Connecting a computer to the Internet via WiFi Router. How to connect an ordinary computer (PC) to Wi-Fi network? In the process we will need

It often happens that the Wi-Fi operation range is not enough. Users find strange solutions - buying a more powerful router or placing weak somewhere under the ceiling, but it does not always help if only we are talking about Cisco or ZyXEL equipment. To solve this problem, this article has been created that will tell how to connect a router to the router through the cable to significantly increase Wi-Fi coating zone for easy use.

Preparation for work

To create a network where a wired router is applied, it is recommended to use the same devices, and it is not only the compatibility of available technologies. Setting and connecting identical routers is very convenient. Those who wish to save on the purchase of experts recommend purchasing a router and the cheapest access point without the possibility of routing, because the task is the latter - relay the signal.

The Router Router network is possible in two versions - on a wired and wireless channel. Naturally, the connection over the cable is not only more reliable, but also allows you to significantly expand the range of coating, up to 100 meters. The wireless channel is limited to the power and wall overlap - no more than 10 meters for a high-quality signal. Therefore, to organize the connection, you will need a "twisted pair" cable, compressed from two sides by the connector of the required length.

No extrany knowledge

Very often even advanced users have a number of problems associated with setting network device. The whole problem is due to inconsistencies between router manufacturers. Therefore, many IT professionals recommend to study the instructions for use in front of any equipment settings. Hoping on the setup wizard, which will help make changes to the router, should not, sometimes the information is not enough to correctly run the equipment to work.

Before TP-Link or D-Link to a computer or laptop to configure, it is recommended to first file power on them and wait for the full load (20-45 seconds), otherwise, as it often happens, the equipment may not notice that what is connected to it -To device in the LAN port.

Organization of access to settings

Learning: "How to connect a router to a router through a cable?" - Many users may encounter a problem when connecting to a router to make changes from a computer or laptop. Regardless operating system Or equipment manufacturer exists only one requirement - to configure the connected devices must be located on the same network. Solution options are only two:

1. In the factory setting, the router has included DHCP server. An ideal option for all users, requiring only to give the computer to the computer to receive an IP address automatically.
2. But the DHCP disabled server in some models of routers will force the user to work their hands and head. There is nothing complicated in this, but detailed instructions How to carry out an authorized entrance to the router does not prevent.

Setting a dynamic address computer

In the case of the DHCP server on the router and the inability to enter the access point settings, you need to give a computer to receive a dynamic network address. To do this, you need to perform the following algorithm for a PC:

1. "Control Panel" - "Center of Main Network Management". In some systems, this sequence of actions includes the "Network and Internet" item.
2. "Change adapter settings".
3. Press the alternative mouse button on active connected and choose "Properties".
4. Find a line containing TCP / IPv4 characters and click "Properties".
5. Install the checkboxes in two fields opposite the strings "Get automatically". Save and exit.

Before changing the settings in the fifth point, it is recommended to save the set values \u200b\u200bin a notepad or take a screen shot - maybe there are settings for the Internet to work, which you want to restore after two routers are configured.

Task Static Computer for connecting to a router

The router for the house may have disabled so you have to explore the instruction that comes with the device and find the IP address of the router. For example, the address found is 100.333.24.15, and the mask is 255.255.248.0. The user must register on the network setup computer. The difference should only be in the last digit of the IP address, instead of 15 set 16, for example. After performing the actions algorithm described in the previous chapter, the settings are made manually on the fifth point.

1. Install checkboxes in front of the strings "Use".
2. IP address 100.333.24.16.
3. Mask 255.255.248.0.
4. Gateway 100.333.24.15.
5. Preferred DNS 100.333.24.15.
6. Alternative DNS can be left blank.
7. Save and exit.

Physical connection

Before connecting the router to the Internet, you need to decide which device will be a router, and what a repeater. Connects by one connector to the LAN port of the router, and the second connector to the WAN (internet) of the repeater. For ease of configuration, both devices must stand next to each other, be included in the electrical network and reset to factory settings, unless the router is configured to work the provider.

Very often, administrators from the provider when configuring the router protect their own password settings. There is nothing terrible in this, the main thing is that through the LAN port on the router, the Internet has been filed freely, otherwise it is no complete reset.

Related settings

Having understood how to connect the router to the router through the cable at the physical level, you need to produce thin setting Software. A DHCP server must be enabled on the router - this is a setting that automatically assigns the network address to a new device when connected. If a laptop or smartphone is connected to the router, it means that the IP address distribution server works. Otherwise, you need to go to the Find menu and open a bookmark with the inscription DHCP and check the box opposite the inscription "Enable". At the end of the setting, restart the router.

But the repeater in any case requires user intervention. You need to go to its settings and find the tab "Network". Once in the WAN menu, you need to select the connection type "Dynamic IP address". After that, you can begin configuring the Wi-Fi network.

Another option with a wired interface

Actual this option Only in cases where Wan (Internet) log in to the router on one of the devices in non-working condition. Then the cable connection is carried out between the LAN ports of two routers. The problem of such a connection is that two devices with the same network address will appear on the network, which will conflict with each other. Therefore, you need to disable the DHCP server on the repeater when entering the router menu. After that, without leaving the settings, you need to find the LAN tab and set the static address of the relay in the same range in which the router works, but with honors in the end figures. Many specialists recommend a subnet to increase compounds with 250 devices to 500, but the home router is unlikely to drop more than ten connections.

Example for configuring routers

In addition, the cable so that the user it is easier to understand how to configure, we suggest familiarizing yourself with the example.

Settings for a router that is connected directly to the Internet:

1. IP address 192.168.1.1.
2. Network mask 255.255.255.0.
3. DHCP server "Enable".
4. SSID - Glavnaya.
5. Wireless Channel \u003d 12.
6. Cipher Type Aes.
7. PSK / EAP -PPSK.

Settings for the repeater:

1. IP address 192.168.1.254.
2. Network mask 255.255.255.0.
3. DHCP server "Turn off".
4. SSID - RETRANSLATOR.
5. Wireless Channel \u003d 1.
6. Wireless Security Mode - WPA2.
7. Cipher Type Aes.
8. PSK / EAP - PSK.

In these settings, different broadcast channels. This is done so that the access points do not interfere with each other. Such settings will be useful to users who need the Internet in various places of the organized network, for example in different rooms. In the process of movement mobile device It will be automatically switched between routers, and this will not be noticeably affected at the Internet.

TP-LINK to help

But the owners of TP-Link routers were very lucky, because the manufacturer bothered about the final consumer and supplied all his devices for expanding the coverage zone with WDS. It remains only to explain how to connect the TP-LINK router to a similar Wi-Fi device. On the repeater, you must go to the "Wireless Mode" settings menu and find the "Enable WDS" item in the list of proposed settings. Next can be introduced SSID name The router or use the "Search" button, if the exact name of the router is unknown. The repeater will find all Wi-Fi devices within a radius and provide full list with names, MAC addresses and encryption type. It will only be left to select the desired router and click the Connect button. Connection will automatically transfer the user to where it is prompted to register the name of the access point when detecting, as well as set the password and encryption type.

Finally

As can be seen from the review, the Router Router network is not so simple, as it seems at first glance. There are a lot of settings and all kinds of pitfalls that can prepare a network equipment manufacturer or provider. In any case, before organizing a wireless network of the house or at work it is worth starting to perform the task with reading all instructions. Understanding the material part and the principle of devices will greatly simplify the setting of any user, and this article only helps determine the connection type.

It is not necessary to neglect the cable connection, because this class of transferring data for reliability, durability and compatibility with other equipment is significantly higher than wireless interface. Yes, and the Wi-Fi data rate is still behind Ethernet.

According to my observations, few of those who were independently to plug wiFi router , if there wired Internet, knew how to make it right. That is, configure with it with a wireless network and combine into it different devices. As a result, subsequently faced with difficulties that could be solved still at the design stage of the local network.

How to connect wifi router?

Before proceeding to step by step description By connecting Wi-Fi Router, I want to emphasize your attention on one moment.

To create a full-fledged local wireless network, you need to buy just such a device as a router, or it is also called the router.

The fact is that there are a lot of similar type and functionality of devices for various purposes. For example, by ignorance it is easy to confuse with a wired router without WiFi, which also brends the Internet signal over devices. But only with cables - he has no antenna.

Another device similar to appearance - access point. She is generally a bit different from our task. The characteristic difference between the router from the access point is the presence of several outlets for network cables. While the point is usually one.

The meaning of the router's connection is that it is now that, and not your PC, will be connected to the Internet through the cable. To do this, all the necessary parameters required to connect to the provider, which were in one time applied to your desktop, will now be spelled out in the router settings. And all other devices will already receive Internet via WiFi from it from him and according to the rules that will be specified in it.

For clarity, look at the scheme:

In order to connect the home router and configure the Wi-Fi network, I used with a dozen models from absolutely different manufacturers. I can say with confidence that in terms of the configuration of the WiFi router and connecting to the provider the difference between them consists only in the details of the graphic design of the administrator panel. Therefore, overlooking the principle of one model once, you can apply them to others. Today, as an example, I will illustrate the screenshots with two routers - TrendNet TEW-632BR and ASUS WL-520GC.

How to connect a router to the Internet via DHCP?

The first setting that we will analyze is the configuration of the DHCP server.
If a previously computer There was one and he received an IP address from the provider, then we could pick up a lot of computers and gadgets to the router. And this means that it is the router instead of a computer will "communicate" with the equipment of the provider. And already within our home network between these devices, it will assign an internal IP address to each computer, laptop, telephone, TV and everything else.

Procedure:

1. After connecting to the power supply, first of all you need to configure the router to connect to the computer. To do this, insert the internet cable into the WAN slot on the device. And the other cable, with two plugs, which most likely attached to the device, connect one end to the computer network card. There, where there used to be an online cable. Another is in any of the LAN1, LAN2, LAN3 or LAN4 router slots.

   

   I also want to notice that connecting the router to the network is better through the source uninterrupted power. I had an unpleasant experience when good device Netgear came across due to the voltage jump in the network. It just began to broadcast wifi not at 100, and 2 meters. Of course, I had to buy a new one.

   

2. Next take installation diskattached to the router. And launch the installation of drivers and software.
3. After that, we need to configure the computer to work with the router. Now we have a network card set to the Internet directly through the provider. So, perhaps, some data is prescribed in the control panel that it is important for us to save and use after that when working with the router. To do this, go to the TCP / IP V.4 protocol settings as shown in the diagram:

   For Windows XP: "Start\u003e Control Panel\u003e Switch to Classic Application\u003e Network Connections.

   In Windows 7: "Start\u003e Control Panel\u003e Network and Internet\u003e Network Management Center and common access \u003e Manage network connections\u003e Adapter parameter changes.

   In the screenshot, I go to the settings " Wireless connection"But you still don't have it, and since we have connected a computer with a router cable, then you need to select the" Local Connection "item:

   

   If you have something indicated here, write this data on a piece of paper. This is especially true for those who have lost their contract for the provision of services and does not know the data for the Connect to world Wide Web. With a certain type of compound, which will be discussed below, it can be useful. After that, here, in the network connection options on the computer, you need to put an IP, gateway and DNS to automatic. We will already enter these parameters in the wireless router itself.

4. After that, go to the address "http://192.168.1.1". Usually configurations with the router occur here, if they did not have to do at the installation stage of the software. But you look at the instructions for the device, what path goes to the router control panel. Since the default IP on different models may differ. Also another popular place of placement of brief instructions is a sticker on the bottom of the device. Look and there. If there is no indication instructions, or it is lost, then go to the control panel, as I have already described above. Only after clicking the right button on the "Connection on the LAN" in the window that appears, press the "Details" button. In the window that opens, we look for the IPv4, the main gateway is the IP address of the router.

   

5. Now, finally, go to the address indicated there through the browser (http: // ip address of your router). And we find in the menu item DHCP Server (in the Trend it is combined with WAN) and set the range of values \u200b\u200bfor possible IP addresses of devices within your local network. I had it like this: Start IP - 192.168.10.101, End IP 192.168.10.200. And of course, in front of the DHCP Server item, the Enabled parameter should be. Domain Name or Host Name - then the name of the future home WiFi network. Immediately make a reservation that the screenshots below are made with my devices that already work or worked for several years. Their interface is in English, so it is easy to figure out what the domestic newcomer would be immediately not easy - I hope that these pictures will help you. Most of the modern firmware and software are already in a Russified form, so it will be even easier to understand.

   That's how it looked in the trend (highlighted in red):

   

   And so in ASUS:

   

Configuring a computer connection to a router via LAN

Now we will specify the parameters for our WiFi home-IP network and a router mask. For a trend, this same item (see Figure 1 is highlighted in green), for the ASUSA - the WAN & LAN section - at the bottom of the settings page itself. In the first case, I asked IP 192.168.10.1, in the second - 192.168.1.1. This address inside the local network, by which we can go through the browser to the admin. And through which computers will access the Internet. Mask - default, 255.255.255.0

Connecting a WiFi router to the Internet via the WAN port

These were all the flowers, now the most interesting - setting external connection Router to the Internet.
There are several types depending on the settings of the provider. It happens in the WAN menu.

There are some more options for connector to the equipment of the provider, but they did not come across. Therefore, I will not speak about them yet.

How to encrypt connection to WiFi network

If you did everything right and saved all the settings, all devices that support WiFi should now see the new network with the name you specify. However, on this question, how to connect WiFi at home is not yet closed. The WiFi home network turned out to be open, that is, anyone can take advantage of your internet access to freebies. To break all and make a WiFi network at home available only for its owner, you need to protect the wireless network.

There are several ways, I used two WPE (or Shared Key) and WPA in my practice. The latter is more reliable, so I will consider it. Go to security settings. In TRENDNET, this is the "Security" menu item, in Asus - "Wireless\u003e Interface".

Select in the WPE or WPA Personal menu (PSK, TKIP), set the password for authorization - from 7 to 64 characters. And save. Showing how it was for me:

Well, now to enter the Internet through your router, you need to enter a password. Last bar remains - so that there are no problems with connecting to the router of all sorts of devices and with the work of the programs, set by manually DNS server. Setting this parameter is located there where the parameters were entered to connect to the Internet. We activate the manual destination function of DNS servers and spanking IP from Google:

• DNS-PRIMARY (or DNS server 1): 8.8.8.8
• DNS-Secondary (or DNS server 2): 8.8.4.4

You can also specify one of the Yandex servers (for example 77.88.8.8).

As you can see, connect WiFi through the router and make a WiFi network at home quite simple. I hope you, too, everything will work!

Now the traditional video for the dessert for connecting the router, which even more understandable will tell about the typical settings for working with the network.

Good day to all!

As a rule, when connecting and configuring home Internet, it is required at least once to go to the router settings by connecting to it with a network cable (via LAN-port). At least in order to set up a Wi-Fi network ...

In general, usually problems arise more with wi-Fi setupWhat is directly connected to the LAN port of the router. However, in some cases, interesting "incident" occurs: when the computer and the router connected the cable, but for some reason the network icon in Windows reports that there is no connections - the cable is not connected (and the icon is lit red cross).

In general, in this article, we will consider consistently all the actions for connecting a PC / laptop to the LAN port of the router. I think the article will be useful for all novice users who are trying to set up home network.

Connecting to a router with a network LAN cable

I'll start immediately from the room in a quarry ...

1) The first thing we need (except for the router and PC, of \u200b\u200bcourse) - is network cable. In general, usually, such a cable comes complete to the router (in 99% of cases). Most often, the length of such a LAN cable [from a set] is not more than 1 ÷ 2 m. This length is quite enough [in most cases] to connect and configure the router.

Note! If you do not have it, or its length is clearly not enough - you can buy it in any computer store. And, there you can also ask you to cut the cable for a specific length ...

Network cable (1-2 m. Cable comes complete to all routers)

2) Next, connect the power adapter to the router and turn it on. Then connect to the "Internet" jack of your Internet provider. One of the blue (often they are yellow) Ports (LAN) must be connected to a lan-port / PC network.

With computers, as a rule, no problems arise. Most models have at least embedded in the mat. Card network card, and its port is easy to find on the rear wall of the system unit.

With laptops - maybe everything is somewhat different. The fact is that modern laptops, usually connect to the Internet using a wireless network, and not on all devices there is a LAN port. If you have a LAN port, it is necessary to purchase specials. Adapter Adapter on USB ...

Adapters such quite a lot: there are suitable as a classic USB 2.0 / USB 3.0 ports, there are more versatile (with support for LAN, HDMI, USB) for USB Type-C. See Screenshot below.

Note! You can purchase such adapters for "penny" in Chinese online stores. About the best of them told in this article:

3) If both the computer and the router are turned on, with the cable everything is in order - then on the router housing you should see how you will burn (blink) several LEDs: responsible for food, LAN-port, Internet (if the connection is installed).

LEDs tanned on the router (including, the LED, which is responsible for the LAN port caught fire)

4) Ideally, you should see in a tray network icon network without any warnings (signing that the connection to the router is installed, the Internet is).

Network icon (Windows 10). All OK!

But, unfortunately, in some cases, it is not always a router immediately automatically starts to work (sometimes without manual setting - no way) ...

Why after connecting on the network icon of the network "burn" an exclamation mark (without access to the Internet)

Perhaps this is the most popular option (especially when you first connect and configure the router, for example, after the equipment change).

In this case, first of all, I will recommend open network connections And check whether everything is in order. To do this, press the button combination Win + R. And use the command nCPA.cpl (See Screen below).

How to open network connections || NCPA.CPL and WIN + R command

In the network connections window you need to open properties Your connection (usually, it is called "Ethernet" (as in my case) or "LAN connection").

• receive an IP address automatically;
• get the address of the DNS server automatically (in some cases it is recommended instead of auto-option, specify DNS 8.8.8.8 - this is a DNS from Google.).

Save the settings and check the operation of the network.

Second important moment - This is a check of the router settings. If you have not previously been configured, then, in principle, mostly the Internet cases and will not be indicated by the connection parameters. Different providers have different requirements: as a rule, find the necessary logins and passwords, IP addresses, etc. Parameters [which need to be entered in the router settings] It is possible in the contract with the provider, which was concluded when connected to the Internet.

To help! How to enter the router settings [just where you need to set the connection parameters] (for beginners) -

Setting PPPOE connection In the Tenda web interface (for connecting to the Internet)

Why after connecting on the network icon of the network "Light" red cross

This icon means that you do not have a connection between the router and the computer (laptop). This may occur for various reasons. I will give the most common.

1) Check the condition of the cable.

Whether everything is in order with him, do not bother. It often happens that externally, the cable may seem entirely, but it has been driving it very much, and inside the copper veins were interrupted. Therefore, I would recommend trying to use another cable.

2) Look, is the cable in the LAN-port tightly inserted.

Often due to small deviations in the manufacture (as well as rubber pads, which are often put on them, roughness, etc.) RJ-45 and LAN-port connectors - not always and not every connector is inserted into each port to the end. Ideally, after the connector was inserted - you must hear a light click (and on the PC / laptop network card - the LED should light up that the cable is connected (the same as on the router)). If a PC has several LAN ports - try to use another.

3) Check if your network adapter is enabled.

In Windows, it may be so to become that the network adapter will be turned off. To check if it is not, go to network connections (To do this, call the "Run" window with a combination of Win + R, and use the NCPA.CPL command) . Next, pay attention to the one icon: the device turned off is black and white (as on the screen below).

You can simply right-click on the adapter to see the status of the work and turn on the device (if necessary). See Example below.

Turn on Adapter / Network Connections

I also recommend entering the Device Manager (combination of Win + R, and the DevmGMT.msc command) and find your adapter in the tab "Network adapters". Next, try to turn it off / enable (just click on it right mouse button). An example is shown below.

To help!

On this all, all successful and quick connection!

All the best!

Welcome to you, dear readers of our site. We continue the cycle of useful articles, on setting up the equipment.

Most users who want to connect a router to a computer or laptop face the problem of connecting the router, due to ignorance of simple functions of this device. Smart Tronic will tell you how to connect the router correctly. In fact, everything is simple, read Next!

What can be connected router

This part of the article is for those who want to learn more how many modern router is a multifunctional. What can the router connect to? Here common list devices that can be connected to the router (this is its second name):

• A computer
• Notebook
• Game console
• Smartphone
• Tabletnik
• Electronic book

Here are the basic devices to which Router can be connected. Why do such a connection of all sorts of gadgets? To freely exchange information between devices and on each of them to have access to the Internet. You can connect the router by two different technologies: wired and wireless. The connection method depends on what kind of router you have (if it has Wi-Fi support) and on your desire. In this article we will tell about connecting the wired network. Read about wireless technology in others, not less useful publications on our website - .

So today, quite a lot of companies produce routers. You can connect the ASUS, D-Link, Zyxel, TrendNet, 3Com, TP Link, Netgear, and others. We want to say right away - regardless of what brand you decide to purchase a device, its connection will be the same as an alternative manufacturer.

Standard connection router

We describe the functionality of the usual router. This will help you understand what the connectors are needed on the router, and how to use them. How to connect the router? All simple! Let's look at the picture:

For proper connection, on a network cable, you need to do the following. Routher Connection Instructions:

1. Correctly clip vitua couple (UTP network cable), if necessary.
2. Enable the router to the power supply.
3. Connect network cables.
4. Set up a network.

Read about the tincture of the network in the article. Now, let's figure it out how to connect Router to a computer.

How to connect a router to a computer or laptop

So, you have a special cable-patchcord, which connects the computer and router. Naturally, it must be enclosed in the right way, according to the desired scheme, so that the router and computer will "see" each other. Patch cord must be stuck in one end to the computer's network card or laptop, and the other in Router. Where exactly is shown in the picture. It can be seen where to connect the Internet cable to Router. Routher Connection Scheme to Laptop or Computer:

Is it easy? Four can be connected to the router on the screenshot various devices on cable, not counting Wi-Fi connections. We hope that the article was informative.!

• Denis

  Tell me what could be the problem. I can not find, nor there is a beech, nor your smartphone through Wi-Fi ... Tell me it may be in the settings, somehow did something ... everything works well, the router through the computer installed, but connect other devices (((

• Smart Tronix

  Denis, usually, with a properly configured router, the network on a laptop or smartphone is automatically. It remains only a password to enter and connect.

• Max

• Smart Tronix

• Vitaly

  The guys can tell me the ancient everything installed firewood installed, the router found. Without wire, I want to use the Internet through the router. Tp Link Router tried another Connect the same through the cord there is a network itself on the radio channel. I see the network to do I can not, or make firewood taking configuration and connect to try again?

• Vasilisa Baranova

• Igor

  My Provider UTK. I used modem D-Link, everything was fine. Recently bought a Wi-Fi TP-LINK TD-W8961ND router. It fails to configure the installation disk! Through the browser too. Help! Now I am sitting like this: I connected my old D-link to TP-Link as a computer in port 1, the computer itself connected to the port 2. Wi-Fi is there, the Internet is on the computer too. But it should not be so! It is necessary that one TP-LINK has worked.

• Lia.

  Hello. Please tell me how to connect the router to the laptop to the laptop so that the wires of the wires should not be connected. Thanks in advance.

• Alexei

  Hello. I can't open the admin panel of the router ( aSUS model DSL-G31). When in the browser I specify the address 192.168.1.1, the browser cannot find such a page. The instructions do not have a word about the address you want to specify in the browser. True there is a footnote that the gateway: 192.168.1.1, DNS: 192.168.1.1. Please tell me that in this situation you can do. Thanks in advance.

• su_yuri.

• Tanya

  Hello. The computer does not see the router. Writes: Check the wired connection between the PC and the router. I checked everything, all the wires are inserted into the right place. Please tell me what is the problem?

• Michael

  Tell me please ... I am such a problem, when connecting a laptop to a router gives an error ... that Windows cannot connect to the DIR300 ... Although any other laptop connects ... first sinned on the adapter in the laptop, but then checked on other points, it works ... what's the problem ?

• Laura

  Hello! Please tell me:
  Available switch D-Link DIR100, the WAN port is connected to the fiber optic cable from the provider, in 1 port LAN-stationary computer, in 2 LAN-IP television port. Need to connect tP-LINK router With Wi Fi to distribute the network on a laptop. How to connect all devices?

• Dmitriy

  Hello. I use the Internet on a laptop with reference to the MAC address. Bought a router with Wi-Fi and 4 LAN outputs. Cloned the poppy address in the router settings and connected the laptop, both by LAN and Wi-Fi without problems. Prefix and phone numbers, too, without problems. I can connect on the LAN stationary computer with XP in general the network does not see what to do? Thank you.

• sanych

  I can not understand which wires you need to connect to the router, and from it to the laptop. Wired Internet is also needed, or the phone is home, something like you need ???

• Ivan.

  Good day! Tell me, is it possible to configure the router only for and using a laptop without resorting to a stationary computer? That is, simply no PC. Only a laptop, router and cables, how to be in such a situation?

• Julatte.

  Good evening, tell me, configured Trendnet router 652 laptop sees the Internet, and the smartphone phone and the second computer are not connected, but they see the router's network.

• sergey

• Maxim

  Hello! The Internet on the Bilainovsky computer works fine, connected and configured the D-Link Dir300 router, I find Wi-Fi through the phone and tablet, everything is well connected with a password. But the Internet is on the phone that it does not work on the tablet! IN network settings I tried to check the permission to other network users use the Internet connection this computer (She is removed). If I put it, then you can not connect to the Internet. (

• Yulia

  Hello! There was a problem, the D-Link router was connected normally. But now for some reason, the laptop does not connect to the router. Writes that windows cannot connect. What could be the problem?

• rock_stranger

  Hello. I have a question for you asking me to help. I want to do a home network at home through WiFi. Houses 3 laptop of them are two with Windows 7, one with Windows 8 and stationary WindowsXP (which is connected through the installed WiFi antenna). All are configured to WiFi Router and work without any problems for connecting the Internet. How do I do and through what and where to enter data if it is possible to show the entire network in detail. Since at the minimum description, I will not be able to understand. Thanks a lot in advance.

• Sergey

  Hello!

  I have a TL-WR740N when I run out the installation of Easy Setup Assistant, then it gives me an error "Failed to find a router. Please check the network environment. Please check the model of your router. " All of these items are in order. Can you please tell me what to do?

• GT_Smart.

  I have a big problem with the computer. My computer does not receive a signal from the router. First, it writes what is connected, and then the connection is broken and written that it is impossible to connect. What to do? Tell me (((((

• Vlad.

  Hello, I have on my computer connected via yusb modem, works fine. There is also a Wi + Fi router, but it does not have a port for modem in it. How can I connect the router after the computer so can I use the Internet on the smartphone via Wi-Fi? Help me please!

• Konstantin

  Hello! I connected a computer through a router, a laptop, a netbook is fine. When connecting the tablet, problems arose! The network sees, but after entering the password, it writes "connection to the IP address" and there is no access to the Internet. Tell me what to do?

• MICHAEL

  Hello everyone)) I have such a problem - a router sees through the laptop and enters it, and it does not enter the stationary computer through the wire. How can I make a landline computer working through a router on a wire?

• dmitriy

  Hello, I will go in router dir. 620, to the admin panel of the router, usually this is the IP address 192.168.0.1, through the browser by entering the login and password, it opens the settings and immediately comes to the login. What could be the reason?

• Alexander

  Hello. You need to connect the WiFi router TP-LINK WR340GD, but the problem is that the computer is used satellite Internet. The connection occurs in this way, first using any USB modem (operator) the Internet connection is installed, then with the Globax5 program, the satellite connection occurs, the satellite plate with a computer is connected coaxial cable via the Internet Card. Tell me how to connect the router and configure WiFi.

• Antby.

  Hello. Such a problem: I connected a USB printer to the router and configured it for a laptop under Windows 7. I tried to configure it for a computer for a computer under Windows 8, I did not work out - I register the IP router in address line Explorer, and instead of getting to the device itself, I get to his web interface. I just need to get on it through the conductor to further select and connect your printer. Maybe he explained to Savabno and I understand that most likely the decision is the simplest, but I can not find it. Router Zyxel Keenetic Giga, computer is connected by a cable, laptop via WiFi.

• Elena

  I looked at everything here ... There are adaptive firmware, which includes additional modems, but I can't understand there is my modem there or not. [...]

• Ksenia

  Good day! Purchased wi-fi router D-Link DIR-615, connected the provider cable to the Internet port on the router. Blue cable from a set in one end in the LAN on the router, the second to the port on the laptop, where the provider's cable was previously inserted. Now I can't go to the page of the router 192.168.0.1, because Writes there is no connection to the Internet.

• euro.

  Hello! Problem. There is a laptop without WiFi. At work there is a WiFi distributor. Can I remove the wire from WiFi working and insert to my network so that I have the Internet. And how can this be done? Thanks in advance, I have Windows 7 Home.

• Valeriya.

  I bought a router connected all cables entered in the browser row ah pi address everything opened, started to customize, and I was displayed, where it is written that the Internet cable is not connected to the Internet port, what to do? (all connected)

• vitaly

• vitaly

  The fact is that I live in rural areas and such an Internet will hardly hold it, and how my son falls under the distance learning program. And quite recently found out that the Moscow provider LLC Our network will put us a satellite dish for learning. Therefore, I asked such a question, but still, but still you can somehow connect it, because there is some way out.

• Nastya.

  Hello. Today I connected the router, everything seems to be in order, the phone sees the phone and finds, connects. Everything is in order, but it does not enter any Internet page. Why?

• Elena

  Probably write there, but still. Hello, I have such a problem, today I downloaded connectify program On the computer (Internet wired) and deleted it immediately. But after that I can not go into the Internet, as soon as I go out the window leaves, asks to enter a login password, a message from Broadband Router. As I understand it, there remained some router, I can not find anything related with him, tell me how to solve the problem.

• kirill

• Vitaly

  Hello. After cleaning the laptop antivirus program Disappeared between the laptop and the Wi-Fi router. Third-party compounds catches which were not used, disappeared. The router itself works, the smartphone and tablet Wi-Fi is accepted with it, for some reason there is no laptop.

• maxim

  Hello! I have this question: I have a TP-LINK TL-WR740N router. Can it distribute the Internet via WiFi without connecting to a laptop through the cable. If possible, how? Thanks in advance!

• maxim

  All set up, with a connected router with a cable Internet distributes perfectly, it is necessary to disconnect the cable from the computer the Internet disappears and distribution stops.

• Oleg

  Hello! Two computers are connected via router D-Link Dir 100. Until recently, everything worked fine. Now such a problem: on one of the computers there is no Internet, while there is a connection on the local network. The speed of 100 Mbit / s, packets sent once to 8-10 more than adopted (for example, 4365 Posted, 643 accepted). Browsers seem to try to open pages, but an error is issued on tabs. On the second computer, the Internet is working normally, and packets are transmitted - accepted approximately. Tell me, please, where to look for a fault? Thank you.

• Elena

  Hello. The router setup manual is written:

  1. with the help of the Internet cable, connect the WAN port of the router with the LAN port of the modem.
  2. with the help of the Internet cable, connect your computer to one of the router port.

  So, I have a question: Included only one online cable, and my computer is connected via USB wire to the modem, and not through the Internet cable, as written in the manual, what should I do?

• Tatyana

  Good day. I have a DLINK DIR 300 router and home television through Wii Fi. I want to connect a home phone (the operator has such a service - Beeline), but the phone is Panasonic KX-TG8205. Tell me what a cable need, to connect the phone LAN port of the router.

• Elena

  Hello, help solve the problem. Wai Fi Router Tr Link. The distribution of the Internet goes only on one of the devices. Laptop router sees, but there is no access to it.

• Bambina.

• Victor

  Good day. Faced such a problem. I have connected Wi-Fi Router Netgear, connected to a direct PC through the cable. The Internet works perfectly on the PC, but when I connect to the router from a laptop, such a problem occurs, the Internet connection disappears periodically, sometimes it happens every 5 minutes. It helps only reconnect. Please tell me what could be the problem.

• Nikolas.

  Hello, knowledgeable people! I have this question, I had a router DSL2740 with distribution Wi-FiBut the guys came from Rostelecom to bring the fiber-optic cable, and in my absence (the father is not very disassembled) replaced and the router also, it does not distribute Wi-Fi. So here's the question - is it possible in any way by connecting them between themselves, after all, to establish Wi-Fi to me? Thank you in advance for your help.

• Alexander

• tixero.

  I see people disassemble! Please tell me. It is possible to use the DLNA network if you use this connection method: PC \u003d\u003e (WiFi) router (cable) \u003d\u003e TV. I have already tried everything, I can not connect TV (with TV everything is in order to the Internet, but Dnla does not see). What could be the cause? Maybe in the settings of the router (b focus) you need to change something?

• Zik.

  Help! So I bought a router, I connected everything and then I decided to install firewood, but it was not there. The computer shows that there is no modem although it is connected! Rostelecom operators said that this is the fact that there are no drivers on the network card. This is true? If so, how to find out the name for the built-in network card?

• Nastya.

• Sergushok

  Hello!!! The question is the following, after flashing the router, all settings were complied with, the problem is that one laptop set up asked the key, introduced it. I tried on the tablet and on the phone, just without any problems, but I can't enter any other laptop, writes Windows failed to connect to DIR 320NRU 2. It does not even request the key, trying from the router to insert a short cable to this laptop, everything works, in What could be the problem, please tell me?

• Patia

• Marina

  Hello! I connected the Wi-Fi router to a laptop through the cable, set up a router, everything works. But as soon as I turn off the cable and I want to connect to the router through the Wi-Fi, it connects very long time and does not happen. I have to constantly sit on the Internet through the wires ((((Router I have TP-LINK TL-WR841N.

• Serge

  Good day, the router asus no wireless is there (from the phone and laptop) connected via the cable to the stationary. Sends, but does not accept, in general there is no Internet in the hospital. IP address and the rest of the Labuda introduced a password to remove?

• Sergey

  Set the router from the disk, connected the cable which is included in the access. Everything works and Wi-Fi (two phones) and a computer. Connect the second computer through the cable - it is not no.

• Sergey

  How to connect the second computer via a Wi-Fi router with a cable? When you connect the first computer, the Internet is there, and when you connect the second cable, then no. Drivers I downloaded today latest version. How to check the network connection properties?

• Sergey

• Nur

  PLEASE HELP WIFI Tablet WiFi Tablet The WiFi network is pushed, the browser on the tablet does not open the browser. What is the problem and how to solve the problem

• Dmitriy

  Dear smart Tronic, I have such a problem: I have a portable Wi-Fi router, but it is badly caught and not convenient to sit on the Internet - everything hangs. I decided to buy a big Wi-Fi Router, but I do not have a wired internet for him. Tell me whether he will strengthen the connection and Wi-Fi in the house so that you can sit perfectly on the Internet, and that would not hang anything.

• Anton

• lenyas.

  Hello! Tell me, please bought a TP-Link740N router, the computer is tied to the MAC address, the router connected without problems, the MAC address closed, Wi-Fi on the laptop and tablet, in phones There is. However, everything works without problems. But I wanted to connect the Samsyng TV via the port on the router, you cannot configure the Internet automatically, I tried to manually, but nothing writes to check the correctness of the IP address, it seems to enter everything true and nothing. But I understand that if the MAC address is tied, then how to change it in the TV. What should I do, tell me? Thanks in advance for the answer.

• Ruslan

  Hello! There is a TP-LINK TL-WR841ND, the problem with the van port, I connect the Internet cable once earned and stopped, the van port indicator does not burn ... I connect to the van comp. The indicator works. I did the firmware ... Thank you in advance.

• RUFM.

• Mira

  Hello! The programmer connected to me a TP-LINK router to a computer. Laptop network sees, everything works well. But the computer is no longer connected to the Internet. I have a house.ru. Writes: "Error 678. Remote computer Not responding. " What should I do now? Help me please!

• andrew

  i took the laptop from the repair. I can connect Wi-Fi. Press the network security key. Like the button back of the router. How to find out the security key? I connected the router not me. But documents and the contract I have.

• natasha

• Yulia

• Max

  hello! Please tell me the router is connected to the laptop and your smartphone see it and connected but the Internet is still not there. Well, when I connect the router with a laptop through the cable anyway there is no internet

• Irina

  Tell me how to set up the Internet at a stationary PC on a router. The router has been installed for a long time and works with laptops, the need to install the Internet also appeared on a PC, how to do it? In the apartment was made overhaul and a special squeezed for the Internet for a stationary computer was carried out, will it be through this socket to enter the Internet through the operation of the router and how can it be competent?

• serge

  i connect the network cable of the Internet provider in the internet connector of the DIR-300 wireless router, the second cable from the network card in the LAN1 connector, click the connection, does not connect.

• Andrew

  Good afternoon, I had a problem with connecting the TP-LINK N600 router. There is a signal from the Internet cable, on the router all the icons (what you need) are blinking, it seems that everything is properly configured from the disk. On the laptop it connects to the router, but it writes that there is no access to the Internet. Please help. (I apologize for the chaotic description of the problem)

• Rustam

  Hello on the computer I can not find the router! Maybe something I do not do something on Windows XP everything was good and on 7 reinstalled can not find.

• Anna

  Two laptops and a phone are connected to the WiFi router, the network periodically disappears on the laptop, then on the phone, not together, namely, on something one, per day is not peaceful. Restart the router and everything works. What is the reason???

• Tamara

  Help me please! They put another router (there was no problem with the first problems), both Dr. Link, it somehow it turns out the laptop: Skype works, and the browser pages do not open. The laptop router "saw", issued his name, the signal is strong. Apparently, something with the settings of the computer. But what?

number smart gadgets Applied in our homes, grows every year. Therefore, to have a good and stable WiFi network in each room becomes not a priest, but a vital necessity.

With it, you can easily combine all devices in the total local network With internet access.

The article will step by step and discussed in detail all the steps wi-Fi connections Router, ranging from choosing the installation site, laying wires and mounting the Internet sockets - where, how and how it is better to do it.

And ending with the most configuration of the Internet connection and network on the computer. Plus we will touch on the search question possible problems and faults.

Than connect

Let's start with tools and materials. If you install a router directly near the computer, then you will have enough factory patch of cord korde in the kit.

Then this stage Installation works can skip and directly move to the setting below.

But when WiFi router is mounted in the hallway on the wall, for a good distribution of the Internet throughout the apartment or at home, then some materials will have to be purchased here:

UTP5E or UTP6 is used, the so-called twisted pair.

You can take single or double, depending on the number of gadgets.

• directly Wi-Fi Router

Installation location Wi Fi router

First of all, correctly select the location of the router. It is from this that the speed and quality of the signal in remote rooms will depend largely.

In those who, in addition to the camshaft, are still mounted and the low-current shield, usually have it near it. In this case, there will be less twist with the connection and pulling the wires.

It is in a low-current shield and a cable from the Internet provider with an entrance of the house.

Who has no such shield, choose a place in the corridor on the wall in the upper part of it. The higher the better the signal will be.

At the same time, do not forget that there are places where it is categorically impossible to mount a WiFi router:

• Near the instruments operating at frequencies of 2.4 and 5GHz (microwaves, radiotelephones)

By the way, the frequency range of 2,4GHz in turn is divided into 13 channels.

This is done so that several different gadgets do not interfere with each other.
At the same time, it is not a fact that you will be able to find an absolutely empty channel, not busy neighbors. We have to search the most free to avoid further connections of connections and improve the quality of communication.

• Right opposite the mirror or locker with glass doors

• In a deep niche with a metal door

It also applies to a low-current shield. Some put a router into it, together with the rest of the rest of the lowest. For example, video surveillance.

Be careful and pay attention to the material from which the shield is made.

Connecting UTP cable and mounting online sockets

You can connect it as directly to the router, so make a separate outlet under it. Thanks to such a socket, the router you will not be tied to one place, and the design of the apartment will look much more cute. Compare a neat outlet with a lonely wire sticking out of the wall.

To not confuse it, sign this cable as WAN.

From this place where the WAN cable ends stretch the four-party UTP cables into the rooms where the Internet sockets will be mounted under all your other gadgets.

These wires include as LAN1-LAN2-LAN3, etc.

Of course, the router himself hangs under the ceiling, you need to somehow connect to the power. To do this, you do not need to pull a separate cable 220V directly from the shield. Make a connection from the nearest distribution unit of the socket group.

Stretch the cable WGN-LS 3 * 1.5 from the dispensing box to the installation site of the future socket 220V near the router.

By installing all wires, go to the installation of accessories - email, Internet sockets and connector. First of all, you need to connect the Internet power cable from the provider signed as WAN.

Remove from it an external insulation by 2 or 3 cm, and divor the multicolored veins on the sides separately from each other.

The correct connection can be seen on the housing of the socket itself. Install the veins in the inside and snap the lid.

All that remains to be done is to secure the Internet socket in the opposite and close it with a decorative frame. Exactly the same scheme made all other computer sockets near the router itself and in all rooms.

This would seem easy, you can initially make a bunch of errors, because of which you cannot configure your network. You will climb in the settings, reflash drivers, and it will turn out to be in an incorrectly mounted outlet.

How to avoid similar errors, it is described in detail in the article below. Be sure to familiarize yourself with it, especially if you have problems with the network.

Each exit on sockets is signed, and the router itself is fixed on the wall.

You can certainly purchase them ready, but they do not always go the necessary length. It is better to measure the size yourself, clean the wire from two sides and gently arrange the veins in a row according to the T568B scheme:

• white orange

• orange

• white green

• blue

• white blue

• green

• white brown

• brown

After that, carefully put the veins in the RJ connector until it stops and crimp the ends of the cable with a crimp. All the same thing is done and with the rest of the cordami patch for other devices.

It remains to connect the router itself. Find a blue connector on the back panel with the WAN inscription and patch cord connect it from the Internet power outlet from the provider.

Some manufacturers have the connectors can be the same color, see do not confuse. In this case, focus exactly by the name WAN. By inserting an Ethernet provider cable into the LAN connector, you will not have the Internet.

Also note that on old models, where the Internet is distributed on the telephone line, this connector has an RJ-11 format. Inside such routers is a built-in DSL modem. They are intended for those providers that provide an ADSL connection.

But this technology is already considered obsolete, and such modems are not so claimed, although they are applied.

Yellow output connectors - LAN1,2,3 are designed to connect wired Internet. Connect the Internet sockets through them in all rooms.

And further to them, their intelligent stationary gadgets - TV, consoles, etc.

Plug the power supply into the socket 220V and supply the voltage to the WiFi router.

Do not forget to switch the corresponding lever or the Wi Fi button to the ON position.

Otherwise, the device will work with you as an ordinary cable router, without creating a wireless network. If the router you do not have a new one, or set it up when checking in the store, you need to reset all the old default settings. It is done by a long press (a few seconds) on the RESET button.

You performed the physical connection of the router itself, it remains to configure it properly on the computer.

Routher Setup on Computer

Create to the computer to the corresponding connector patch Cord from LAN1. When connected, two light indicators should light up.

If you are included in the Disc, insert it and run the installation wizard.

In it choose your country, the city and provider from the drop-down list.

All settings from this provider are already sewn into the router. This helper will automatically determine the type of available WAN connection.

If there is no one in the list of your service provider, you will need to choose the connection type yourself. To find out, learn the contract, or call the technical support service.
The most common is a dynamic IP, where the address is prescribed automatically.

When the disk is missing, you dial the default address in the browser line, which is specified on back side Router.

Enter the username and password. They are also indicated on the sticker.

Or simply gain universal addresses 192.168.0.1 or 192.168.1.1. After that, also enter a password and name (Admin).

Passing it, fall on main page All settings. We will consider the settings on the example of the router from TP-LINK.

The first tab "Condition" gives general information In all parameters of the device. Including as a state of connecting the Internet signal.

"Operating Mode" - In this window, you can change the main modes of the wireless module of the router on the "Access point" mode or "amplifier WiFi Signal". Side is given a detailed description of these modes.

Now you can go directly to configuring the Internet connection.

When choosing " fast settings"Press automatic definition Type of connection and click Next. This process Very fast and adjusts the local network.

To configure directly the Internet yourself, choose the tab "Network" and then the WAN subsection.

In the window that opens, call a list of available connections. The default is the dynamic IP.

If your provider uses this type, then in fact no settings in this subsection do not need to be done. The router himself will work for the IP address, subnet masks, etc.

The next type is "static IP". This type of connection is the full opposite of the first, since all network parameters will have to be administered manually. All the necessary information should be provided with the provider.

Paragraph L2TP - This type of connection is one of the varieties of VPN connections. Therefore, for a connection to introduce a lot of identification data.

Login, password, IP address server. With the latter, be careful, as it can be used both dynamic and static address, which of course increases the number of information entered during the setting.

Next "PPTP connection". By setting it is similar to the previous L2TP.

Last tab "Bigpond cable". Very rare connection and consider it within this article there is no point.

Let us turn in more detail by the third type - PPPoE. Very often it is to use the Internet Provider Rostelecom. Here it is necessary to register a login and password, which are specified in the Treaty of Internet Services.

All other data is desirable to leave unchanged. After that, click "Connect" and "Save".

On this settings manually, the connections are over. Now you can open any Internet page to check.

Sometimes a bad connection can be caused old version Built-in software. To check the relevance to return to the "Status" tab and remember or write down the data on the above.

After that, in the search engine, enter the version of your device with the control phrase "Official Website". Select the desired link and check the equipment version.

In the screenshot it is V5. Go down below and click the "Built-in software" tab. It compare the latest available version with installed on your router.

As you can see in this case, the update is not required.

Setting wireless mode Routher.

Now consider in more detail wireless mode. To do this, select the corresponding menu item on the left and subsection "Basic Settings".

In this window you can change standard name Networks on arbitrary.

The mode and width of the channel change in the event that any of your wireless devices Communication has problems with connecting to this WiFi router. In other cases, these parameters are better to leave the default.

So your router changed the network name. However, the password remained the same who walked from the plant. Therefore, find your network with a new name and click Connect.

Next, enter the previous security key. New Network Connected. Return to the settings menu.

The next WPS subsection.

In this window, you can enable or disable the WPS function, which allows you to quickly and repelly connect devices while pressing the corresponding button on the router housing.

"Wireless Protection" - This page allows you to make a network open or change the version, encryption type, and the most important password Wi-Fi network.

Since you changed the key network, you need to reconnect, but already with a new password. To do this, first "forget" old password In the Wireless Settings menu.

After that, reconnecting re-and prescribe new data.

On this, the main settings of the router are completed.

Connection errors or why WiFi does not work

What to do if you passed all the settings stages, and there is no Internet. Either once, after a long successful work, your WiFi network suddenly disappeared, or the devices stopped seeing it and connect normally.

Where to start looking for the cause, and how to solve it? There are many reasons and ways, we will list only some of the most commonly.

The first is the easiest, but nevertheless an effective and working way that helps in many cases is the elementary reboot of the router or computer.

When WiFi disappears only on one device, and there are on others, then look for a problem first of all on this device.

For example, there is no network on the web on the web, and the TV and the phone work normally. Very many errors are hidden in power supply wiFi adapter. Come on the following paths: Device Manager - Your Network Adapter Properties.

You select the "Power Management" tab and turn off the checkbox at the "Allow shutdown of this device to save energy".

If there are no networks on all devices, then the reason is in the router. To find the problem, find out if WiFi is working at all? To do this, it needs to be done open.

Come at the router settings 192.168.0.1 in the section wireless network And then remove encryption, exposing the value "Open System" or "Disable" depending on your model.

Also open the SSID network identifier.

If the wi fi appeared, then the cause is in encryption. You can try other methods of signal encryption, there are several of them there.

Another reason can be in the length of the WPA key. If there are too many characters in it, the router stops working.

By brute force with a gradual increase by one, you can pick up the maximum length.

Update firmware

If the problem is not in encryption or the length of the keys, then try resetting the settings to the factory and re-pass the connection procedure.

When it does not help, it is worth updating the firmware. On the manufacturer's website, look for the last actual version, download it and update the file.

Problems on the computer

If the reason for performance is not a router, but the computer itself, then check the properties in the device manager network adapter For WiFi network. When the device works fine, then the cant in the software.

And when the error clearly gets out, then update the driver.

How to determine what problem is in software? You can do this by control points of recovery. Restore the system from the last automatically created point and return Windows for a few days ago when the network was operational.

If everything goes well, the problem is definitely on the side of the operating system, or some other programs in Windows associated with Wi-Fi network.

Authentication error

With this error, the first thing to do is to check the password. If you doubt his correctness, and you want to know whether you enter whether you enter, you need to go to the router settings.

Again 192.168.0.1 - Security Settings - Encryption key.

When connecting the device to WiFi, enter it in the input field. If nothing has changed, you may have to reinstall drivers on a network card or network adapter.

With the other causes of malfunction not specified above, you can find a video: