.1 (possibly 192.168.1.1), and the login and password are admin.

Physical connection

The router (modem) must be connected to a power source and make sure that it is in working order (at least one light on the indicator panel is on). One end of the patchcord must be connected to the computer's network card, and the other end of the cable to the router connector. In the device, it is customary to distinguish between network inputs and outputs (they often have different colors). Only one input to connect to the Internet must be signed by the WAN or differ from the rest of the ports (signed by the LAN) in color. The connection to the computer should be carried out only to the LAN interface (anyone, let it be LAN 1, so as not to get confused).

When two devices are connected, the LED on the router's information panel will light up, which will inform the owner that the connection has occurred. The computer screen will also display information that it has been successfully added to local area network... At this stage, the configuration of the router in the WEB-interface mode became available to the user.

Management and configuration interface

Before entering the router settings, you need to decide on the WEB interface that will be used. The manufacturer recommends using a standard internet browser Explorer, however, it does not always display the control panel correctly, so you should take a closer look at alternative programs: Mozilla Firefox, Opera Google Chrome.

Having opened the browser, you need to enter in its address bar IP-addrees, which is indicated on the label at the base of the router (192.168.0.1 or 192.168.1.1) and press "go" (or Enter on the keyboard). In the menu that appears, you must enter your login and password, which are also written on the bottom of the router (most likely admin) and press the "Login" button (or Enter on the keyboard). Successful authorization will present the user with the router's control panel.

Limitations in computer settings

Setting up a router (modem) is impossible if the computer's network adapter does not work in automatic mode... This may be indicated by a warning indicator in the tray (in the lower right part of the screen, near the clock). It looks like exclamation mark in yellow or In such cases, it is recommended to take a pen, sheet of paper and perform the following actions on the computer:

Move to the warning icon and right-click on it. In the menu that appears, select "Control Center".
In the window that opens, on the left side face, select "Change adapter parameters".
From the options offered, select the desired icon (more often it is signed as Ethernet and has a warning logo). Click on it with the right mouse button.
Select "Properties". In the dialog box, find and place the cursor on the inscription "TCP / IPv4". Click "Properties" again.
Copy all the manually written settings onto a sheet of paper (5 lines).
Set the flag opposite the "Receive automatically" menu in both fields. Click the "OK" button, and close all open tabs.

Fighting the network adapter

Customization tP-Link router on a computer is impossible if the computer does not have drivers for network adapter... This is quite possible after reinstallation operating system (then the "Control Center" simply won't have the right icon). Naturally, you need to go to the official website of the manufacturer motherboard (or laptop) and download the appropriate software.

It is possible that the search for the inscription "TCP / IPv4" will not be crowned with success - in the list, except for "TCP / IPv6", the user will not find what he is looking for. To do this, there is a button "Install" in the same dialog box. It is necessary to select "Protocol" and from the offered options indicate the desired interface "TCP / IPv4". If none of the options for configuring the network adapter helped, it's time to contact the IT specialists who will certainly solve the user's problem.

Provider restrictions in the router settings

Many providers provide users with their own routers to work with their networks. Very often, company administrators set their own passwords to access the device control panel. There are not many options in such cases: get access data from the provider (rarely anyone can do this) or do full reset (to factory settings) of the device. The second option assumes that the configuration of the router (password and login, in the factory version must be known to the owner) will depend on the user. Accordingly, before resetting, you need full control of the situation, because very often the provider does not use to connect standard settings (PPTP, VPN, PPPoE and the like). All information for connection should be in the hands of the user.

Wireless connection to router

If the user, before entering the router settings, discovers the absence of the patchcord interface cable, or the corresponding connector is not found in the laptop, do not despair. Most devices support wireless access point control via Wi-Fi. To do this, you need to establish a connection between the two devices. Then open the browser and repeat the steps by entering the access point address.

In cases where access to Wifi router does not require authorization, experts recommend setting a password for use wireless networkotherwise, any intruder who is in the router's coverage area can not only reconfigure the access point for himself, but also harm all user's devices.

Remote connection to the router

It's one thing when setting up a router D-Link DIR or TP-Link - inexpensive devices are limited by the WEB interface, and users cannot get access in any other way. Owners of routers ASUS, LinkSYS, Cisco, Zuxel and other business class representatives can use remote connection to the device or via a COM-USB interface cable. Management using the "console" snap-in is more convenient because it can reconfigure the router for the owner's needs in a few seconds (for this, special scripts are created, which are sent to the router).

The connection is quite simple: using the Putty or Telnet program, the user gets access by the IP address (of course, by entering the password and login during authorization). Then everything happens at the level of commands, which can be found in full not only in the instructions for the router, but also on the manufacturer's official website in the section: “Administration: step by step setup router ".

Finally

The reader will agree that it is easy to enter the settings of the wireless access point, the main thing is that both devices (router and personal computer) do not have manual settings. Any connection problem will indicate that someone has corrected the operation of the network equipment. Having figured out how to enter the router settings, any user can easily connect to a wireless access point and get full control device.

The main thing that the owner of the router should know is that no matter what settings he makes, it is impossible to harm the router and the personal computer at the physical level. The maximum to be feared is reinstall Windows or reset the access point to factory settings. Accordingly, within this framework, you can safely learn all the subtleties in the settings of the router for yourself.

With the comprehensive penetration of the Internet into every home, the number of network devices, including routers, is increasing. The D-Link series is also expanding with new models. With such a variety, it is sometimes very difficult to figure out how to configure it correctly, go into the settings of the D-Link router and what better parameters use. Throughout this article, we will look at a couple simple ways entrance to admin panel routers from D-Link.

A bit of theory

The latest models of devices, when first turned on, immediately activate the so-called basic wireless network. It allows you to conveniently configure the primary parameters without the use of cables. Older versions or revisions require the mandatory use of a wire for initial setup, which is usually supplied in the kit.

Video instruction for setting up D-Link routers:

Before entering the settings of the D-Link router, we need: a personal computer with a network card and a Wi-Fi module, network cable and the router itself.

Cable connection

Usually rear panel D-Link products have several LAN ports and one for the Internet. LAN ports are most often marked in blue and numbered. And the port for the cable from the provider has a corresponding inscription, for example, internet. Less commonly, it can be referred to as WAN. It should be noted that in some new models one of the LAN ports can play the role of WAN.

So, the cable from the provider should be inserted into the port with the inscription Internet, and the short cable coming with the router into any of the LAN ports. Its second end is connected to the network card of the computer. The fact that a connection has appeared between the two devices will be notified by the LEDs on the network card and on the front of the router.

Wi-Fi connection

You can also use Wi-Fi to enter the router. As a rule, the default network starts automatically and has a “self-explanatory” name, for example, it may reflect the model name - “DIR 300”. After opening the list of available wireless networks on your computer, you need to select the one that matches the model of your D-Link device.

It is worth noting that in some models the network may be open, that is, you can enter the settings without a password. But if, nevertheless, it turned out to be closed, then it is worth turning the device over and on the bottom panel, the sticker should indicate the default network name, as well as the password for entering.

Login to admin panel

Almost all settings are made using any browser available on your computer. But for this we need to find out the IP address of our device. Therefore, you need to turn the router over again and on the same sticker or next to it, the default address will be indicated. It will also contain the values \u200b\u200bof the login and password fields set by the developers to enter the router menu.

The specified address must be entered directly into the address bar of the browser. For D-Link products, the address is 192.168.0.1. After pressing the Enter key, the system will ask you to enter your username and password. You need to enter data from the bottom of the device. Typically, the default is a combination of admin and admin in both fields. After pressing the Enter key, you will find yourself in the web interface of the router.

I must say that after logging into the router, you should change the default password to your own, more secure and reliable one. On many modern firmwares, the system itself will offer to do this. To do this, go to the "System" tab, then select "Administrator password", and enter a new value in the fields.

Possible connection problems

Sometimes it is not immediately possible to get into the settings of the router. Possible reasons there may be several:

IP address for network card can be set manually in the operating system settings. It is worth checking this parameter in the network control panel and switching it to the "obtain an IP address automatically" mode;
before entering the default IP address, make sure that it is really equal to the one indicated on the bottom of the device;
often the browser does not enter the settings due to an incorrectly crimped cable. Therefore, it is recommended to use the special one supplied with the router. As mentioned earlier, the main indicator of the network connection at the first stage will be the blinking LEDs of the network card and the lights on the router.

Video of additional problems with connecting the router:

Conclusion

As you can see from the article, setting up your home networking equipment to get a wireless network is not that difficult. The main thing is to clearly follow the instructions, and then everyone can cope with the connection.

Today we will talk about how to enter the settings of the router. Sometimes you need to enter the settings, but many forget how to do this after connecting and configuring the router. In this article I will show you how to log into different models. If you know how to enter the settings of your router but cannot do it, here is an article that describes. This article assumes that your router is already connected to the computer (if the router is not connected to the computer, read the article ""). Let's get down to the instructions.

General entry instructions.

The settings are entered using any browser. You need to drive the address of the router into the address bar and enter the username and password.

First, let's figure out where to get the address of the router. On many models, the address is written on the bottom of the label, as well as the login and password.

If you do not have a label or do not have access to it, then you can also look at the settings of the network card.

On Windows XP here \u003e\u003e

On Windows 7 here \u003e\u003e

You can find out more about how to determine the address of the router.

Having determined the address of your router, enter the address into the address bar in the browser and press "Enter". The Authorization window will appear in front of you, it will ask for a Login (Username) and Password. On many models, the following settings are set by default: Login- admin, password-admin. Also, take a close look at the authorization window, they sometimes write the default login and password, for example, the Zyxel company (below I will show how it looks). After entering the data, click "Enter" and go to the settings of your router.

Let's apply this scheme to some models. The main thing that you must understand is that we will further consider the case when the router is already connected and it has standard login settings. If this is not the case, then the scheme is simple: we determine the address of the router, if we changed the password and login, we remember and enter. Also, if you are unable to remember the changes, reset to standard settings (how to do this is described in the article "How to connect a router"), and then simply reconfigure it.

Login to d link dir 300 router

This login method is also suitable for models d link dir 615, d link dir 320, d link dir 620. Enter 192.168.0.1 in the address bar of the browser (you can enter the settings of the d link dsl 2640u router at 192.168.1.1). In the window that appears, enter the Login and password. If the window view matches the picture below, enter only the login-admin, leave the password blank. :

Then click on the button. That's it, the entrance is complete.

If, after entering the address, any of these windows opens in front of you:

in this case Username is admin, password is admin. Click on the "Login" button. And you will immediately be taken to the Dlink configuration interface. If you are interested in configuring the Dlink router, then on the left side of the page in the menu, select the d link heading. In it you will find a description of how to configure any model of Dlink companies

We use this method for asus rt n10

This option is also suitable for asus routers rt n12, asus rt g32, asus rt n10p, asus dsl n10. We open the browser and in address bar we enter 192.168.1.1. The name, as well as on other routers, by default is admin, the password is the same. See the picture below:

After all the fields are filled in, click the "Submit" button. And you will be taken to the router settings. By choosing aSUS heading in the left column, you will find a description of the settings for various models of Asus companies.

Also, just log into the router tp link tl wr741nd

Also will fit tp link tl wr841nd, tp link tl wr740n. Let's carry out the same actions as described above. Let's open the browser and enter 192.168.0.1. In the authorization window, we will indicate the Login and password admin and admin.

Outcome

This scheme for entering the settings of the router is suitable for all models, the most important thing is to find out the login and password that you specified when setting up the router. If you haven't changed anything, then everything remains standard. Also on our website you will find many instructions and settings. different models routers.