entranceInstructions for using the split system Samsung. Review of Samsung air conditioners: error codes, window, household and wall models
Samsung AQ 09 UGF
Table of contents
Disposal
Name of each part
Selection of operating modes
Useful Tips
Cleaning your air conditioner
Precautionary measures
Disposal
Recyclable substances are used in the manufacture of this air conditioner. Therefore, check with your area how to dispose of according to local regulations.
Name of each part
Outdoor unit
1 - Air intake on the back-side surface.
2 - Air outlet, fan blades are visible behind the grille.
3 - Connections for connecting the refrigerant line.
Indoor unit
1 - Air intake to the indoor unit.
2 - Air outlet into the room. Closed when idle.
3 - Window for receiving commands from the remote control.
Remote control
Preparation before starting work
Before turning on, make sure the air conditioner is connected to an outlet with sufficient power and is properly grounded. Make sure that there are no obstacles to air movement around the outdoor and indoor units (curtains, etc.).
Install batteries in the remote control. Observe polarity and do not install different types batteries in the remote control.
Selection of operating modes
The following operating modes are available for this air conditioner:
... Automatic - you set the desired temperature range and the device automatically turns on heating if the room temperature is lower or cooling if the temperature is higher.
... Cooling - maintaining the air temperature in the room not higher than the value you specified. In this case, a dehumidifying effect is noted.
... Drying - a mode in which the air conditioner dries the air, cooling it as little as possible. In this mode, you cannot set the desired temperature.
... Heating - keeps the room warm.
... Ventilation - simply keeps the air in the room circulating.
Useful information: in heating mode, the air conditioner does not turn on the indoor unit immediately, but after 3-5 minutes. This is necessary to warm up the heat exchanger and protects the user from cold air supply. In addition, in this mode, freezing of the outdoor unit occurs, therefore, the operation of the air conditioner periodically stops (no more than 10 minutes) to defrost the frozen parts.
The indoor unit is made with improved aerodynamics of the air cavity, therefore it works quietly and efficiently.
Additional modes and settings
This model compares favorably with a number of useful modes.
During operation, you can set the fan speed, which affects its volume and heat exchange rate.
You can manually specify the direction in the vertical plane and rotate the horizontal guides so that air from indoor unit walked constantly to the right or left.
The TURBO function is used with air cooling mode. Allows in a shorter time to cool the room to the desired numbers.
By using the good sleep function, you can get better sleep. Set the air conditioner to the time when you go to bed, the time to sleep and wake up, and it will independently maintain a colder temperature while falling asleep, slightly raise it during sleep and help you wake up invigorating with a portion of cold air.
There is also an on and off timer. The first one sets the time when the air conditioner should turn on. The second indicates the shutdown time. Thus, you can program the device to work independently at certain hours.
Available for cooling mode special treatment Smartsaver. By turning it on, you save energy, since the air conditioner keeps the temperature range in the room from 24 to 30 degrees. If you want to set a lower value, you will have to disable this mode.
During operation of the air conditioner, its indoor unit is constantly in contact with condensate, which promotes the growth of fungi and mold in the air cavity of the unit. This mode should be used from time to time to prevent the appearance and growth of mold.
Useful Tips
Do not turn on the air conditioner to the maximum and overcool the room. You can harm your health and this will lead to waste of energy.
To rationally use electricity, you need to monitor the position of the horizontal partition. When cooled, its direction should be closer to horizontal, when heated - closer to vertical.
Make sure that the windows are closed directly during the operation of the air conditioner, but do not forget to ventilate the room when the air conditioner is in operation for a long time.
Check and clean the air filter regularly - this saves energy.
To cool the room faster, first turn on the fan to TURBO mode.
Cleaning your air conditioner
Use a secure footing when cleaning the air conditioner. Do not forget to turn off the air conditioner using the remote control and then unplug it. Perform all actions with dry hands.
Do not use gasoline, solvents, abrasive detergents and hot water (more than 40 grams Celsius) to wash the air conditioner - all this can spoil appearance plastic.
If you think there is a problem
The air conditioner does not work. Check if the plug is connected to the outlet, if there is power in the network, if the normal voltage figures are not exceeded.
The device fails to turn on for 3 minutes after turning off. This is a normal protection against frequent engine starts. Wait and turn on the device after 3 minutes.
After turning on the heating mode, the indoor unit does not start working immediately. This is a protection against cold air blowing - wait until the heat exchanger warms up and the fan starts working.
When operating in heating mode, the indoor unit sometimes turns off. In this mode, it is necessary to periodically defrost the outdoor unit, so the operation of the air conditioner will stop periodically.
During dehumidification operation, the indoor unit is periodically turned off. The task of the air conditioner in this mode is to dry the air while minimally cooling it. Therefore, the indoor unit will shut down periodically.
After a power outage and the appearance of power in the network, the air conditioner turned on independently and began to work, although no one controlled it using the remote control. If the air conditioner was working before the power outage in the network, then after the power appeared, the automatic restart system turned it on to work in the same mode.
Water flows from the outdoor unit. This is normal, because when the air conditioner is operating, the heating main and other parts are cooled and condensation appears on them. In defrosting mode, ice is removed from the heat exchanger of the outdoor unit.
White smoke comes out of the outdoor unit. When the air conditioner heats up the room, cold air flows out of the outdoor unit, causing fog to appear.
Mist comes out of the indoor unit. If the air in the room is humid and the air conditioner is operating in cooling mode, the moisture will turn around the cold air stream leaving the air conditioner into mist.
The remote control does not work and the display is faded. Check the presence of batteries, the correctness of their installation, replace them with new ones.
The air conditioner does not cool well. Check if the windows, doors in the room are closed. Whether direct sunlight is heating the room, whether there are additional heating devices working. Is the operating mode set correctly?
The air conditioner does not cool / heat. This can happen if there is a refrigerant leak. Call the installer for advice and repair.
The air discharged from the indoor unit has an unpleasant odor. Perhaps the source is a wall, wallpaper or carpet near the indoor unit.
The indoor unit makes a crackling noise during operation. The change in temperature causes the plastic to change in size, which causes similar sounds.
Gurgling is audible during operation. This is normal as the movement of condensate and refrigerant can cause similar sounds. If a gurgling sound is heard when the air conditioner is off, this may be due to air being sucked in through the condensate drain hose during the operation of the exhaust ventilation.
When the air conditioner will not be used for a long time (At the end of the season of use)
If you are not going to use the air conditioner for a long time, then you need to prepare it for downtime.
Turn on self-cleaning mode to dry the water in the indoor unit.
Then turn off the air conditioner using the remote control.
Unplug the power outlet.
To turn on after a period of no operation
Check if there are any obstructions in the air flow around the outdoor and indoor units.
Connect the plug to an outlet with the correct wattage and make sure the air conditioner is properly grounded.
Install batteries of the same type in the remote control.
Turn on the air conditioner.
Installation site and electrical work
Installation work must be carried out by experienced professionals. The same applies to working with the mains.
Please note that the outdoor unit may make noise during operation, which may annoy people living nearby. The location should be selected so that there are no obstacles to the movement of air and it is possible to drain condensate.
Precautionary measures
The power cord must be connected to an outlet with sufficient capacity. Do not plug it into an extension cord.
Always use the instrument with a good earth connection.
Do not pull on the power cord, place solid or heavy objects on it, or step on it.
Do not insert fingers or pencils into the access holes of the air conditioner, otherwise injury may result.
Do not stand or place foreign objects on both air conditioner units.
Fasten the outdoor unit with high-quality, serviceable fasteners.
Make sure the power plug is clean and use only dry hands.
Do not modify, repair or change the power wire, air conditioner components.
Do not unplug the power plug while the air conditioner is running - first unplug it using the remote control.
Do not stay under a stream of cold air for a long time - this can harm your health.
If any oddities in the operation of the air conditioner (burning smell, strange noise) appear, turn it off, unplug it from the power supply and contact a specialist.
If the air conditioner stops heating / cooling, then it may be a refrigerant leak - contact a specialist.
Be sure to unplug the power plug before cleaning the device.
Ventilate the area while using the air conditioner.
Unplug this apparatus during lightning storms.
Any modern Samsung air conditioner is created taking into account the fact that control should be as easy and intuitive as possible. Only a correctly selected remote control allows you to successfully adjust any model of climate technology. Unsurprisingly, the remote control is becoming an essential accessory on which the impression of a Samsung air conditioner largely depends.
Each buyer should understand how to choose the right remote control for further use of the air conditioner. It is necessary to take into account not only the cost of the model, but also its other parameters:
- high quality, which is guaranteed only when using original spare parts and components throughout;
- correspondence of the remote control and the Samsung model;
- the level of functionality, since the remote control must have all the necessary buttons to operational setup climatic equipment;
- ergonomics of the case.
It is important to note that the Samsung air conditioner will show the optimal level of functionality: the control panel, the instructions from which are attached in each case, will help to carry out a successful and easy adjustment of the used climatic technology.
Functionality of Samsung HVAC control panels
Any modern remote control for Samsung is successfully used only if it is equipped with charged batteries. In each case, two 1.5VAAA batteries are required.
Each control panel must have basic functions for the successful operation of the air conditioner.
- Mode (Mode) - button to select the optimal operating mode of the air conditioner.
- Auto - automatic mode for setting the temperature and maintaining it. The fan speed is determined by the room temperature.
- Cool - cooling mode with the obligatory setting of the optimum temperature.
- Dry - dehumidification mode for removing excess moisture from the air in the room in order to give freshness.
- Fan mode is suitable for ventilating the room, so that stale air is not allowed in.
- Heat mode is intended for heating the room. In most cases warm air served in 5 - 7 minutes. During the first few minutes, cold air is heated by an air conditioner, so it is not supplied directly to the room.
In each case, you can adjust the direction of the air flow, which contributes to the enhancement of the functionality of Samsung air conditioners:
- vertical;
- horizontal.
Modern remotes for Samsung air conditioners have a Good sleep mode, which guarantees the creation of the best conditions for falling asleep, sound sleep and waking up. As a result, optimal comfort in the bedroom is guaranteed at any time of the year, and the operating time of the air conditioner in Good sleep mode can be adjusted from half an hour to 12 hours.
The remote control for Samsung air conditioners is the ability to successfully adjust the conditions in the room, regardless of the personal wishes of the person.
Almost everyone knows the name of the company "Samsung", it is not surprising, because it is a conscientious manufacturer and world leader in the production of not only split systems, but also many others household appliances and electronics. Samsung's development history began in 1938. The firm was founded by a man named Lee Byung Chol. Oddly enough, but initially it was an organization that had nothing to do with advanced technology and electronics. Samsung's small grocery sold goods made in the Korean town of Daegu. Samsung began to engage in the production of electronics only in the 1960s and during this time was able to achieve heights in her business. V this moment the board of directors of the company includes the grandson of the founder of this corporation.
Varieties of air conditioning systems
To save people from the heat of summer or the unpleasant sensations of turning off the heating in winter, air conditioners were invented. Many people, tired of the uncomfortable air temperature in their own home, buy household samsung air conditioners, it is enough just to not only install them, but also to dismantle them if necessary. To choose the right model of the device, you should first familiarize yourself with all the characteristics of different types, because it is impossible to buy a universal device that is suitable for every customer. For ease of installation and use, manufacturers release different types split systems, each of which meets different user requirements:
Inverter
Samsung inverter air conditioners differ from other models by the presence of a unit power electronics helping to get alternating current required frequency. It is she who determines the speed of rotation of the engine. Such an air conditioner is able to smoothly change energy consumption and performance. The inverter allows you to very accurately maintain a given temperature regime and save energy.
Floor
The mobile floor unit does not have a lot of power, but it can be easily moved within the apartment and within the reach of the power source. Its complete set includes only one independent unit.
Vents
If you need to purchase the most simple cooling device, then the choice falls on samsung air conditioners or window air conditioners. Ease of use is ensured by the convenient location of all parts of the split system in one monoblock located under the window.
Wall mounted
The most popular solution is samsung wall-mounted air conditioners. Such devices are located on the wall under the ceiling and do not clutter up the space. Their external data help to be invisible in the interior and fit into any room, which is very important for a home split system.
Multizone
In buildings with several rooms, multi-zone air conditioners are used. Multi split systems are needed if you want to maintain a different microclimate in different rooms. Multi-split is cheaper than buying multiple air conditioners.
Cassette
Ceiling cassette industrial air conditioner. He is trusted with large volume air conditioning. Due to the distribution of air in four directions at once, such a device effectively cools the air.
Duct
Channel semi-industrial air conditioners. Cold air is distributed through the ventilation ducts, all equipment is hidden in the space above the ceiling, only the air distribution grilles are visible.
Column
Column air conditioner. Such systems do not require complex installation and are powerful at the same time. With a large enough volume, they do not take up much space due to their vertical shape. It is advisable to install these split systems in rooms with a large air volume. VRF systems. There is no fundamental difference between them and VRV. Both systems have a variable refrigerant flow. The price of it, the size of the case, the complexity of installation and connection of the split system will depend on the type of cooling electrical device. You can't save on Samsung split systems, because they are installed for a long time, and they give warmth in cold weather or cool in hot weather.
Comparison of characteristics of popular models
| Model / Parameter | ar09hqfnawkner | ar07hqfsawkner | 12 |
| Cooling, kW (device marking) | 2,75 | 2,05 | 3,50 |
| Heating, kW | 2,9 | 2,1 | 3,80 |
| Noise level, dB | 24/35 | 24/33 | 26/36 |
| Modes of operation. | Ventilation, night, temperature maintenance, dehumidification | Ventilation, night, temperature maintenance, dehumidification | |
| Power consumption for cooling / heating, kW | 0,857/0,803 | 0,639/0,582 | 1,090/1,115 |
| Remote control. | Yes | Yes | Yes |
| Overview of additional functions. | Deodorizing filter | Deodorizing filter, fine filter |
Manual for control panel and air conditioners SAMSUNG
Each device is equipped with a signal receiving board, whose firmware allows the mechanism to be controlled remotely. The manufacturers of split systems tried to make the remote control for the Samsung air conditioner as easy to use as possible, but it is still strongly recommended to study the technical data sheet before using it, without it, the use of the air conditioner can lead to breakdown and replacement of spare parts. Just a few simple buttons enough to control the mechanism:
- Power button. It starts the starting capacitor, turns on the motor or turns off the system.
- Switching operating modes. When pressed, it changes the mode in a circle. When setting the mode, it is necessary to select the temperature at which this household appliance can work correctly in the selected mode.
- Button for setting the required temperature. Helps to control the microclimate in the house. In fan mode, the button remains inactive.
- Fan speed selection.
- You can set the timer and select the start time.
It is worth paying close attention to the temperature range of the mechanism specified by the manufacturer. For example, if the air conditioner is used in too cold conditions, icing and cold damage can occur to important parts of the air conditioner: the compressor, fan blades, heat exchanger. This will lead to a breakdown of the mechanism and subsequent repair with replacement parts for spare parts.
It is necessary to clarify the temperature at which this or that model of the samsung air conditioner works without any complaints in the instructions for this model.
The instructions for Samsung air conditioners are easy to understand. All the necessary information is indicated on the screen of the remote control. The most important thing in the instructions is the scheme according to which the Samsung air conditioner is installed. A few tips for using the air conditioner:
- When the room is overcooled due to turning on the device to the maximum, it consumes more energy and is harmful to health.
- Electricity will be consumed as efficiently as possible if the impeller of the device is directed horizontally when the device cools the air, and almost vertically when it heats the air.
- A clean filter will also help reduce energy consumption. It is necessary to periodically check and clean the filters, in order to clean the inside of the device, it is necessary to disassemble it and remove the filter. Before that, you must unplug the device from the outlet. Cleaning with solvents or abrasive substances is not allowed, they spoil the appearance of the plastic cover.
- During the operation of the device, it will not be superfluous to check the windows again, they must be completely closed.
- For faster cooling, turn on the fan first.
- Servicing the appliance requires a professional to fill in refrigerant periodically. It is worth refueling at a service center that has a certificate and gives a guarantee. Only professionals can assemble and disassemble the device. Unfortunately, it is impossible to trace how much freon the master pours, we can only hope for his experience and the particularity of the service.
SAMSUNG air conditioner error codes
Error codes for Samsung air conditioners help to make an independent initial diagnosis of malfunctions of a household appliance. Repairing the Samsung air conditioner will not cause any difficulties after decoding the codes, because this information will help the master to quickly identify the breakdown and repair the device.
Some models of air conditioners are equipped with text mode. To enable this mode, you need to hold down the power button for about five seconds. The unit will report the presence of an error in operation using the indicator lamps on the panel of the indoor unit, which will either blink or light up in given sequence... The second will happen if there is an already identified error. If several errors are detected at once, then the system will first report a more dangerous malfunction.
Translation of the most common mistakes:
- The temperature measurement of the indoor unit heat exchanger is not correct.
- Incorrect fan speed. The error appears when the speed does not go beyond 450 rpm for 20 seconds.
- Incorrect measurement of the temperature indicator of the indoor unit.
- Icing of the outdoor unit.
Testing the device for faults occurs simultaneously with the automatic activation of the cooling mode. But the operation of the air conditioner at this moment undergoes some restrictions. Test mode requires entering the cooling mode. It will work regardless of the set or internal temperature.
As soon as an error is found, its code is displayed on the screen and the user can diagnose it. The designation of errors corresponds to one of the codes, the decryption is attached to the instructions for the device.
If all the LEDs are blinking, without any order, then this may mean that all firmware has been deleted. In this case, flashing will help.
Often people who have just bought an air conditioner do not know which side to approach it, where to press, etc. Today we decided to help you deal with the remote control from the air conditioner, which is your main assistant in creating a comfortable temperature in the room. After reading this article, you no longer have to ask yourself the question: "Am I using the air conditioner correctly?"
Of course, there is a wide variety of remotes, moreover, each brand has its own design. However, every manufacturer, no matter how extravagant it may be, tries to make the remote control as easy to use as possible. Thus, it creates universal keys (of the general standard), by clicking on which you can quickly set the necessary parameters.
The first and foremost advice for novice users is to read the instructions. Of course, you can refer to laziness, you can think that the instructions are a trifle. However, it is in it that the most important characteristics are written that you will need when using a new device.Now we will sort out in order the possible keys that are found in wired and wireless air conditioner remotes. All the names are written in English, but you should not be intimidated, gradually you will remember everything and you will easily control the temperature in your house.
Most popular buttons
These buttons are most often found on the air conditioner consoles and this instruction applicable to many models.
Mode- mode selection ( automatic work, cold, dehumidification, heat, ventilation)
Fan- (this is not the same Fan as in Mode)
The Fan button is to set the fan speed (3-4 different levels speed)
Swing- direction of the horizontal flap (directs the air flow)
Press once, the flap will begin to swing up and down constantly, when pressed again, it fixes its position. Some models have the ability to set the direction of the vertical flaps, if this function is not there, then they must be adjusted manually, pointing in the desired direction. Direct air flow onto a person is undesirable.
Temp- temperature (set, inside - outside).
You can find out the set temperature in the air conditioner settings, the indoor and outdoor temperature (there is not always a thermometer on the outdoor unit of the air conditioner).
Sleep- sleeping mode.
Reduced fan speed to keep quiet. Every hour for 2 hours there is an increase in temperature +1 from the set one. Then the temperature is kept at that level, and after 6 hours the air conditioner is turned off. During sleep, our body temperature drops, and this function does not allow us to get sick / freeze. For details, see the instructions.
Clock- clock (shows the set time). Set the time using the temperature arrows
Time on (off)- on / off the air conditioner by timer (do not forget to set the current time Clock)
Setting the time for turning on and off the air conditioner with latest settings mode and temperature. Pressing the button again disables the timer. The time is adjusted with the temperature arrows
Turbo- mode increased productivity(increases the rotation speed of the indoor unit fan).
Attention!Do not forget that you should not turn on the air conditioner for heat at -10C degrees Celsius. This may damage the air conditioner. Equipped only winter set air conditioners can operate at low temperatures (up to -40C).
Let's consider the rest of the keys:Each brand and model of the air conditioner has its own "chips". Let's take a look at some buttons with additional modes and functions for the air conditioner.
Smart Saver Is a very important feature that usually pleases economical users. If you set this option, then the air conditioner will reach a certain temperature set by you, and then stop working. This is very convenient, then your room will not be too cold or too hot: if the temperature starts to change, the air conditioner will turn on again. Thus, the temperature will be kept at a certain level.
The Qulet button provides enhanced diffusion of the cold air supply, thus reducing the risk of illness from direct pressure to zero. A very important function for rooms where children are often.
Auto clean- a button for disinfecting the air conditioner itself and drying its parts. This feature helps the device itself very well, you should press the key every few days to help the device remove moisture. Thus, fungus will not form in the air conditioner.
Good sleep- this button will help you to put the air conditioner in the “half-sleep” state: the device will work, the blade will be slightly open and cold air will be directed to the ceiling. This mode does not allow you to get sick, does not interfere with sleep.
Eco- the button is responsible for the power saving mode. The air conditioner starts to operate at low revs. Used to maintain an already cold room.
Ok and Cancel- button to confirm and cancel commands.
Indicators and signals
Many models have a display on the inside of the air conditioner that shows you information about the preset settings. Most often, the temperature set for operation in the set mode is displayed (sometimes the set mode is displayed).
If you don't have a display or you poor eyesight, then you are guided by the information on the display of the remote control. You can also control the set parameters by the sound signal of the indoor unit. When each button is pressed, the air conditioner unit emits a “pip” sound, indicating that it has received a command from the remote control. If no sound is heard, press again.
Thanks to this simple knowledge of the remote control, you will always be in perfect control of your equipment. It will only bring you positive emotions and set the perfect temperature in your home.
06.02.2018
Air conditioner remote control instruction samsung - added link
Remote control for samsung air conditionerAfter 12 months from the date of manufacture, the batteries may be 100% discharged even if not used. Such a system simplifies life and promotes a comfortable state of the person. Models of unique remotes are given in the codes section irc remote 16 e samsung. In this case, start the function from Fri 1.
If the range of operation of the remote control is significantly reduced, change the batteries and press the acl button with the tip of a ballpoint pen or other narrow object. web shop selling remote controls for. If two or more air vents are installed in the room, contact your supplier to set personal alarm codes for each air conditioner.
Remote controls for samsung air conditionersIf you are not satisfied with the swing spectrum, use the vertical airflow button on the remote control to configure the swing spectrum. Place your fingers on the front of the grille and lift it up. in addition, if the unit is used in cooling and drying modes at a lower temperature than indicated, the heat exchanger may freeze, which will lead to water leakage and other damage. You also need to create a faithful and not expensive in Moscow and Moscow. We also attach a description of the control panel. a short description of air conditioners from the manufacturer lg. Samsung air conditioner control panel annotation - annotation manual for the air conditioner samsung purchase. Complete annotation to the universal irc-16 e samsung control panel. There are two types of remote control devices.
Samsung air conditioner control panel manual
Samsung air conditioner control panel manualInstallation at your service air conditioners SPb It is already difficult for a modern person to imagine their existence without comfort and convenience. Installation air conditioners St. Petersburg will help you make sure that negative weather conditions do not affect your mood and quality of life at all. And if you needed installation air conditioners St. Petersburg, welcome to any of the leading companies in St. Petersburg. Mobile and window air conditioners are of the 1st type air conditioners... All components of such air conditioners(this is an evaporator and a condenser) are placed in one unit. The so-called split - systems (split - to divide) belong to the second type air conditioners... Correct mounting and installation air conditioners- St. Petersburg has enough specialized enterprises that will help to produce it in the premises you need. Installation air conditioners Petersburg is not surprising. They also offer a complete follow-up service. air conditioners... Petersburg specialists and professional installation designers air conditioners will help you calculate the required power of the device for a specific area, take into account the specifics of the room, tell you how to do it right choice the model and manufacturer you need. Professional assembly as well as installation air conditioners in St. Petersburg - required condition to ensure the smooth operation of split - systems and air conditioners during the entire period of their service. On Russian market all brands are represented air conditioners... Service centers guarantee you along with a quality installation air conditioners in St. Petersburg full service.
Compliance rate: 16.28%
Fragments of the post text:
Mobile air conditioner, Electrolux, is air conditioner the latest generation with all useful and possible functions and modes of operation (cooling, ventilation, heating, dehumidification, as well as the popular automatic mode), as well as a set of additional features. The device is quite lightweight and easy to use. management... Mobile home air conditioners are controlled by contrast electronic LED display with programmed buttons, as well as using a remote remote controlmanagement... Convenient and multifunctional remote controller Remote control is capable of transmitting signals to sensors management air conditioner even at a distance of up to 8 m, which allows you to choose required mode operation, setting the desired temperature regime (with an accuracy of 1, 1 C), set the desired start time by timer and perform other useful functions... The main and main advantage of mobile air conditioners is ease of installation. Scope of mobile air conditioners, in fact, it is limited only by the area of an apartment or house.
Compliance rate: 10.94%
Fragments of the post text:
So, the air conditioner, the indoor unit of which is fixed on the wall, is called wall air conditioner... But there are times when you need to manually select the direction of the supplied air conditioner wall-mounted type of cold air. This possibility is provided in latest models air conditioners... All leading (practically) firms - manufacturers of climatic equipment have recently been producing a wide variety of wall configurations air conditioners... Ultimately, the consumer when using air conditioner can enjoy the highest degree of comfort. Manufacturers of Japanese air conditioners.
Compliance rate: 10.85%
Fragments of the post text:
Typically, the cost of installing an air conditioner offered by the companies selling air conditioners, slightly higher than the one requested by a private master. Option when installation service air conditioners produced by those companies that sell air conditioners is optimal. Cheap installation air conditioners, carried out by a private owner, will not provide you with all the guarantees. There are options when cheap installation air conditioners offered by serious companies that are licensed to produce such works. Such companies offer not only installation air conditioners cheap, but also their full maintenance. There are quite a few models air conditioners and each of these models has its own specific features. It is in such serious companies that you can not only purchase climatic equipment with a full guarantee, but also order installation air conditioners cheap. As a rule, such companies have been involved in the provision of services to the public for a long time, therefore, installation air conditioners and sales are their main business. Others believe that editing air conditioners and sale is the prerogative of specialists in their field. After all, if the remote block of the climate control system needs to be installed on the wall of a multi-storey building, at a sufficiently high height, such an installation air conditioners should be carried out with the assistance of industrial climbers or using special aerial platforms.
Compliance rate: 9.79%
Fragments of the post text:
There are two common types air conditioners... Modern inverter control A home or office air conditioner blocks temperature fluctuations and reduces energy consumption by 30% compared to conventional devices. Perhaps the main advantage of such models air conditioners is their almost silent operation, which is very important for families with small children or for placement in the bedroom. Also a significant advantage of this type air conditioners is their low power consumption, which is important if a large number of equipment is connected at the same time in an apartment or house. Remote control, which are equipped with most models, make it easy and quick to carry out controlair conditioner.
Compliance rate: 7.47%
Fragments of the post text:
Installation, assembly air conditioners inexpensive The development of various technologies is now taking place just by leaps and bounds and it is worth recognizing the fact that the installation is really being carried out now air conditioners inexpensive and very fast. Mounting air conditioners it is inexpensively performed at a very high quality level - the price does not affect anything here, because mistakes in installation will lead to negative consequences and the company will certainly lose its face once and for all, and with it a huge number of potential customers. Please note that very often the installation air conditioners inexpensively performed under the influence of a large number of promotions, bonuses and discounts, and this is already quite incredible savings. It is simply paradoxical that against the background of the fact that the montage air conditioners is inexpensive and quickly implemented today, many people continue to ignore the possibility of installing this equipment. Pay attention only to the possibility of installation air conditioners in installments, which allows more and more people to make their lives more comfortable. It is important to note that manufacturers air conditioners are also not going to give up their positions at all. In turn, more and more different models air conditioners, among which it will be much easier to choose exactly what we really need and is suitable in terms of price, quality or appearance.
Compliance rate: 5.62%
Fragments of the post text:
Requirements to air conditioners- a guarantee of your comfort We all want our homes to be warm, comfortable, cozy at any time, and cool and fresh in the heat. Before purchasing such a device, you need to know in advance what the requirements for air conditioners are presented. TO air conditioners should be treated as essential household appliances and not as elements of prestige. To the most "ancient" air conditioners, intended for the house, we refer the so-called window frames. At work all air conditioners for home, three main modes are used, which allow you to cool and purify the air, reduce its humidity. Requirements to air conditioners include the ability to maintain a comfortable microclimate in the room. Not last place assigned to architectural and construction requirements, the possibility of remote management device.
Compliance rate: 4.86%
Fragments of the post text:
Depending on the temperature set from the remote remote control(DU) they support the so-called climate control. The difference, as well as the advantages, air conditioners inverter type consists in the possibility of variation, in other words - the ability to change the capacity of the performance of the air conditioner itself. First of all, it should be noted that thanks to its inverter management the fluctuation (drops) of temperature in the room is reduced, thereby maintaining a constant climate control. In addition, it should be noted that inverter air conditioners Compared to conventional ones, they consume 30% less electricity and have a lower noise level. Inverter control allows you to reach the set temperature about 30% faster than in the case of using conventional models.
Compliance rate: 4.69%
Fragments of the post text:
Cleaning products air conditioners The climate control system was designed to delight us with warmth or coolness for a long time. If the machine smells bad, it's time to apply an antibacterial agent to air conditioners... Antibacterial agent for air conditioners eliminates the cause of these ailments. It is not for nothing that it is recommended to thoroughly clean the device at least once a year using a professional chemical cleaning agent. air conditioners... More recently, a non-chemical innovative agent has appeared for air conditioners... By air it effective remedy for air conditioners will get inside the unit, and will "clean up" there on its own.
Compliance rate: 3.99%
Fragments of the post text:
In the technical documentation for the product, manufacturers of household air conditioners, with a reverse cycle, as a rule, indicate the temperature range within which the air conditioner can be operated. What can happen to air conditioner, if this limitation is neglected. Most of the modern air conditioners- these are models that have two modes of operation. Many buyers air conditioners worried about whether it can be operated in winter. In this the consumer will always be helped by highly qualified specialists in installation, maintenance. air conditioners and split - systems.
Wall split systems Samsung AQ09TSBN - operating and installation instructions
Wall split systems (air conditioners) Samsung AQ09TSBN General characteristics:
- Type - indoor unit
- Unit installation - wall-mounted
- Switched with the block - AQ09TSBX
- System - Heat pump
- Remote control
- Timer 24h
- Noise level (max./min.) - 32/24 dB
- Power supply - 220-240 V - 1 phase - 50 Hz
- Air consumption - 450 m3 / h
- Main modes - cooling / heating
- Cooling power - 2.8 kW
- Heating power - 2.9 kW
- Power consumption in cooling mode - 0.855 kW
- Power consumption in heating mode - 0.803 kW
- Auto mode
- Indoor unit split system
- Height - 285 mm
- Width - 820 mm
- Length - 210 mm
- Weight - 8 kg
- cooling -10? С ... + 43? С
- heating -15? С ... + 24? С
Samsung air conditioner remote control arh-1403 manual
For this, many Samsung air conditioners have a test mode. You can enter the test mode by pressing and holding the ON / OFF button on the indoor unit for five seconds. The air conditioner automatically adjusts the room temperature and air flow to the optimum level to reduce the humidity in the room based on the current temperature. The range of the beam of the infrared air conditioner control panel does not exceed 5-8 meters, moreover, bright lighting can interfere with the operation of air conditioner control panels at a distance of over 5 meters. Infrared air conditioner controllers are easy to use, but their field of application has limits. However, as technology is constantly being improved, even such a simple device is constantly overgrown with new functions. Operation with the air conditioner remote control - When using the air conditioner remote control, its transmitting part should be directed towards the indoor unit of the air conditioner. In the event of an unexpected power outage, the air conditioner control unit remembers the modes set from the remote control and automatically resumes the operation of the system in the same modes at the moment when the power supply appears again. When operating in dehydration (dehumidification) mode, the air flow is automatically set according to an optimization algorithm that reacts to the room temperature, so the room conditions remain healthy and comfortable even with high relative humidity. The remote control is suitable for the SAMSUNG series of air conditioners - we tested it in practice - everything works 100%.
In order to cope with error 21 (malfunction of the thermocouple that measures the air temperature at the inlet), it is necessary to disconnect the corresponding sensor from the board (the connector (connector) is designated on the diagram as CN43) and measure its resistance. Sleeping mode. 1. If you want to put the product into an energy-saving mode, for example at night, press the AUTOMATIC SLEEP BUTTON 2. The timer is programmed for 1 hour periods by pressing the AUTOMATIC SLEEP BUTTON from 1 to 7 times. However, in this case, the temperature value is not shown on the display of the remote controller; this mode does not allow you to adjust the room temperature. Moisture is removed from the indoor air intensively and uncontrollably. Infrared remotes are easy to use, but the control range does not exceed 5-8 meters. Analyzing the balance of these parameters, it cools or heats the air in the room.
To cancel the display of the code, hold down the ON TIMER CANCEL or OFF TIMER CANCEL button for 5 seconds. Note: This function is activated at the factory, but can be deactivated by pressing and holding the On / Off button for 6 seconds. To cancel sleep mode, press the SLEEP MODE AUTO button several times until the timer LED turns off. Dry mode keeps the air fresh in humid climates. The product will give sound signal twice and the indicator light (2) will flash 4 times. If there is a malfunction in the air conditioning system or the air conditioner is faulty, then when the command is turned on, the indicator lamps on the indoor units of the split systems begin to flash in a special way, signaling error codes. 2. Wired remotes transmit signals through special low-current thin wires. How to use the remote control for the RC UNI / AIRCO3 air conditioner Setting up the remote control if the model code of the air conditioner is known: Insert batteries. Operation mode Turn on the air conditioner by pressing the ON / OFF BUTTON - the air conditioner will beep Open the cover of the remote control and press the operation mode selection button. If the blocks are connected incorrectly, any diagnostics will give an incorrect result.
- Samsung Remote Control - Button Assignment Display Remote Control Battery Change Time If the batteries are low, this icon will appear on the remote control display.
- The remote control requires two 1.5V AAA batteries. Storing the remote control If you do not use the remote control for a long time, remove the batteries from the remote control and store it without them.
- Fan mode is useful for refreshing stale indoor air. Heat The air conditioner can heat your room.
- After turning on for heating, the air conditioner will start to supply warm air after 5
Manually adjusting the vertical airflow louver angle may damage the louver mechanism. Where can I buy a remote control device? At us, in the online store "VashPult", you can purchase a remote control from the air conditioner, the samsung manual will help you understand its functions. In the catalog posted on the site, you can select the desired model. We only offer original products. When a particular malfunction of the air conditioner is detected, the LEDs light up or flash in a certain sequence, which corresponds to the detected error. Activating this function will provide you with cleaner and healthier air. Testing. In test mode, the air conditioner operates in cooling mode at maximum fan speed regardless of the room temperature for 18 minutes, after which it resets the settings. You can buy a remote control for a samsung air conditioner with the AUTORESTART function, which allows you to remember the set mode on the equipment even after the power is turned off. An important function of the air conditioner is AUTORESTART. It cannot be set from the air conditioner control panel, but its presence greatly facilitates the operation of the air conditioning system. Stop pressing as soon as the desired fan speed appears on the screen display. 5. Mode of operation. Wipe the transmitter of the remote control and the receiver of the air conditioner regularly with a dry cloth. - Signaling can be difficult if the room contains fluorescent lights that are triggered by an interrupter. At an air temperature of +25 ° C, it should be 10 kOhm with an error of 3% (resistance values at other temperatures are given in the service manuals). If not, the sensor needs to be replaced. SLEEP mode - compliance with the parameters of comfort during sleep.
The AUTO mode maintains a temperature of 22-24 ° C, every half hour it compares the outside temperature with the temperature at the inlet to the indoor unit of the air conditioner and the set degrees. Press simultaneously and hold the "UP" and "DOWN" buttons for setting the temperature on the remote control. SLEEP mode after setting the desired temperature on the air conditioner control panel and receiving the SLEEP command, the split system provides set parameters... Wired remote control devices can work at any distance. Click the Auto Clean button. When the air conditioner is off, the Auto clean indicator appears on the indoor unit display and the Auto clean function is automatically activated.
There are five pairs in total (ten characters in total). Switching between code pairs is carried out with the "MODE" button. 1) Remove one battery from the remote control. It is interesting that 4-8 air conditioners can be controlled from one wired remote control. While holding these 2 buttons, insert the battery into place. Six zeros will appear on the remote. COOL mode - cooling up to 16-18 ° С (depends on the brand of the air conditioner). Consumers use this mode when it is hot outside, and you need to create a comfortable coolness in the room. As a rule, the setting of the universal remote control is performed by a service technician, but this can also be done by the consumer independently, since the remote control is completed detailed instructions... The air conditioner is now operating in / Good sleep / (Cooling) mode. - If you do not press the Set button within 10 seconds after pressing the / Good sleep / or Time Up or Time Down button, the air conditioner will return to its previous state. By the way, you will have to replace the board, even if the relay itself is faulty, since it is not supplied separately from the board. Today there are new items that are suitable for all brands of climate control devices. Each air conditioner model has its own code, in particular, for the Vivace series, which consists of four models, four different codes, depending on which specific air conditioner you are dealing with.
Let's take an example of one of such universal air conditioner control panels. When this function is enabled, the air conditioner operates in cooling mode with a very high fan speed, for fast and efficient cooling, the temperature is automatically set to 18 ° C for 30 minutes. To disable the function, press the Turbo button again. If you want to use the test mode, Press and hold the ON / OFF button for 3
5 seconds, then 1 beep (beep) will follow. to cancel this mode, press this button again. For the remote control to work with your air conditioner, you must enter the model code. This mode does not allow setting or maintaining the exact value of humidity. Using the Auto Clean Function The Auto clean function will prevent mold growth by removing moisture from the interior of the unit. If the air conditioner receives a command from the remote control during testing, it enters the command execution mode.
Program-download71: News
Hidalgo. [RESOLVED], Samsung AQ07XLN [RESOLVED] Schematic diagrams and service manuals General conditioners Electric. AL ._. EX. 0 Service manual AKIRA. nbn. eight.
Video: Air conditioner repair - filter cleaning. tried to reanimate the split according to your instructions, a signal from Tell me if there is a service code for the Samsung AQ07XLN / X air conditioner. Thank you in advance.
Detailed instructions for disassembling a split system. Sooner or later, any user of a domestic air conditioner. Tell me why there is a full-length foam strip in the drain tray of the split system Samsung (nine).
Samsung [Archive] - Fridge Forum
Split system Samsung AQ09TSBN / X - reviews I got a defective air conditioner Samsung (Samsung) Split system Samsung AQ07XLN ser. 3.75.
I have a mobile air conditioner BEKO-BKK-09C, when it is turned on, 141980 Mikhail (Moscow) 2012-06-29 22:21:49 Vacuum cleaner SAMSUNG vc-8716ht. We have a bosch benvenuto B20 coffee machine, the instruction, unfortunately, was lost. firmware code for split system Samsung AQ07XLN thanks in advance.
[Archive] Repair of Samsung air conditioners. Need help. I can’t go through · Has plugged in the AQ07XLN conder help me figure it out 24 TAB5X · Help me find a manual for troubleshooting a SAMSUNG air conditioner.
Air conditioner control panels infrared remote control wall-mounted wired remote controls for cassette channel.
Tell me where you can get instructions, it's not clear how to include it and how. kind; the firmware (unlock) code "Samsung AQ07XLN", everyone blinks. Could you help with the instruction for SAMSUNG air conditioner (pictured)?
Helios, most likely the firmware in the air conditioner has crashed. Here's what can help in your situation (please note that all of the below reference information and only you decide whether you will use it in order to fix the problem yourself): So, to revive your air conditioner, you must enter the firmware code using the remote control. Your model code: 25 02 57 03 40. The code is entered by two characters. There are five pairs of characters in total. Switching between pairs of codes is carried out with the "MODE" button. The course of your actions: 1) Remove one battery from the remote control. Press simultaneously and hold the "UP" and "DOWN" buttons for setting the temperature on the remote control. While holding these 2 buttons, insert the battery into place. The remote control will display two zeros with a triangle opposite the top symbol - "AUTO". Release the temperature setting buttons. 2) Enter the first pair of code. The "DOWN" button is responsible for changing the first digit. The "UP" button is responsible for changing the second digit. Each time you press the button, the number changes in a circle in the sequence 0-1-2-3-4-5-6-7-8-9-A-b-C-d-E-F. 3) Using the "MODE" button select the second pair of characters - a triangle opposite the second from the top character - "Cooling". 4) Enter the second pair of code. The "DOWN" button is responsible for changing the first digit. The "UP" button is responsible for changing the second digit. Each time you press the button, the number changes in a circle in the sequence 0-1-2-3-4-5-6-7-8-9-A-b-C-d-E-F. 5) Do the same by analogy for the remaining three pairs of signs. 6) Pressing the "MODE" button make sure that all five code pairs are correct (by switching). 7) Directing the remote control with the code to the indoor unit, press the "ON / OFF" button. The indoor unit will play a small sound to indicate that it has accepted the new firmware code of the board. Pull out and insert the batteries back into the remote control (without pressing any buttons) to switch it to normal operation. For owners of a model with a 12-digit firmware code, the algorithm is somewhat different (the list of codes for most models is given below): 1) Remove one battery from the remote control. Press simultaneously and hold the "UP" and "DOWN" buttons for setting the temperature on the remote control. While holding these 2 buttons, insert the battery into place. Six zeros will appear on the remote. Release the temperature setting buttons. 2) The first half of the code starts with the digit "0". Switching between the first and second half of the code is carried out with the "MODE" button. Select the first digit - "0". 3) Pressing the buttons indicated in the figure, enter the first half of the code (six digits, the first of which is zero). Each button is responsible for changing its code digit. Each time you press the button, the number changes in a circle in the sequence 0-1-2-3-4-5-6-7-8-9-A-b-C-d-E-F. 4) The second half of the code begins with the number "1". Switching between the first and second half of the code is carried out with the "MODE" button. Select the first digit - "1". 5) Pressing the buttons indicated in the figure, enter the second half of the code (six digits, the first of which is one). The procedure is the same as in clause 2. 6) Pressing the "MODE" button make sure that the first and second half of the code are correct (by switching). 7) Directing the remote control with the code to the indoor unit, press the "ON / OFF" button. The indoor unit will play a melodic sound, indicating that it has received the new board firmware code. Pull out and insert the batteries back into the remote control (without pressing any buttons) to switch it to normal mode work. Codes for all models: Model 1 Model 2 Reference 1 AQ07A5ME 014A25-1700b7 AQ09A1ME 016A25-1700d9 AQ09A5ME 016A25-1700d9 AQ12A9ME 017d25-17021d AQ18A9RE 097417-1A00Fb AQT24A1RE 094617-1A023F AQT24A5RE 094617-1A023F SC05ZA8 040000-1740A6 SH05ZA8 006825-1700d9 SH07ZA8 004825- 170,067 SH07ZPGA 026065-17022E SH07ZS8 026064-1720Fb SH09VCD 007d08-1010Fb SH09ZA8 006825-1700d9 SH09ZK8 027064-17221d SH09ZPGA 026566-170340 SH 09ZS2 025266-17A23F SH09ZS8 027064-17221d SH12VCD 007315-10123F SH12ZAB 007227-17023F SH12ZKG 066025-172362 SH12ZPGA 067066-170362 SH12ZS4 066065-17A351 SH12ZSG 066025-172362 SH18ZAOD 086417-1A021d SH18ZPOA 086115-1d0351 SH18ZSOA 085115-1D2340 SH24TA6D 086314-1A023F SH24TP6A 085416-1d0384 SH30ZC2 0E0000-1d020A SH12ZSG D66025-172362 SH09ZS8 027064-17221d SH07ZS8 026064-1720Fb SH12ZPG 067066-170362 SH09ZPG 026,566 -170340 SH07ZPG 026065-17022E AS09A3ME SC09ZA3 / A 010000-1700d9 AS07A3ME SC07ZA3 / A 010000-1700b7 AS09A4ME SC09ZA4 / A 000000-1700d9 AS07A4ME SC07ZAb4 / A 12ZA1 / A 010000-17021d AS09A1ME SC09ZA1 / A 010000-1700d9 AS07A1ME SC07ZA1 / A 010000-1700b7 AS12A2ME SC12ZA2 / A 000000-17021d AS09A2ME SC09ZA2 / A 000000-1700d9 AS07A2ME SC07ZA2 / A 000000-1700b7 AQV12Y6ME 007510-10723F AQV09Y6ME 007500-1070Fb AQV12A2ME SH12VA2 005212-10123F AQV09A2ME SH09VA2 006500-1010FB AQV12A1ME SH12VA1 015212-10123F AQV09A1ME SH09VA1 016500-1010FB SH12VCD 007315-10123F SH09VCD 007d08-1010Fb AD18B1 (B2) E09 MH18ZA1 (A2) -09 016223-1000EA AD19B1 (B2) E07 MH19ZA1 (A2) -09 015553-100B7 AD19B1 (B2) E12 MH19ZA1 (A2) -12 015553-10023F AD24B1 (B2) E12 MH24ZA1 (A2) -12 017553-10021d AD26B1 (B2) E12 MH26ZA1 (A2) -12 - AD26B1 (B2) E0 MH26ZA1 (A2) -07 - AQT24A1 (2) RE 094617-1A023F SH24TA1 094617-1A023F AQT24A2RE 084617-1A023F AQT24A2RB 084617-1A023F AST24A1RE 090000-1A023F SC24TAF AST24A1RE 090000-1A023F SC24TAF AST24A1RE 090000-1A023F SC24TAF AST24A1F090000-1A023F SC24TAF AST24A1RE 090000-1A023F SC24TAF AST24A1A023F 1A00FB AQT18A2RE 087417-1A00FB AQT18A2RB 087417-1A00FB AQ18A1RE 094417-1A021D SH18ZA1 094417-1A021D AQ18A2RE 084417-1A021D AST18A1 RE 090000-1A00FB SC18TA1 090000-1A00FB AST18A2RE 080000-1A00FB AST18A2RB 080000-1A00FB AS18A1RE 090000-1A021D SC18ZA1 090000-1A021D AS18A2RE 0800001A021D SH12ZPOB 085115-1d0351 AQ18P0GBA 085417-1d0340 AQ18P0GEA 08511-51d0351 AQT18P0GBA 0854d7-1d0340 AQT18P0GEA 0854d7-1d0340 SH24ZP6B 0872d6-1d0362 AQ24P6GBA 087417-1d0362 AQ24P6GEA 0872d6-1d0362 AQT24P6GBA 085417-1d0362 AQT24P6GEA 085417-1d0362 SH24TS6 085416-1d2362 AQT24S6GB 085417-1d2362 AQT24S6GE 085416-1d2362 AQ24S6GB 0852d5-1d2373 SH18ZS0 085115-1d2340 AQT18S0GB 085417-1d223F AQT18S0GE 085417-1d2340 AQ18SOGB 085115-1d223F AQ18SOGE 085,115 -1d2340 SH05ZZ8 005025-17021d SH07ZZ8 005024-170360 SC05ZZ8 000000-17021d AS05Z1AZD 000000-17021d AS07Z1AZD 000000-17021d SH24TP6 (A) 085416-1d0384 AQT24P6GB 085417-1d0384 AQT24P6GE 085416-1d0384 AQ24P6GB 0852d5-1d0395 SH18ZPO (A) 086115-1d0351 AQT18P0GB 085417 -1d0351 AQT18P0GE 085417-1d0362 AQ18P0GB 085115-1d0351 AQ18P0GE 086115-1d0351 SH24TS6 085416-1d2362 AQT24S6GB 085417-1d2362 AQT24S6GE 085416-1d2 362 AQ24S6GB 0852d5-1d2373 SH18ZS0 085115-1d2340 AQT18SOGB 085417-1d223F AQT18S0GE 085417-1d2340 AQ18S0GB 085115-1d223F AQ18S0GE 085115-1d2340 AQ12-17026 * 6MB A17777 * 5ME SH09Z * 5 016A25-1700d9 AQ * 6ME SH09Z * 6 006A25-1700d9 AQ09 * 5MED SH09Z * 5D 016024-1700EA AQ07 * 5MED SH07Z * 5D 006 024-1700EA AQ07 * 5ME SH07Z * 6 006024 004A25-1700b7 AQ07 * 6ME SH07Z * 6 004A25-1700b7 AQ09 * 7ME SH09Z * 7 016825-1700d9 AQ09 * 8ME SH09Z * 8 006825-1700d9 AQ07 * 7ME SH07Z * 7 014825 * 867 * 867 AQ0-17Q 9ME SH12Z * 9 017d25-17021d AQ12 * 0ME SH127 * 0 007d25-17021d AQ12 * A (B) ME SH12Z * A (B) X 007227-17023F SH30ZC1 0F5495-1d020A SH30ZC2 02 0E54951d020 40 SWA 25 57-ZWH / 03 SH12AWH AQ12WHWE 25 02 57 03 40 SH09AWH 25 02 57 00 08 SH09ZWH / AQ09WHWE KFR-25G / SWA 25 02 57 00 Fb SH07ZP2 / SH07ZP2A AQ07P2GE 024567-17021d SH09ZPA 06 SH09ZP2GE0-1706 66170362 AQT12P4GB 0670E6-170362 AQT12P4GE 0680E6-170351 SH07ZS2 SH07ZS2A 024567-17A200 SH09ZS2 025266-17A23F SH09ZS2A AQ09S2GE 025365-17A23F SH12ZS4 066065-17A351 SH12ZS4A AQ12S4GE 067066-17A351 AQT12S4GB AQT12S4GE 0670E6-17A351 AQ12 * 5MC AQ12 * 6MC 017725-17021d AQ09 * 5MA AQ09 * 6MA 016A25-1700d9 AQ18 * 5RC AQ18 * 6RC 094415-15021d AQ24 * 1RC AQ24 * 2RC 097617-1A023F AS12 * 5MC AS12 * 6MC 010000-17021F AS09 * 5MA AS09 * 6MA 010000-1700d9 AS07 * 5MA0000-1700b7MA AS18 * 5RC AS18 * 6RC 090000-15021d AS24 * 1RC AS24 * 2RC 090000-1A0340 SH07ZK8 026064-1720F6 AQ12 * 6MC 007725-17021d AQ09 * 6MA 006A25-1700d9 AQ18 * 6RC 084415-15021d AQ24A 623MC * AS112 -17021F AS09 * 6MA 000000-1700d9 AS07 * 6MA 000000-1700b7 AS18 * 6RC 080000-15021d AS24 * 2RC 080000-1A0340 MH18ZC1-09 016223-100EA MH18ZC2-09 006223-1000EA MH19ZC1-07 015553-1000Cb7 MH557 MH19ZC1-07 015553-10023F MH19ZC2-12 005553-100023F MH24ZC1-12 017553-10021d MH24ZC2-12 007553-10021d MH26ZC1-07 011553-1000d9
Irina Viktorovna. 07/26/2016 at 18:16
Irina Viktorovna. 09/15/2016 at 23:06
Hello, we offer you the services of comprehensive promotion of your site, you can find more information on our services at the link http://www.anacron.ru/ Sorry for your concern.
Remotes for Samsung air conditioners
For the site to work properly, you need to enable them!
Remotes for Samsung air conditionersModern and convenient remotes for Samsung air conditioners! You can purchase the model you are interested in in our online store.
DK remotes are designed to control the air conditioner remotely. Such a system simplifies life and contributes to a person's comfortable state.
DK remotes are divided into 2 types - wired and infrared. Infrared remotes are used for ceiling-mounted and wall-mounted air conditioners. They are also used in window models of cassette air conditioning systems.
Samsung DK remote performs the following commands:
1. HEAT - room heating. Carries out heating and air filtration.
2. COOL - room cooling, as well as air dehumidification and filtration.
3. DRY - air is dehumidified, filtered and slightly cooled.
4. FAN - ventilation of the room. Filtration and constant air circulation without temperature changes. The fan rotates continuously.
5. AVTO - the air conditioner automatically selects the heating or cooling function and maintains the temperature from 22 to 24 degrees.
The infrared remote control is equipped with commands that perform self-diagnostics, which allows you to quickly eliminate the malfunction.
Instructions for Samsung air conditioners, split systems, remotes
Fresh air admixture
Winter kit for air conditioner price instruction reviews do-it-yourself photo what is a winter start device installed
The formula for calculating the power of the air conditioner
Air conditioner Daikin ATY35D. The timer allows you to program the activation and deactivation of the air conditioner.
Do-it-yourself air conditioner installation - features of air conditioners, installation of outdoor and indoor units, connection to
Installing the air conditioner yourself or is it possible to install the air conditioner yourself, how to install the air conditioner yourself
Air conditioner Daikin ATY20D. The air conditioner can be equipped with a low temperature
We choose the quietest air conditioners.
Air conditioner Daikin FT25J. Multi-stage air purification with photocatalytic
What the air conditioner can do. Lots of information about air conditioners, split systems, air purifier.-..-
Air conditioner in Podolsk. Air conditioner and split-system device, compressor device (internal, external, externally 
Air conditioners with fresh air supply
Split-Split - how to properly care for an air conditioner with a split system
How to choose an air conditioner for an apartment or a room - selection of modern air conditioners for the office
Air conditioner Daikin FAQ71B / RR71BV / W. Controlled as a local console
How to choose an air conditioner or what you need to know about air conditioners
Mobile air conditioner without duct
The main types of air conditioners
Air conditioner noise level
To what minimum temperature can the air be cooled using a split system?
How to choose an air conditioner
Conditioners. Types of characteristics comparison of air conditioners
Types of air conditioners, household and semi-industrial air conditioners, mobile and floor air conditioners, wall and duct with 
Health. Are air conditioners threatening him?
Air conditioner device - how the air conditioner works
Air conditioners catalog. How to choose an air conditioner? Power calculation. Types and functions of air conditioners.
The most important thing is the weather in the house. Air conditioners will create the weather - that's their purpose
Practical work No. 1 Topic "Operations with files and folders" in OS Windows Purpose of work
Thesis: Improving the efficiency of security services in hotels and restaurants
9. Regime of the day in the children's health camp
Popular on the channel:
Fault codes and errors on split systems Samsung
There are five mistakes in total. A malfunction of the room temperature sensor makes itself felt by an error with code 21, the E1-21-E1 indicator flashes on the display, a malfunction of the heat exchanger temperature sensor - by error 22, a malfunction of the indoor unit fan - by error 54, a malfunction of the processor air conditioner.
more
Disposal
This product is made of complex materials that must not be disposed of with ordinary waste. Some of them you can use Find out. re-how to properly dispose of items in your area.
Name of each part
block External.
Name of each part
Internal and external blocks
1 - Decorative panel of the indoor unit.
2 - product This removes air on the side surfaces.
3 - air Is taken from the top to the heat exchanger.
4 - At the outdoor unit, a fence is carried out on the back and side surfaces.
5 - Outlet after contact air with the heat exchanger in front.
Remember that this model is plugged into a reinforced outlet and consumes more energy than a conventional electrical appliance. Therefore, you can not connect it to extension cords, sockets of insufficient How.
nominal and for most consoles, the requirements for the power supply to the elements are the same - they must be of the same type, not rechargeable, correctly installed.
Selecting work modes
Turning on the device, which is already connected to the network, you can use the remote control to select an interesting mode for you.
If you wish, you can fully automate the work of the device by turning on the automatic mode. specify the upper and lower temperature limits are enough and you can forget about other actions. The device will automatically turn on the cooling when the temperature rises and vice versa.
If you choose a separate mode, it's easy to do - in summer, cooling mode is enough, during cold time - heating.
Dehumidification mode can be used separately. In this case, the device works in such a way as to reduce the humidity, but not to influence the temperature.
When you select the simple ventilation mode, ventilation of the air in the room is maintained.
Advanced modes and settings
The "Neoplasma" filter perfectly removes odors from the air, along with other substances. mode Therefore, the "fan" is excellent for cleaning air in the room.
Using the timer, you can set the time when the device will automatically turn on and the Mode.
self-diagnosis turns off is convenient because you can find out about the state of the device without resorting to third-party For.
It has a self-cleaning function to help combat mold and bacteria. The device independently dries the internal cavity of the block. This does not give microorganisms to.
to multiply work at night there is a "Thanks" mode. sleep inverter type of work the device is very quiet. And in this mode it is even quieter.
Tips Useful
If you plan to cool the room, then you do not need to overdo it - excess cold will not be good for your health and you will waste a lot of energy.
Do not forget to check the condition of windows and doors - if cold air leaves the room, then the work becomes much more complicated.
At the beginning of work, it is worth using the enhanced operation of the fan in order to cool the room faster.
We must not forget about airing the room. Oxygen fasting can harm your health.
Air Conditioner Cleaning
All actions must be performed when the air conditioner is disconnected from the mains. Disconnect the plug with dry hands.
Dry all washed components in the shade.
Do not use solvents, abrasives, gasoline, hot water, otherwise you will ruin the appearance of the outer plastic.
If it seemed to you that there is a malfunction
If the device does not work, check it if the timer could turn off. Or it is not just connected to the network.
If the air conditioner is badly needed, then the cooling check a number of points. It must be tuned to the correct mode and sufficient power. It is possible that the windows and doors in If are open. there are a lot of people in the room or the heating device is operating, the air conditioner will operate the system.
worse, protecting the device from frequent restarts will block the ability to turn on the air conditioner within 3 minutes immediately after turning it off.
If fog comes out of the air conditioner (white smoke), remember that cold air, in contact with humid air, causes condensation to appear.
Also, remember that cold parts of the air conditioner will cause the appearance of condensation water from the air conditioner.
warming up When dwelling, the outdoor unit cools down and may freeze up. Therefore, the device must periodically stop thawing ice, which can damage the device.
In case of any problems with the remote control, first of all, check if the batteries are in order, if they are installed correctly, if the button on the remote control is jammed.
A crackling sound can accompany the device during Sound.
heating splash, dripping may occur due to condensation movement, refrigerant.
If there is a smell from the indoor unit, it may be time to smell it Also. cleaning, the smell may belong to blooming wallpaper, wall, carpet.
When the air conditioner is taken out of operation for a long time
Turn on the Next mode. self-cleaning, turn off the device and do not forget to remove the sockets from the plug and the batteries from the remote control.
Before after turning on the downtime, you need to check that both units are not clogged with foreign objects. Connect the mains to the device. Ground. Then install the proper batteries in the remote control and use the air conditioner.
location Choice of installation
It is not allowed to place the air conditioner in places where there may be machine fuel, substance oil, hydrogen sulphide in the air. The outdoor unit makes noise during operation and may interfere with people. In addition, when choosing a place for the air conditioner, it is necessary to provide for where you will drain the condensate.
Precautions Measures
Please note that the device must be connected to a socket of sufficient power, otherwise there is a risk of fire or its melting.
It is unacceptable to use Connect.
Extension cords and unplug the appliance should never be dry.
Do not place heavy, hot or other wires on top of power items with your hands.
It is not allowed to place objects (especially with water) on both air conditioner units.
Condensation may drip from the appliance - do not place other appliances or furniture under it.
Do not overload the device - disconnect first from the remote control, and then remove the sockets from the plug.
Never stick your fingers into the air conditioner, it is dangerous.
Do not expose yourself or others to direct, prolonged exposure to cold air.
Complete heating termination and cooling may be due to refrigerant leakage.
The smell of burning or strange time during the sounds of operation should alert you - disconnect the device from the mains. Call specialists to assess the situation.
Table of contents:
Disposal
Part name of each
modes Choice of work
your Air conditioner cleaning
If you think there is something wrong
If the air conditioner will not be used for a long time
Place of installation and work wiring
Precautionary measures
Disposal
This product is made of complex materials that are unacceptable with ordinary waste. Some of them can be reused. Find out how to properly dispose of such items in your area.
Name of each External
parts block.
Name of each part
A unique feature of the indoor unit of this air conditioner is that the front panel of the indoor unit allows you to place it on images and change them.
1 - Button to disable / enable work.
2 - Selection of the operating mode.
3 - desired temperature setting.
4 - Selecting the power of the air Start.
5 - flow of powerful heating / cooling mode (will turn on pressing one of the indicated modes and the fan on the Button).
6 - maximum for vertical position control. Turn on.
7 - dampers / timer off.
8 - Time setting (programming with timer).
9 - Activation / deactivation of work Installation.
10 - timer of the "Sleep" mode.
11 - Enabling the "Display" mode.
12 - Ventilation of the room temperature.
13 - Enabling / disabling the plasma filter.
14 - Selecting the horizontal direction of travel Reset.
15 - air parameters.
16 - Toggle keyboard control - selection for the function marked in blue.
17 - functions Start autovacuum.
18 - Heater operation control (if there is one).
19 - Adjust the brightness of the display.
Before Preparation Getting Started
Make sure the device is plugged into a separate outlet and grounded. items Install power supply to the remote control. Set the time. so that, Check foreign objects do not interfere with the movement of the outdoor and indoor units around the air.
After setting the power supply to the remote control, you must set the current time. To do this, press the button then, RESET specify the time and press the DISABLE / ENABLE button. After that, you need to press to make sure 2F and the button that a similar inscription is lit on Next. screen, pressing the time setting button, we set the current time. Then press the SET / CANCEL button on TIMER.
Mode selection By pressing
work the power button on the remote control, turn on Next. air conditioner by pressing the mode selection button you can select the mode you need now Sequentially. work by pressing it you will select the following Cooling (modes-Auto-selection-Dry-Heating). By choosing the mode you need, you can set the required temperature. for Heating mode selection is possible in the range of 16-30, cooling for 18-30 degrees.
After that, you can set the fan operating mode you want from several: (CHAOS feeling of a light breeze) and four constant modes from weak to maximum power.
Working in dehumidification (dehydration) mode, the air conditioner reduces the humidity of the air level. The level of the desired temperature cannot be set, since the device independently chooses, taking into account its current selection. In any case, the air conditioner operates in such a way as to reduce the minimum humidity to affect the temperature.
In contrast to the Cooling and Heating modes, where the air conditioner only cools heats or, when the Auto select mode is selected, you can specify the desired temperature range and when the temperature drops, the air conditioner will turn on the mode when the temperature rises, and when the Heating temperature rises, on the contrary, cool the room into the air.
Additional modes and settings
Fast heating / cooling mode. When the room temperature is too high or vice versa, it is recommended to first turn on the air conditioner at maximum power. After 30 minutes it turns on (for cooling and 60 works with maximum ventilation and heat dissipation.
Automatic restart function - activates the air conditioner in the same mode in which it worked before the emergency power supply was turned off.
For maximum air cleaning, there is a Plasma filter. It can be started in any operating mode of the air conditioner by pressing the Plasma button on the remote control.
“Self-cleaning” function - the process starts the removal of moisture from the internal cavities, it is necessary for the air conditioner after operation in the modes of dehumidification and cooling.
The "Energy Saving" function allows the device to switch to an economical mode of operation, during which it is quieter and consumes less energy.
Forced mode - if there is no remote control, you can turn on the air conditioner by pressing the button located on the indoor unit. By successively pressing it, you can turn on the cooling mode and turn off the air conditioner.
Startup Check. Timer is the correct time set on the remote control. by pressing the remote control button to start the second function (2F) and turn on the timer by pressing ON / OFF TIMER. Set the operation time of the timer using the setting buttons, forget. Not time, that all the time while you control the air conditioner using the remote control, the reception window, the remote control and commands must be within sight.
deactivate To timer: check that the 2F button is inactive and press the TIMER CANCEL button. Then the timer image on the display and the air conditioner should go out.
ADVICE:
... Do not overcool the room. harmful This is for health and unnecessarily increases electricity consumption.
... Close curtains or blinds while the air conditioner is operating. Keep the sun out of the light with the air conditioner running.
... Control the direction of the vertical flap so that the air temperature in the room is evenly distributed.
... Keep doors and windows tightly closed. Otherwise, the cold air will leave the room.
... Clean the air filter regularly. A clogged filter reduces air movement and increases energy consumption.
... Remember to ventilate the room periodically. During operation, the air of the air conditioner is not renewed as during ventilation, therefore, it is necessary to monitor this additionally.
... To cool the room quickly at the beginning of work, use the fan speed increased with the mode.
Cleaning your air conditioner
Choose a solid foundation on which to stand. Remember to unplug the plug before starting the cleaning. Do not use water of 40 degrees hotter, gasoline, abrasive detergents - this can damage the appearance of the plastic.
There are air filters behind the front panel. They must be cleaned at the time of and must be checked once in order. a week to remove dirt, you can use those in a vacuum cleaner in cases where it can be removed poorly, wash the filter in warm water with a liquid addition of detergent. After washing, the filters must be dried in the shade (not on Filters).
The PLASMA sun must be checked at least once every three months. Cleaning can be done with a vacuum cleaner, or washed with water. They cannot be dried in the sun either. Do not touch this filter for the first 10 seconds after turning off the air conditioner.
Deodorizing filters must be removed, dried in the sun for 2 hours and replaced.
Periodically inspect the external air conditioner unit and, if contamination appears, remove it for which you can call an employee of the corresponding company.
If it seems to you that there is a problem
The air conditioner does not work. Check if it is connected to the mains power, if the circuit breaker is not blown. Also, it is possible that there is no power in the network or too high voltage (in the second case, the protection of the air conditioner will work)
The air conditioner does not cool properly. so that there are no obstructions in the air flow between the outdoor and indoor units. The air filter must be clean. If the temperature of the air conditioner is too high, it becomes less efficient. check the same So that the windows and doors are closed. The temperature may not be set correctly. There may be a heat source in the room.
ALWAYS contact the service center if:
... there was a strong smell, burning noise at work. Unplug and unplug the device immediately;
... the power cord is plug or hot, you can see its damage;
... self-test startup, a malfunction code appears;
... water leaks from the indoor unit;
... detected operation in circuit breaker malfunctions.
If the air conditioner will not be used for a long time
At the end of the season, the air conditioner must be prepared for shutdown. To produce:
... why cleaning filters;
... turn on the warm-up mode for 1-2 hours to completely dry the internal block;
... turn off the air conditioner using the remote control;
... remove the elements from the remote control;
... disconnect the plug from the mains supply.
Before turning on after a long time Check.
... downtime, so that there are no obstacles to air movement near the outdoor and indoor units;
... insert the batteries into the remote control;
... set the time;
... Connect the plug to the mains.
Installation site and wiring Installation
the operation of the air conditioner must be performed by certified Verify. specialists, that in the place of the proposed installation there will be no obstacles for the movement of air, the noise of the external operation of the unit will not interfere with the living, there is also an opportunity to drain condensate from the external Measure nearby.
precautionary unit
Use a mains plug and a grounding type socket. Do not plug the air conditioner into an outlet with a lower rating. Do not use an extension cord - connect directly to use. Damaged plug and power cord. mains power cord and plug should be handled with dry hands.
Do not stand on your own or place heavy or hard objects on the power cord.
It is forbidden to disassemble, modify, repair the device yourself. For any repair work, you need to invite a specialist.
Make sure the racks are intact and in good condition for mounting. Reliable fixation of the outer block must be ensured to prevent it from falling.
Do not place objects on the outside and inside blocks, especially with water (for example, water from a vase).
Do not insert fingers or any other technological objects into the openings of the air conditioner. The fan runs at high speeds, which can lead to receiving If.
In case of injury, the air conditioner stops cooling or it warms up, it may indicate refrigerant leakage. In this case, it is necessary to call the repair specialists.
Do not stand in the way of the cold air stream, it can damage your health.
Split system installation | Air conditioning
What you need to know about installing a split system? The air conditioner works to increase the required temperature and humidity in the room. By ventilating the air, the air conditioner cleans it by passing a weightless stream through special filters. Let's talk about installing the most advanced type of air conditioning system.
more
Instructions: installation of a split system, video installation instructions
Installation of air conditioners. Choice. Installation of internal. Video tutorial on installation of split systems and. Additional charge of refrigerant. Installation of split systems, the whole truth about the installation of air conditioners. Instruction. Dear Customer, Thank you for choosing our air conditioner. Before installation is necessary.
more
Types of air conditioners - cassette and channel air conditioners, wall split systems and multi split systems, air conditioners
Split systems - consisting of two units (wall, duct, cassette and other types of air conditioners). The split-system air conditioner is divided into two blocks - external and internal, which are interconnected by an electric cable and copper pipes.
more
Does the air conditioner work in winter conditions?
This question arises most often when there is a need for air conditioning of server rooms, equipment rooms, computer rooms, etc. those. premises with big amount heat-generating equipment, where cooling of the room is required regardless of the season.
more
Girls, we want to buy and install a split. But here's what I found According to Art. 25 ZhK RF, installation of electrical equipment, including an air conditioner (washing machine, boiler, etc.), refers to the reconstruction of the apartment. And in accordance with Art. 26 of the RF LC should be made exclusively by agreement.
more
Do-it-yourself split system installation. Split system wiring and wiring. Air conditioner operation 
Description of functions and modes of Mitsubishi Electric air conditioners
Functions and modes of Mitsubishi Electric air conditioners 1. Saving energy consumption Control of "perceived temperature" I SEE - an infrared sensor that scans the temperature at the floor surface in a segment of 150 degrees, and the control system can calculate the temperature perceived by a person. Trad.
more
What you need to know about installing a split system. How to install climatic equipment in.
What you need to know about installing a split system. How to install climatic equipment at home This is the overseas word "Air Conditioning". The word "air conditioner" has taken root only in our country. This is actually a piece of the phrase air-condition, which translated from English means "state.
more
A few words about air conditioners. User manual. A brief introduction to climatic.
A few words about air conditioners. User manual. Brief acquaintance with climatic equipment Advantages of the option with the use of split systems: relatively low installation costs and short installation time Window air conditioner - the most "traditional" type of air conditioner.
more
Basic knowledge of the air conditioner (Details about air conditioners, how the air conditioner works)
Air Conditioning - From History to Present
Man suffered from the unbearable heat even in the distant past. Our ancestors had to resort to elementary methods of protection from the heat. Ancient people simply took refuge in caves. In later times, representatives of the noble and wealthy families sought to surround their luxurious castles with parks and soors.
more
Where to install the air conditioner correctly in the apartment. General rules to install the air conditioner
The name "split-system" speaks for itself: split in English means "to split". This air conditioner is divided into two blocks - internal and external. The most large and noisy parts are enclosed in an external block, which is installed outside the room, and a lightweight, modern design block is placed inside.
more
Wall split systems
Wall-mounted split systems This type of equipment includes an indoor wall and outdoor unit. The service area of such systems is from 15 to 100 sq.m. most often they are used in apartments (room, living room, kitchen, nursery), country houses.
more
Office air conditioner
Or what are office air conditioners and how to choose a model of air conditioner for the office If you are thinking how to create a comfortable temperature in an office space, start by determining the required power of the air conditioner. It's easy to do it yourself. The formula for calculating the air condition.
more
Questions about split systems in Rostov.
Split systems in Rostov Questions about split systems in Rostov. Split system dripping? Very often, in service center VIMTECH (site "Split systems in Rostov") worried customers call with the following questions: Why is it dripping from the indoor unit into the room? What to do if the water is split.
more
Split system air conditioners Tropic. Firms and brands of manufacturers of air conditioners
Split system air conditioners Tropic. Firms and brands of air conditioner manufacturers TROPIK air conditioners of the "split-system" type are split-type devices in which the indoor unit is installed indoors, and the outdoor unit is installed outside, for example, in the open air. These air conditioners are n.
more
Fresh air cannot be replaced with air conditioning
A person needs fresh, oxygenated air for life. And it is impossible to replace it with anything - neither tasty food, nor money, nor the pleasant coolness of an air conditioner. It is so invented by nature. At the beginning of the 19th century, American physician John Gorier created the first cooling apparatus.
more
Is it possible to use an air conditioner (split system) with a heating function when it is -20 outside the window.
Rat, Where there are powerful servers (easily 50-100 kW in total), you have to cool the room even in winter. This is true. But usually for such cases, cooling is used, as it is fashionable to call it, "free cooling" - a natural transition of heat from a high level to a lower one, since there is no reason to waste.
more
Sanya 86, how did you get it like that? I was also refueled today because it stopped cold, I don't know how long it will be enough, but as they explained to me, the device that refills creates a vaukum in the circuit for 10 minutes and monitors the readings of the sensors, if there is a leak somewhere, then it will manifest itself and then it simply does not.
more
A small mobile air conditioner is perfect for maintaining a microclimate in a room up to 45 m2. The power of some with
The catalog of the ClimatStyle company contains air conditioners from the world's leading manufacturers of climatic equipment. All devices have been tested and have quality certificates. Mobile air conditioners A mobile air conditioner is a compact and easy-to-use device.
more
Air conditioner Ventilation Poltava 69-38-40
1 EUROFAN СSU-07HHAA air conditioner Manufacturer: MIDEA plant (China), ECO 210 340 class 2 EUROFAN СSU-09HHAA air conditioner Manufacturer: MIDEA plant (China), ECO class 220 365 3 EUROFAN СSU-12HHAA air conditioner Manufacturer: MIDEA plant (China), class ECO 260 415 4 Air conditioner EUROFAN СSU-18HH.
more
What types of air conditioners are there and what is the difference between them?
There are the following main types of air conditioning equipment: 1. Mobile or mobile floor air conditioners are interesting because they do not require special investment of time, materials and money for their installation indoors. They are optimal for a tenant of residential or commercial space, since n.
more
How to properly dismantle an air conditioner (split system), or how to dismantle an air conditioner. Situations often arise
Home / Articles Articles Show all entries How to properly dismantle an air conditioner (split system), or how to dismantle an air conditioner. Situations often arise, for example, moving, redevelopment, etc. when needed.
more
An air conditioner is a special apparatus that moves and also processes air in air conditioning systems. Con
Air conditioners An air conditioner is a special apparatus that moves and processes air in air conditioning systems. The air conditioner must regulate the freshness of the air in the room, the purity of this air, its humidity, as well as the speed of air movement around the room. In our.
more
Thesis: Analysis of the competitiveness-style of tea brands based on the study of its assortment
Glossary of terms Air conditioner. A system that controls temperature, humidity and air circulation. Accumulator - dehumidifier. A container that contains filters, a desiccant to capture and retain moisture. functionally similar to the receiver - it will dry.
more
Thesis: Automation of warehouse activities of the company OJSC "Wimm-Bill-Dann Foods"
Types of office air conditioners
Choosing an air conditioner for an office According to modern requirements, in order to maintain ideal comfortable conditions in offices, air purified from mineral and organic dust should contain about 21% oxygen and no more than 0.3% carbon dioxide. Its temperature should be in the range of 20-24 ° C, rel.
more
Choosing an air conditioner for the office.
17 Jan 2009 According to modern requirements, in order to maintain ideal comfortable conditions in offices, air purified from mineral and organic dust must contain about 21% oxygen and no more than 0.3% carbon dioxide. Its temperature should be in the range of 20-24 ° C, relative humidity.
more
Some useful tips for those wishing to install an air conditioner
Several useful tips for those wishing to install an air conditioner at their place If you decide to create normal conditions for work and rest and install an air conditioner for this, read this article to the end. It is useful to know what types of air conditioners are available in general. Window type. This is a normal air conditioner.
more
Instruction for the buyer of the air conditioner. What is harmful or useful for an air conditioner, air purifier or.
Instruction for the buyer of the air conditioner. Why an air conditioner, an air purifier or a humidifier is harmful or useful I. Choosing a company - seller It should be noted that the vast majority of air conditioning companies value their reputation, but from time to time firms appear and immediately disappear.
more
Types of air conditioners. Selection and main characteristics of air conditioners.
Types of air conditioners. Selection and main characteristics of air conditioners. Window air conditioner is a monoblock air conditioner that is mounted in a window opening or a thin wall. Compared to split-systems, a window air conditioner has a number of disadvantages, including a higher noise level and no.
more
Problems - the air conditioner does not work, makes noise, freezes.
Questions: Why is the air conditioner making noise, etc. Questions from our dear customers: How to install the air conditioner correctly? Where to install the air conditioner correctly? How much freon do you need for an air conditioner? How to clean a split system? Why can't the air conditioner be turned on in winter? When you can't turn on the air conditioner
more
Almost everyone knows the name of the company "Samsung", it is not surprising, because it is a conscientious manufacturer and world leader in the production of not only split systems, but also many other household appliances and electronics. Samsung's development history began in 1938. The firm was founded by a man named Lee Byung Chol. Oddly enough, but initially it was an organization that had nothing to do with advanced technology and electronics. Samsung's small grocery sold goods made in the Korean town of Daegu. Samsung began to be engaged in the production of electronics only in the 1960s and during this time was able to achieve heights in its business. At the moment, the grandson of the founder of this corporation is on the board of directors of the company.
Varieties of air conditioning systems
To save people from the heat of summer or the unpleasant sensations of turning off the heating in winter, air conditioners were invented. Many people, tired of the uncomfortable air temperature in their own home, buy household samsung air conditioners, it is enough just to not only install them, but also to dismantle them if necessary. To choose the right model of the device, you should first familiarize yourself with all the characteristics of different types, because it is impossible to buy a universal device that is suitable for every customer. For ease of installation and use, manufacturers produce different types of split systems, each of which meets different user requirements:
Inverter
Samsung inverter air conditioners differ from other models by the presence of a power electronics unit that helps to obtain alternating current of the required frequency. It is she who determines the speed of rotation of the engine. Such an air conditioner is able to smoothly change energy consumption and performance. The inverter allows you to very accurately maintain the set temperature and save energy.
Floor
The mobile floor unit does not have a lot of power, but it can be easily moved within the apartment and within the reach of the power source. Its complete set includes only one independent unit.
Vents
If you need to purchase the most simple cooling device, then the choice falls on samsung air conditioners or window air conditioners. Ease of use is ensured by the convenient location of all parts of the split system in one monoblock located under the window.
Wall mounted
The most popular solution is samsung wall-mounted air conditioners. Such devices are located on the wall under the ceiling and do not clutter up the space. Their external data help to be invisible in the interior and fit into any room, which is very important for a home split system.
Multizone
In buildings with several rooms, multi-zone air conditioners are used. Multi split systems are needed if you want to maintain a different microclimate in different rooms. Multi-split is cheaper than buying multiple air conditioners.
Cassette
Ceiling cassette industrial air conditioner. He is trusted with large volume air conditioning. Due to the distribution of air in four directions at once, such a device effectively cools the air.
Duct
Channel semi-industrial air conditioners. Cold air is distributed through the ventilation ducts, all equipment is hidden in the space above the ceiling, only the air distribution grilles are visible.
Column
Column air conditioner. Such systems do not require complex installation and are powerful at the same time. With a large enough volume, they do not take up much space due to their vertical shape. It is advisable to install these split systems in rooms with a large air volume. VRF systems. There is no fundamental difference between them and VRV. Both systems have a variable refrigerant flow. The price of it, the size of the case, the complexity of installation and connection of the split system will depend on the type of cooling electrical device. You can't save on Samsung split systems, because they are installed for a long time, and they give warmth in cold weather or cool in hot weather.
Comparison of characteristics of popular models
| Model / Parameter | ar09hqfnawkner | ar07hqfsawkner | 12 |
| Cooling, kW (device marking) | 2,75 | 2,05 | 3,50 |
| Heating, kW | 2,9 | 2,1 | 3,80 |
| Noise level, dB | 24/35 | 24/33 | 26/36 |
| Modes of operation. | Ventilation, night, temperature maintenance, dehumidification | ||
| Power consumption for cooling / heating, kW | 0,857/0,803 | 0,639/0,582 | 1,090/1,115 |
| Remote control. | Yes | Yes | Yes |
| Overview of additional functions. | Deodorizing filter | Deodorizing filter, fine filter |
Manual for control panel and air conditioners SAMSUNG
Each device is equipped with a signal receiving board, whose firmware allows the mechanism to be controlled remotely. The manufacturers of split systems tried to make the remote control for the Samsung air conditioner as easy to use as possible, but it is still strongly recommended to study the technical data sheet before using it, without it, the use of the air conditioner can lead to breakdown and replacement of spare parts. Just a few simple buttons are enough to control the mechanism:
- Power button. It starts the starting capacitor, turns on the motor or turns off the system.
- Switching operating modes. When pressed, it changes the mode in a circle. When setting the mode, it is necessary to select the temperature at which this household appliance can work correctly in the selected mode.
- Button for setting the required temperature. Helps to control the microclimate in the house. In fan mode, the button remains inactive.
- Fan speed selection.
- You can set the timer and select the start time.
It is worth paying close attention to the temperature range of the mechanism specified by the manufacturer. For example, if the air conditioner is used in too cold conditions, icing and cold damage can occur to important parts of the air conditioner: the compressor, fan blades, heat exchanger. This will lead to a breakdown of the mechanism and subsequent repair with replacement parts for spare parts.
It is necessary to clarify the temperature at which this or that model of the samsung air conditioner works without any complaints in the instructions for this model.
The instructions for Samsung air conditioners are easy to understand. All the necessary information is indicated on the screen of the remote control. The most important thing in the instructions is the scheme according to which the Samsung air conditioner is installed. A few tips for using the air conditioner:
- When the room is overcooled due to turning on the device to the maximum, it consumes more energy and is harmful to health.
- Electricity will be consumed as efficiently as possible if the impeller of the device is directed horizontally when the device cools the air, and almost vertically when it heats the air.
- A clean filter will also help reduce energy consumption. It is necessary to periodically check and clean the filters, in order to clean the inside of the device, it is necessary to disassemble it and remove the filter. Before that, you must unplug the device from the outlet. Cleaning with solvents or abrasive substances is not allowed, they spoil the appearance of the plastic cover.
- During the operation of the device, it will not be superfluous to check the windows again, they must be completely closed.
- For faster cooling, turn on the fan first.
- Servicing the appliance requires a professional to fill in refrigerant periodically. It is worth refueling at a service center that has a certificate and gives a guarantee. Only professionals can assemble and disassemble the device. Unfortunately, it is impossible to trace how much freon the master pours, we can only hope for his experience and the particularity of the service.
SAMSUNG air conditioner error codes
Error codes for Samsung air conditioners help to make an independent initial diagnosis of malfunctions of a household appliance. Repairing the Samsung air conditioner will not cause any difficulties after decoding the codes, because this information will help the master to quickly identify the breakdown and repair the device.
Some models of air conditioners are equipped with text mode. To enable this mode, you need to hold down the power button for about five seconds. The unit will report the presence of an error in operation using the indicator lamps on the panel of the indoor unit, which will either blink or light up in the specified sequence. The second will happen if there is an already identified error. If several errors are detected at once, then the system will first report a more dangerous malfunction.
Translation of the most common mistakes:
- The temperature measurement of the indoor unit heat exchanger is not correct.
- Incorrect fan speed. The error appears when the speed does not go beyond 450 rpm for 20 seconds.
- Incorrect measurement of the temperature indicator of the indoor unit.
- Icing of the outdoor unit.
Testing the device for faults occurs simultaneously with the automatic activation of the cooling mode. But the operation of the air conditioner at this moment undergoes some restrictions. Test mode requires entering cooling mode. It will work regardless of the set or internal temperature.
As soon as an error is found, its code is displayed on the screen and the user can diagnose it. The designation of errors corresponds to one of the codes, the decryption is attached to the instructions for the device.
If all the LEDs are blinking, without any order, then this may mean that all firmware has been deleted. In this case, flashing will help.
Samsung AQ 09 UGF
Selection of operating modes
Useful Tips
Cleaning your air conditioner
Precautionary measures
Disposal
Name of each part
Outdoor unit
2 - Air outlet, fan blades are visible behind the grill.
3 - Connections for connecting the refrigerant line.
Indoor unit
2 - Air outlet into the room. Closed when idle.
3 - Window for receiving commands from the remote control.
Preparation before starting work
Install batteries in the remote control. Observe the polarity and do not install different types of batteries in the remote control.
Selection of operating modes
... Automatic - you set the desired temperature range and the device automatically turns on heating if the room temperature is lower or cooling if the temperature is higher.
... Cooling - maintaining the air temperature in the room not higher than the value you specified. In this case, a dehumidifying effect is noted.
... Drying - a mode in which the air conditioner dries the air, cooling it as little as possible. In this mode, you cannot set the desired temperature.
... Heating - keeps the room warm.
... Ventilation - simply keeps the air in the room circulating.
Useful information:
The indoor unit is made with improved aerodynamics of the air cavity, therefore it works quietly and efficiently.
Additional modes and settings
This model compares favorably with a number of useful modes.
During operation, you can set the fan speed, which affects its volume and heat exchange rate.
You can manually specify the direction in the vertical plane and rotate the horizontal guides so that the air from the indoor unit flows continuously to the right or left.
The TURBO function is used with air cooling mode. Allows in a shorter time to cool the room to the desired numbers.
By using the good sleep function, you can get better sleep. Set the air conditioner to the time when you go to bed, the time to sleep and wake up, and it will independently maintain a colder temperature while falling asleep, slightly raise it during sleep and help you wake up invigorating with a portion of cold air.
There is also an on and off timer. The first one sets the time when the air conditioner should turn on. The second indicates the shutdown time. Thus, you can program the device to work independently at certain hours.
For cooling mode, a special Smartsaver mode is available. By turning it on, you save energy, since the air conditioner keeps the temperature range in the room from 24 to 30 degrees. If you want to set a lower value, you will have to disable this mode.
During operation of the air conditioner, its indoor unit is constantly in contact with condensate, which promotes the growth of fungi and mold in the air cavity of the unit. This mode should be used from time to time to prevent the appearance and growth of mold.
Useful Tips
To rationally use electricity, you need to monitor the position of the horizontal partition. When cooled, its direction should be closer to horizontal, when heated - closer to vertical.
Make sure that the windows are closed directly during the operation of the air conditioner, but do not forget to ventilate the room when the air conditioner is in operation for a long time.
Check and clean the air filter regularly - this saves energy.
To cool the room faster, first turn on the fan to TURBO mode.
Cleaning your air conditioner
Use a secure footing when cleaning the air conditioner. Do not forget to turn off the air conditioner using the remote control and then unplug it. Perform all actions with dry hands.
Do not use gasoline, solvents, abrasive detergents and hot water (more than 40 grams Celsius) to wash the air conditioner - all this can spoil the appearance of the plastic.
The device fails to turn on for 3 minutes after turning off. This is a normal protection against frequent engine starts. Wait and turn on the device after 3 minutes.
After turning on the heating mode, the indoor unit does not start working immediately. This is a protection against cold air blowing - wait until the heat exchanger warms up and the fan starts working.
When operating in heating mode, the indoor unit sometimes turns off. In this mode, it is necessary to periodically defrost the outdoor unit, so the operation of the air conditioner will stop periodically.
During dehumidification operation, the indoor unit is periodically turned off. The task of the air conditioner in this mode is to dry the air while minimally cooling it. Therefore, the indoor unit will shut down periodically.
After a power outage and the appearance of power in the network, the air conditioner turned on independently and began to work, although no one controlled it using the remote control. If the air conditioner was working before the power outage in the network, then after the power appeared, the automatic restart system turned it on to work in the same mode.
Water flows from the outdoor unit. This is normal, because when the air conditioner is operating, the heating main and other parts are cooled and condensation appears on them. In defrosting mode, ice is removed from the heat exchanger of the outdoor unit.
White smoke comes out of the outdoor unit. When the air conditioner heats up the room, cold air flows out of the outdoor unit, causing fog to appear.
Mist comes out of the indoor unit. If the air in the room is humid and the air conditioner is operating in cooling mode, the moisture will turn around the cold air stream leaving the air conditioner into mist.
The remote control does not work and the display is faded. Check the presence of batteries, the correctness of their installation, replace them with new ones.
The air conditioner does not cool well. Check if the windows, doors in the room are closed. Whether direct sunlight is heating the room, whether there are additional heating devices working. Is the operating mode set correctly?
The air conditioner does not cool / heat. This can happen if there is a refrigerant leak. Call the installer for advice and repair.
The air discharged from the indoor unit has an unpleasant odor. Perhaps the source is a wall, wallpaper or carpet near the indoor unit.
The indoor unit makes a crackling noise during operation. The change in temperature causes the plastic to change in size, which causes similar sounds.
Gurgling is audible during operation. This is normal as the movement of condensate and refrigerant can cause similar sounds. If a gurgling sound is heard when the air conditioner is off, this may be due to air being sucked in through the condensate drain hose during the operation of the exhaust ventilation.
Turn on self-cleaning mode to dry the water in the indoor unit.
Then turn off the air conditioner using the remote control.
Unplug the power outlet.
Connect the plug to an outlet with the correct wattage and make sure the air conditioner is properly grounded.
Install batteries of the same type in the remote control.
Turn on the air conditioner.
Installation work must be carried out by experienced professionals. The same applies to working with the mains.
Please note that the outdoor unit may make noise during operation, which may annoy people living nearby. The location should be selected so that there are no obstacles to the movement of air and it is possible to drain condensate.
Precautionary measures
Always use the instrument with a good earth connection.
Do not pull on the power cord, place solid or heavy objects on it, or step on it.
Do not insert fingers or pencils into the access holes of the air conditioner, otherwise injury may result.
Do not stand or place foreign objects on both air conditioner units.
Fasten the outdoor unit with high-quality, serviceable fasteners.
Make sure the power plug is clean and use only dry hands.
Do not modify, repair or change the power wire, air conditioner components.
Do not unplug the power plug while the air conditioner is running - first unplug it using the remote control.
Do not stay under a stream of cold air for a long time - this can harm your health.
If any oddities in the operation of the air conditioner (burning smell, strange noise) appear, turn it off, unplug it from the power supply and contact a specialist.
If the air conditioner stops heating / cooling, then it may be a refrigerant leak - contact a specialist.
Be sure to unplug the power plug before cleaning the device.
Ventilate the area while using the air conditioner.
Unplug this apparatus during lightning storms.
Hide
Samsung air conditioners are popular in Russia. Their main difference from air conditioners of other brands is their unique design in the Art Nouveau style.
The breakdowns are also minor and almost all of these malfunctions (error codes) of samsung air conditioners can be repaired in special service centers.
How to properly operate Samsung air conditioners, consumer reviews about them, we will consider in our article.
Samsung air conditioner - specifications
Under the Samsung trademark, they produce air conditioners using the latest technologies to create an excellent climate for their users.
Samsung air conditioners (instruction manual is attached to each model) are a combination of modern design, innovation and a full range of functions.
Samsung has mainly focused on the production of split systems for window, wall, cassette, column and duct type.
General features of Samsung air conditioners
Installing samsung air conditioner- uncomplicated and fairly fast. Such climatic equipment works almost silently, it is possible to adjust the air flow in three directions.
New models of Samsung air conditioners have the most economical energy class "A". Plus a convenient round-shaped liquid crystal screen (display) of digital input. With this display, you can monitor the "health" of the room. In addition to the power of the air conditioner and its current operating mode, the screen also displays the temperature in the room. The digital input screen monitors that the conditions in the apartment or house are comfortable for all users of the Samsung air conditioner (the instructions for the remote control are included with the climatic equipment).
Universal remote control for samsung air conditioner
Samsung air conditioners fit into any environment, blending harmoniously with the varied decor of the room. New models of air conditioners have a housing design that does not have slots. When the air conditioner is turned off, its front panel is closed, which has a clean surface and prevents dust accumulation thanks to a special filter. Therefore, all that is necessary for cleaning during the entire period of operation is to immediately wipe or rinse this panel.
And the absence of such a filter will lead to the accumulation of dust, and this, in turn, will reduce the operating life of the air conditioner and increase electricity consumption.
Samsung air conditioners - consumer reviews about their operation and repair
Today there are many sites that are dedicated to air conditioners under the Samsung trademark. So, for example, about samsung air conditioners - customer reviews in huge amount presented on the website "Klim24" ().
Wall mounted air conditioner Samsung
User Sergey says: “Before purchasing, I read a lot of reviews, and in many of them it was written that the outer unit of the samsung air conditioner vibrates and rumbles like a tractor. I absolutely disagree with this opinion, because I have familiar installers who have already installed more than a hundred such air conditioners, and everything is working properly, silently. Therefore, either you did not correctly install the Samsung air conditioners, or you had a marriage.
In general, I did not find any shortcomings in Samsung air conditioners, but their advantages include: reliability, simplicity, low noise level, attractive appearance and affordable prices. "
Samsung cassette air conditioner
On the same site ( http://www.clim24.ru/condicionery-samsung/otzivi.ht) user Stanislav believes that Samsung air conditioners have many advantages and disadvantages. So, from the pluses, he notes: “ modern design using blue backlight, useful additional functions(Smart Saver, Plasma Ion), comfortable dial with temperature display on the indoor module. "
And of the minuses: “the outer unit of the samsung air conditioner makes noise, but you can only hear it when the window is open. The supplied power drive is rather short, so I had to connect to an extension cable. And on the remote control for the samsung air conditioner there are many buttons and at first you get confused. And quite expensive, I would like to be cheaper. "
On the Wikimart website ( http://appliances.wikimart.ru/climatic/conditioners/model/31370777/kondicioner_samsung_aq07tsbn/) user Igor says: “I have been using Samsung air conditioners for a long time. And I haven't done it yet Samsung air conditioner repair only is an annual service. There were no problems, so I don't find any particular flaws. And of the advantages, one can single out: affordable quality-price ratio, ease of maintenance, ease of use, stylish appearance, cost-effectiveness. In a word, a worthwhile, reliable and inexpensive thing! "
Samsung window air conditioner
There are also completely negative customer reviews, for example, on the website torg.mail.ru ( http://torg.mail.ru/review/goods/aircons/samsung-9/) user under the nickname IRUSIK. IRINA shares: “I somehow got a Samsung air conditioner and two days later it was already broken. An error code was displayed on the screen. Everything samsung air conditioner errors I knew from the instructions and realized that it was impossible to do without repairs here. I thought I had to call the service center. But only this center ignored me for 2 months. And when the “specialists” did come, they could not repair the samsung air conditioner. After several more times they came and replaced the sensors and the unit, but the air conditioner did not work. They said they could do the dismantling, but at my expense. And then installing a samsung air conditioner again for my money. I asked for an opinion on the errors of the Samsung air conditioner, so I could hand it back to the store. In response, the company, to put it mildly, dumped us! "
Duct air conditioner Samsung
Such a service as quality repair of samsung air conditioners in Moscow, is provided by the site "Rembitteh" (http://rembitteh.ru/). High quality and the correctness of the repair work by the specialists of this site is confirmed by consumer reviews. For example, the user Olga says: “The application was accepted promptly, and the master arrived at a convenient time for us. In general, we are extremely satisfied, the air conditioner is working perfectly again! ”.
Instructions on the following model:
Samsung AQ 09 UGF
Samsung AQV09YWB
Air conditioner Samsung AQ 09 UGF
Selection of operating modes
Useful Tips
Cleaning your air conditioner
Precautionary measures
Disposal
In the manufacture of this, substances are used that can be used for recycling. Therefore, check with your area how to dispose of according to local regulations.
Name of each part
Outdoor unit
1 - Air intake on the back-side surface.
2 - Air outlet, fan blades are visible behind the grill.
3 - Connections for connecting the refrigerant line.
Indoor unit
1 - Air intake to the indoor unit.
2 - Air outlet into the room. Closed when idle.
3 - Window for receiving commands from the remote control.
Remote control
Preparation before starting work
Before turning on, make sure the air conditioner is connected to an outlet with sufficient power and is properly grounded. Make sure that there are no obstacles to air movement around the outdoor and indoor units (curtains, etc.).
Install batteries in the remote control. Observe the polarity and do not install different types of batteries in the remote control.
Selection of operating modes
The following operating modes are available for this air conditioner:
Automatic - you set the desired temperature range and the device automatically turns on heating if the room temperature is lower or cooling if the temperature is higher.
Cooling - maintaining the air temperature in the room not higher than the value you specified. In this case, a dehumidifying effect is noted.
Drying - a mode in which the air conditioner dries the air, cooling it as little as possible. In this mode, you cannot set the desired temperature.
Heating - keeps the room warm.
Ventilation - simply keeps the air in the room circulating.
Useful information: in heating mode, the air conditioner does not turn on the indoor unit immediately, but after 3-5 minutes. This is necessary to warm up the heat exchanger and protects the user from cold air supply. In addition, in this mode, freezing of the outdoor unit occurs, therefore, the operation of the air conditioner periodically stops (no more than 10 minutes) to defrost the frozen parts.
The indoor unit is made with improved aerodynamics of the air cavity, therefore it works quietly and efficiently.
This model compares favorably with a number of useful modes.
During operation, you can set the fan speed, which affects its volume and heat exchange rate.
You can manually specify the direction in the vertical plane and rotate the horizontal guides so that the air from the indoor unit flows continuously to the right or left.
The TURBO function is used with air cooling mode. Allows in a shorter time to cool the room to the desired numbers.
By using the good sleep function, you can get better sleep. Set the air conditioner to the time when you go to bed, the time to sleep and wake up, and it will independently maintain a colder temperature while falling asleep, slightly raise it during sleep and help you wake up invigorating with a portion of cold air.
There is also an on and off timer. The first one sets the time when the air conditioner should turn on. The second indicates the shutdown time. Thus, you can program the device to work independently at certain hours.
For cooling mode, a special Smartsaver mode is available. By turning it on, you save energy, since the air conditioner keeps the temperature range in the room from 24 to 30 degrees. If you want to set a lower value, you will have to disable this mode.
During operation of the air conditioner, its indoor unit is constantly in contact with condensate, which promotes the growth of fungi and mold in the air cavity of the unit. This mode should be used from time to time to prevent the appearance and growth of mold.
Useful Tips
Do not turn on the air conditioner to the maximum and overcool the room. You can harm your health and this will lead to waste of energy.
To rationally use electricity, you need to monitor the position of the horizontal partition. When cooled, its direction should be closer to horizontal, when heated - closer to vertical.
Make sure that the windows are closed directly during the operation of the air conditioner, but do not forget to ventilate the room when the air conditioner is in operation for a long time.
Check and clean the air filter regularly - this saves energy.
To cool the room faster, first turn on the fan to TURBO mode.
Cleaning your air conditioner
Use a secure footing when cleaning the air conditioner. Do not forget to turn off the air conditioner using the remote control and then unplug it. Perform all actions with dry hands.
Do not use gasoline, solvents, abrasive detergents and hot water (more than 40 grams Celsius) to wash the air conditioner - all this can spoil the appearance of the plastic.
If you think there is a problem
The air conditioner does not work. Check if the plug is connected to the outlet, if there is power in the network, if the normal voltage figures are not exceeded.
The device fails to turn on for 3 minutes after turning off. This is a normal protection against frequent engine starts. Wait and turn on the device after 3 minutes.
After turning on the heating mode, the indoor unit does not start working immediately. This is a protection against cold air blowing - wait until the heat exchanger warms up and the fan starts working.
When operating in heating mode, the indoor unit sometimes turns off. In this mode, it is necessary to periodically defrost the outdoor unit, so the operation of the air conditioner will stop periodically.
During dehumidification operation, the indoor unit is periodically turned off. The task of the air conditioner in this mode is to dry the air while minimally cooling it. Therefore, the indoor unit will shut down periodically.
After a power outage and the appearance of power in the network, the air conditioner turned on independently and began to work, although no one controlled it using the remote control. If the air conditioner was working before the power outage in the network, then after the power appeared, the automatic restart system turned it on to work in the same mode.
Water flows from the outdoor unit. This is normal, because when the air conditioner is operating, the heating main and other parts are cooled and condensation appears on them. In defrosting mode, ice is removed from the heat exchanger of the outdoor unit.
White smoke comes out of the outdoor unit. When the air conditioner heats up the room, cold air flows out of the outdoor unit, causing fog to appear.
Mist comes out of the indoor unit. If the air in the room is humid and the air conditioner is operating in cooling mode, the moisture will turn around the cold air stream leaving the air conditioner into mist.
The remote control does not work and the display is faded. Check the presence of batteries, the correctness of their installation, replace them with new ones.
The air conditioner does not cool well. Check if the windows, doors in the room are closed. Whether direct sunlight is heating the room, whether there are additional heating devices working. Is the operating mode set correctly?
The air conditioner does not cool / heat. This can happen if there is a refrigerant leak. Call the installer for advice and repair.
The air discharged from the indoor unit has an unpleasant odor. Perhaps the source is a wall, wallpaper or carpet near the indoor unit.
The indoor unit makes a crackling noise during operation. The change in temperature causes the plastic to change in size, which causes similar sounds.
Gurgling is audible during operation. This is normal as the movement of condensate and refrigerant can cause similar sounds. If a gurgling sound is heard when the air conditioner is off, this may be due to air being sucked in through the condensate drain hose during the operation of the exhaust ventilation.
When the air conditioner will not be used for a long time (At the end of the season of use)
If you are not going to use the air conditioner for a long time, then you need to prepare it for downtime.
Turn on self-cleaning mode to dry the water in the indoor unit.
Then turn off the air conditioner using the remote control.
Unplug the power outlet.
To turn on after a period of no operation
Check if there are any obstructions in the air flow around the outdoor and indoor units.
Connect the plug to an outlet with the correct wattage and make sure the air conditioner is properly grounded.
Install batteries of the same type in the remote control.
Turn on the air conditioner.
Installation site and electrical work
must be carried out by experienced professionals. The same applies to working with the mains.
Please note that the outdoor unit may make noise during operation, which may annoy people living nearby. The location should be selected so that there are no obstacles to the movement of air and it is possible to drain condensate.
Precautionary measures
The power cord must be connected to an outlet with sufficient capacity. Do not plug it into an extension cord.
Always use the instrument with a good earth connection.
Do not pull on the power cord, place solid or heavy objects on it, or step on it.
Do not insert fingers or pencils into the access holes of the air conditioner, otherwise injury may result.
Do not stand or place foreign objects on both air conditioner units.
Fasten the outdoor unit with high-quality, serviceable fasteners.
Make sure the power plug is clean and use only dry hands.
Do not modify, repair or change the power wire, air conditioner components.
Do not unplug the power plug while the air conditioner is running - first unplug it using the remote control.
Do not stay under a stream of cold air for a long time - this can harm your health.
If any oddities in the operation of the air conditioner (burning smell, strange noise) appear, turn it off, unplug it from the power supply and contact a specialist.
If the air conditioner stops heating / cooling, then it may be a refrigerant leak - contact a specialist.
Be sure to unplug the power plug before cleaning the device.
Ventilate the area while using the air conditioner.
Unplug this apparatus during lightning storms.
Samsung Air Conditioner
Table of contents
Disposal
Name of each part
Preparation before starting work
Selection of operating modes
Additional modes and settings
Useful Tips
Cleaning your air conditioner
If you think there is a problem
When the air conditioner will not be used for a long time (At the end of the season of use)
Installation site and electrical work
Precautionary measures
Disposal
Recyclable substances are used in the manufacture of this air conditioner. Therefore, check with your area how to dispose of according to local regulations.
Name of each part
Outdoor unit
Air enters the heat exchanger at the rear as well as the lateral surfaces (1). Displays from the front (2).
Indoor unit
Remote control
Preparation before operating the air conditioner
Please note that the installation and connection of the device to the mains must be carried out by specialists who have similar experience work.
Devices of such power should be connected to a network that can withstand the peak loads that occur during operation. Grounding must be present.
When choosing batteries for the remote control, remember that both must be of the same type (company) and discharge level. Do not use rechargeable batteries.
Selection of operating modes
The device connected to the network must be started using the remote control. Further, you can select the operating mode by successively pressing the MODE button.
For the mode of comfortable use of the air conditioner, you can turn on the "Auto" mode. It has the ability to set the desired temperature range, which will allow you not to be distracted once again. When the temperature drops below or vice versa when the value is exceeded, the mode required in this case (heating / cooling) will automatically turn on.
If it is steadily hot (cold) outside, then one mode will do. Heating with an air conditioner has the feature that the device will have to stop periodically to defrost the frozen outdoor unit.
When choosing dehydration, the device will remove moisture, thus dosing the work in order to cool the air to a minimum.
In fan mode, the device not only organizes air recirculation, but also cleans it using built-in filters.
Additional modes and settings
To prevent too dry air in the room, the Comfort function monitors that the humidity matches the temperature.
The high-performance filter not only removes microparticles from the air, it perfectly removes allergens from the air.
Ionization will also be very useful in an apartment with electrical appliances, which nowadays are increasingly shifting the ionic balance not in a healthy direction.
The Turbo function for the fan allows you to quickly reach the desired room temperature.
Since the electrical system is inverter, the device is quieter and produces less load on the electrical network.
Useful Tips
When cooling the air, try not to set too low numbers - this may not be beneficial to health and lead to energy waste.
Make sure that the windows and doors of the room are closed, otherwise the newly cooled air will simply leave the room.
If there is a heating device in the room or there are many people, the cooling work will be slower.
Watch out for curtains and blinds - direct sunlight also heats the room and interferes with the air conditioner.
Be sure to ventilate the area (sometimes) to restore oxygen to normal.
Cleaning your air conditioner
Be sure to use a sustainable base when cleaning your conditioner.
Do not perform any action until you have disconnected the plug from the outlet with dry hands. Do not use solvents (eg. Bezin), hot water and abrasives - all this can spoil the appearance of the plastic.
If it suddenly seems that there is a problem
If the device simply does not work, check that it is connected to the mains and that there is current in it. Also check if the remote control is not working. In this case, you need to make sure that the batteries are installed correctly (polarity), which are in good working order.
If you suddenly cannot turn on the device immediately after turning it off, then this may be the protection against frequent switching on. Wait a bit and try a little later.
Cold air can flow from both blocks in different modes, this can be accompanied by the appearance of fog near the flow of cold air.
It is normal to stop in operation for 10 minutes or not to start immediately after pressing a button on the remote control when heating the room. Firstly, the indoor unit must warm up, and secondly, periodically it is necessary to defrost the outdoor unit, while the operation temporarily stops.
The manifestation of the operation of the automatic restart system can be mistaken for a malfunction. This function will automatically turn on the device after an emergency power outage in the network.
It is normal for the plastic to crackle when heated.
Gurgling and splashing sounds may accompany the movement of water (condensate) and refrigerant through the pipes.
Condensation may occur from the air conditioner during heating / cooling, this is normal.
If it is not possible to cool the room, then you should check: whether the operating mode is set correctly, whether the windows are open, whether there are heating devices on in the room. It is possible that the device is interfered with by dirt in the air filter or direct sunlight through the windows.
Odor may be due to dirty indoor unit or air filters.
When your air conditioner will not be used for a long time
Run heating for 3 (2-3) hours to dry the indoor unit. Then disconnect from the mains and remove the batteries from the remote control.
Before starting for the first time in a long time, check that there are no obstacles to air movement, and that grounding is working. After installing the batteries, turn on the device to the mains.
Place for installation
Do not use the device in locations where flammable gases or hydrogen sulfide will be expected in the air. Do not apply it in places where there is a lot of machine oil. Condensation must be drained from the outdoor unit and it can make noise that will disturb people.
Do not install the air conditioner in places close to high-frequency equipment and electronics.
Precautionary measures
Be sure to check the correct network connection. Appliances of such power must be directly connected to a powerful socket with a grounding; the use of extension cords is unacceptable.
It is impossible to change (modify) or repair the air conditioner on your own.
Connecting and disconnecting to / from the mains must be done with dry hands.
It is forbidden to place any objects on both units, power cord.
Do not pull out the plug from the socket while the device is running - first stop it using the remote control.
It is dangerous to stick objects of any kind inside the appliance - the high-speed fan may cause injury.
The appearance of a burning smell or unusual sounds should alert you - disconnect the device from the mains and call the installers.
Do not expose people and animals to cold air for long periods.
It is not recommended to place foreign objects and electrical appliances under the air conditioner - water (condensation) may drip from it.
If your air conditioner stops heating and cooling, then you need to check if there is a refrigerant leak.